Model RX9001 User Guide Serial Extender ENGLISH FRANÇAIS ESPAÑOL
EN WARNINGS • • • • FR AVERTISSEMENTS • • • • ES Do not expose the equipment to rain or moisture. Do not remove the cover from the equipment. No naked flame sources, such as lighted candles, should be placed on the equipment. No objects filled with liquids, such as vases, shall be placed on the equipment. Ne pas exposer l’appareil à la pluie ni à l’humidité. Ne pas essayer de retirer le boîtier de l’appareil. Ne placer aucune source de flamme nue, comme une bougie allumée, sur l’appareil.
ESPAÑOL FRANÇAIS ENGLISH RX9001 User Guide RX9001 User Guide
RX9001 User Guide RX9001 User Guide Contents Before You Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Unpacking the Extender . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Installing the Extender .
RX9001 User Guide The Serial Extender is an important element of the RC9001 System and makes it possible to control A/V equipment via RF in the entire house. In addition, it can be connected to A/V equipment via RS232 and allows you to use power sensing for reliable power on/off switching. You can also use it to control drapes and projector lifts, for example.
RX9001 User Guide Unpacking the Extender Serial Extender Front Panel 4 groups of 4 LEDs each for the • IR ports; • Serial (RS232) ports; • Sensor inputs; • Relay outputs.
RX9001 User Guide Power Adapter Configuration Cable 2 Dual IR Emitters 2 Mini-jack IR Cables ENGLISH Crossed Ethernet cable Mounting Kit x2 x6 x4 x4 x4 Installing the Extender Mounting the Extender in a Rack Warning Keep the Extender away from heat sources such as amplifiers. Fit the mounting plate on the Extender with the screws. Attach the Extender to a rack, using the screws, washers and nuts.
RX9001 User Guide Connecting the Extender to External Equipment The Extender can be connected to external equipment through the various outputs on the back panel. Warning Make sure that the equipment is always turned off before connecting it to the Extender. Attaching the Extender to Infrared Controlled A/V equipment For the Extender to transmit an IR signal, you need to connect it to the A/V component via the IR Output on the back of the Extender.
RX9001 User Guide When the Control Panel sends out a macro to switch multiple A/V components on or off, discrete codes are normally used to ensure the state of the component. In some cases, only toggle codes are available: one command toggles between the on and off state, and there is no separate command for switching the component on and switching it off. In this event, the system may get out of sync.
RX9001 User Guide Connecting to Relay-controlled Equipment Use standard wiring and Phoenix connectors. Connecting to Serial Equipment There are two ways to connect serial equipment to the Extender: Use a serial cable. Note 7 For most A/V components a standard female to male or female RS232 cable can be used.
RX9001 User Guide ENGLISH Use standard wiring and Phoenix connectors. Tip In case you experience communication problems when using the RS232 wiring solution illustrated above, make sure that the GND pin on the Extender is grounded correctly on the side of the A/V component. A/V component Extender Connecting to a Lutron RadioRa Lighting System 1 Connect the Lutron Lighting System to the Extender via the RS232 port. Refer to chapter ‘Connecting to Serial Equipment’ on page 7. 2 Open Wizz.it Ex.
RX9001 User Guide Inserting a Multimedia Server in the Network You can add an Escient Media Server or an Imerge Sound Server to your network. 1 Connect the Server to the router. 2 Open Wizz.it Ex. 3 Open the configuration file. 4 To insert a Multimedia Server in the configuration file, click the ‘Insert Escient Media Server’ button or the ‘Insert Imerge Sound Server’ button. 5 Open the Multimedia Server Properties.
RX9001 User Guide 4 Plug in the Extender’s power adapter. The Extender will start up. After startup, the Power and Ethernet LEDs are green. The Busy LED blinks green when it’s processing a code or a macro. You can connect the Extender directly to the PC for configuration. If the Extender is already installed and connected to external equipment, it is also possible to configure it through a router. For further instructions, refer to the topic ‘Configuration through a router’ on page 11.
RX9001 User Guide Configuration through a router 1 The Extender is already connected to the router. Connect the router to the PC as well. Straight Ethernet cable Extender Router 2 Set the Configuration switch to 3 for configuration: Configuration switch: 3 The Extender will restart. After start-up, the Power and Ethernet LEDs are green and the Busy LED is red/green blinking. 3 Open Wizz.it Ex on the PC. 4 In the Tools menu, select Extender Discovery.
RX9001 User Guide Support ENGLISH Troubleshooting What Do the LEDs Indicate? LEDs Ethernet LED Busy Green blinking The Extender’s IP address is being determined. The Extender is busy processing a code or short macro from a Control Panel. Green The Extender is functioning normally. The Extender is busy processing a long macro from a Control Panel. Colors Red/green blinking The Extender is in configuration. Red Refer to the topic ‘There is an IP conflict’ on page 12.
RX9001 User Guide Operating A/V components with the Extender The A/V components do not respond to commands from the Extender • Check if the Busy LED blinks green when you send a command with the Control Panel. If the Busy LED does not blink, the Extender is not receiving commands from a Control Panel. • Make sure that the Control Panel is configured correctly in Wizz.
RX9001 User Guide 6 Select Firmware Update in the left navigation pane. The Firmware Update page opens. When you are asked to browse to the update file, you need to select the ZIP file you downloaded earlier from the website. Updating the Extender through a Router ENGLISH 7 Follow the onscreen instructions. If the Extender is already installed and connected to equipment, it may be more convenient to update it through the router. 1 The Extender is already connected to the router.
RX9001 User Guide Specifications General IP based Extender box for remote RC9001 Control Panel operation Dark grey metal housing for 19” rack mounting or free standing position Up to 16 Extenders and 16 Control Panels in a system Connectivity 5 VDC power input 4 addressable outputs for IR emitters Ethernet RJ45 connection 4 standard RS232 ports for control 4 power sense inputs: 4-30 VDC or 4-30 VAC rms 4 Relay outputs: 48 VDC or 48 VAC rms, 2 A (max power 60 W) Voltage output for general use: 5 VDC, 0.
ENGLISH RX9001 User Guide 16
IFU Approbation / Safety Content FCC Compliancy This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rule.
Finnish Vanhan tuotteen hävittäminen Tuotteesi on suunniteltu ja valmistettu laadukkaista materiaaleista ja komponenteista, jotka voidaan kierrättää ja käyttää uudelleen. Tuotteeseen kiinnitetty yliviivatun roskakorin kuva tarkoittaa, että tuote kuuluu Euroopan parlamentin ja neuvoston direktiivin 2002/96/EC soveltamisalaan. Ota selvää sähkölaitteille ja elektronisille laitteille tarkoitetusta kierrätysjärjestelmästä alueellasi.
IFU Approbation / Safety Content Polish Usuwanie zużytych produktów Niniejszy produkt został zaprojektowany i wykonany w oparciu o wysokiej jakości materiały i podzespoły, które poddane recyklingowi mogą być ponownie użyte. Jeśli na produkcie znajduje się symbol przekreślonego pojemnika na śmieci na kółkach, podlega on postanowieniom dyrektywy 2002/96/WE. Należy zapoznać się lokalnymi zasadami zbiórki i segregacji sprzętu elektrycznego i elektronicznego.
IFU Approbation / Safety Content Marantz America, Inc.
www.marantz.com You can find your nearest authorized distributor or dealer on our website. is a registered trademark.