Radio User Manual
7
ENGLISH
MEMORY PRESETTING
7
Manual operation
For example: presetting FM 90.1 MHz, to Preset number. 10
1. Select the FM by using the BAND button !7.
2. Tune to 90.1 MHz by using the TUNING 5∞ button i.
3. Press the MEMO button !1 briefly (for less than 0.5
second) Then, “MEMO” will blink in the display.
4. Select the preset number by using the PRESET 5∞
button !4.
5. MEMO button !1 pushed again, 90.1 MHz (broadcast
station) was able to be memorized in number 10 by this.
Note
Be sure to select the antenna A or B memorization when
you preset manual memory in FM broadcast.
7
Automatic operation
1. Select the desired broadcasting (FM, AM, or LW) by
using the BAND button !7.
2. Press the MEMO button !1 slightly longer than 1.5
second does.
Then, broadcasting will be automatically received, and
as many broadcasting station are received well will be
memorized preset number-01 after another.
3. Check the broadcasting station by using the PRESET
5∞ button !4.
Note
• In the case of FM automatic presetting, the antenna A, B
selector is set to “A” automatically,
And the broadcasting station is scanned twice. The
stations that have stronger broadcasting signal are preset
in the first time.; weaker ones are preset in the second
time.
• If a new broadcasting station is preset into a channel the
broadcasting station which has been preset into that
position area will be automatically erased.
• In mountainous or remote area broadcasting stations
which have weak broadcasting signals cannot be
automatically preset into the memory.
• Max. 30 broadcasting stations each for FM, AM(MW and
LW) bands can be preset.
LISTENING TO RADIO
1. Select FM, AM, or LW by using the BAND button !7.
2. Tune to the desired broadcast by using the TUNING i
or PRESET 5∞ button !4.
3. FM broadcasting is set up to “STEREO” mode
If the broadcasting signal is weak, or if there is a large
amount of interference in FM stereo broadcast, change
the monaural mode by presetting the FM MODE button
!5.
4. Select the IF BAND (FM bandwidth)
Select the NARROW bandwidth by pressing this button if
the broadcast signal is interfered with adjacent
broadcast in the FM .
FINE, MANUAL TUNING
This function used for selection the manual tuning of the fine
tuning mode.
Fine tuning mode is available only in the FM mode.
1. Press the TUNING MODE button u.
2. Every time you press this button, the following will be
displayed FINE ⇔ MANUAL.
7
In FINE (Tuning) mode
When you try press the TUNING 5∞ button i, the
frequency will be selected by 10 kHz step to ±50 kHz.
Then, it will automatically be set to the MANUAL mode in 4
second.
7
In MANUAL (Tuning) mode
1. Press the TUNING 5∞ button i in the FM band, then
the frequency will be selected by 50 kHz step.
2. In the MW band, the frequency will be selected by 9 kHz
step.
3. In the LW band, the frequency will be selected by 1 kHz
step.
OPERATIONS
FM/AM TUNER ST6001
ANTETTA
IF BAND
FM
ON/STAMDBY
POWER
STANDBY
WIDE
NARROW
AB
RDS
TIMER SET
BAND
ON/OFF
FM MODE
PRESET
UP
DOWN
UP
DOWN
TUNING
MEMONEXT
CANCEL
TUNING
MODE
/DISPLAY
ST.NAME
TIME ADJ.
TIMER
DAILY ONCE
TUNED STEREO RDS PTY PT TP TA
PRESET
kHz
MHz
CH
MEMO
ui !1
!4
!5 !7
ST6001N 01 Eng 06.1.20 10:34 AM ページ7