Operation Manual

24
ENGLISH
HDMI JACK
This unit has two HDMI inputs and one HDMI output. It
can send digital video and audio signals from DVDs and
other sources directly to a display. It minimizes signal
degradation caused by analog conversion so that high
quality images can be enjoyed.
Select an input source from the OSD menu system.
(See page 26)
Notes:
• When the HDMI output is connected to a display
monitor that does not support HDCP, signals are not
output. To view images in HDMI, it is necessary to
connect to a display that supports HDCP.
• There may be no image output if connected to a
TV or display that is not compatible with the above
format.
• Refer to the instruction manual of the TV or display
to be connected to the SR4001/SR5001 for detailed
information regarding the HDMI terminal.
* HDCP: High-bandwidth Digital Content Protection
CONNECTING HDMI DEVICES
An HDMI cable (sold separately) is used to connect the
HDMI jack on the SR4001/SR5001 with the HDMI jack
on a DVD player, TV, projector or other component. To
transmit multichannel audio via HDMI, the connected
player must support multichannel audio transmission
through its HDMI jack.
HDMI video streaming is compatible with DVI in principle.
Therefore, it is possible to connect to a TV or monitor that
has a DVI terminal using an HDMI-DVI conversion cable
or plug. When connecting to a DVI terminal, connect the
audio signal separately.
Notes:
• Some HDMI components can be controlled over the
HDMI cable, but this receiver cannot control other
components this way.
• When connected to a monitor (i.e., TV, projector,
etc.) that does not support HDCP, video and audio
are not output.
• DVI cables come with 24-pin and 29-pin plugs. This
receiver supports 24-pin DVI-D cables; 29-pin DVI
cables cannot connect to it.
• Some source devices such as DVD players do not
support HDMI repeater operations like those of
the SR4001/SR5001. In such case, pictures are not
properly projected on monitors such as TVs and
projectors.
• When multiple components are connected to this
receiver, turn power to unused components off to
prevent interference between them.
• Disconnecting or connecting cables with the power
on can damage the equipment. Turn the power off
before disconnecting or connecting cables.
• Some DVD-Audio disks disable downmixing.
These types of disks are not played back correctly
unless the left, center, right and surround left and
right speakers, and subwoofer are connected.
• If a DVD player that does not support HDMI 1.1
is connected to the SR4001/SR5001, multi channel
PCM playback is not possible even with DVD-
Audio disks.
•
If a DVD player or other device with DVI output is
connected to the SR4001/SR5001, a separate audio
cable (i.Link, optical-digital, coaxial digital or analog)
is needed for the audio signals. In this case, select
the connected audio input as explained in “1 INPUT
SETUP”. (See page 26)
• Multi channel PCM signals and audio signals of 62
kHz or higher that are input from the HDMI jack are
not output from the DIGITAL OUT jacks.
• Depending on the quiality of the cable used, the
HDMI signal may be affected by noise.
• Audio units that use sampling frequencies of 128
kHz and above are not supported.
DVD player VIDEO PROJECTOR
XM
FLASHER
IN
DC
TRIGER
COAX
IN
OUT
RC-5
1
4
3
OPT
DIGITAL OUT
C R / P R C B / P BY
OUTIN
CDR/MD
OUTIN
TAPECDVCR1
AUDIO
DSS/VCR2
IN
N
OUT
C R / P R C B / P BYDSS/VCR2
R
IN VCR OUT MONITOR OUT
INPUT
1
INPUT
2
INPUT 2 OUTPUTINPUT 1
HDMI Ver 1.1
COMPONENT
VIDEO
MODEL NO. SR5001
C R / P R C B / P BY
INPUT
3
MONITOR
OUT 2
2 3
DIGITAL IN
RR
CENTERSURROUNDSURROUND BACK
SPEAKER C/
MULTI SPEAKER
LLLR
FRONT A
T
ER,
INIMUM 6 OHMS
MUM 8 OHMS
SPEAKER
SYSTEMS
AC IN
1.25A 150W
AC OUTLETS
120V 60Hz
UNSWITCHED
SWITCHED
1.25A 150W
INPUT 2 OUTPUTINPUT 1
HDMI Ver 1.1
HDMI OUTPUT
HDMI INPUT
HDMI OUTPUT
Satellite Tuner