User guide

5
English
TAPE DECK (CD-R/MD) OPERATION
TAPE (CD-R/MD) PLAYBACK
1. Press the CD-R/MD or TAPE switch A. The indicator above the
switch will light up.
2. Play a prerecorded tape on the tape deck (or CD-R).
3. Adjust the volume with the VOLUME control B.
NOTES:
• Set the CD-R/MD TAPE switches to OFF when a tape is not to be
played.
• The tape can be played regardless of the setting of the INPUT
SELECTOR C.
TAPE RECORDING
The playback sound of a program source component, such as a
turntable, a tuner, or a CD player, can be recorded on tape as follows.
1. Set the INPUT SELECTOR switch C to select the program source to
be recorded.
2. Play the program source.
3. Operate the tape deck (or CD-R) to record the playback sound on
tape.
NOTE:
Playback and recording onto tape decks is not possible while the
SOURCE DIRECT switch is pressed in.
TAPE MONITORING
When a three-head tape deck is connected to the TAPE jacks, the sound
recorded on tape can be monitored through the speakers by pressing
the TAPE monitor switch A. In this case, the tape deck must be
connected to this unit via both recording and playback connection
cords.
NOTE:
When the tape deck is a two-head system, the recorded sound cannot
be monitored even when the CD-R/MD TAPE switch A is pressed. In
this case, however, the sound of the program source being recorded
can be monitored.
When the program source selected by the INPUT SELECTOR is to be
recorded onto the tape deck connected to the TAPE jacks, do not press
the CD-R/MD switch.
If the CD-R/MD switch is pressed, the unit enters CD-R fi TAPE copy
mode.
DUBBING OF PRERECORDED TAPES
If you connect two tape decks to this unit, the contents of a prerecorded
tape can be copied onto another tape. For example, you can record only
the desired tunes on a tape containing an FM radio program onto another
tape, or you can copy the contents of an open-reel tape onto a cassette
tape. When the CD-R/MD switch is pressed, this unit automatically enter
the CD-R/MD (TAPE 2) fi TAPE (TAPE 1) copy mode, and the playback
signal of tape deck 2 can be copied onto tape deck 1.
NOTES:
• When both of the CD-R/MD and TAPE switches are pressed in. The
sound recorded from CD-R/MD to tape deck can be monitored
through the speakers.
• During dubbing, the program source selected by the INPUT SELEC-
TOR switch cannot be listened to.
• When the program source selected by the INPUT SELECTOR switch
is recorded simultaneously by the CD-R (or MD) and tape deck, the
sound recorded by CD-R or MD cannot be monitored. If the CD-R/MD
switch is pressed, the signal of CD-R/MD will be output to tape deck.
• When a component such as a surround processor or graphic
equalizer is to be used, connect the component to the TAPE IN/OUT
jacks and press the TAPE switch.
TAPE CD-R/MD
SOURCE DI REC T
INTEGRATED AMPLIFIER PM6010OSE
TAPE CD-R/MD
MUTE
MIN MAX
LR
CD
PHONO TUNER
AUX
INPUT SELECTOR VOLUME
BALANCE
POWER ON/OFF
PHONES
ON
OFF
ON
OFF
ON
OFF
C B
Control used for operating the tape deck.
A
COPY
CD-R>TAPE
Switch Setting
Indicators
Speaker Output
CD-R/MD OUT Jack Output
TAPE OUT Jack Output
CD-R/MD TAPE TAPE
CD-R/MD CD-R/MD
Source selected by INPUT
SELECTOR
Source selected by INPUT
SELECTOR
Source selected by INPUT
SELECTOR
Source selected by INPUT
SELECTOR
Source selected by INPUT
SELECTOR
Source selected by INPUT
SELECTOR
Source selected by INPUT
SELECTOR
CD-R/MD
CD-R/MD
OFF
TAPE COPY CD-R/MD TAPE COPY CD-R/MD TAPE COPY CD-R/MD TAPE COPY
TAPE
OFF
CD-R/MD
ON
TAPE
OFF
CD-R/MD
OFF
TAPE
ON
CD-R/MD
ON
TAPE
ON
TAPE MONITOR SWITCH OPERATION CHART