Radio User Manual

10
ENGLISH
RDS DISPLAY
1. Select the FM band. RDS can be received only in FM.
2. Select the RDS broadcasting by using the TUNING 5∞
button i.
Then, RDS will light up in the upper side of the FTD
display. And the related data, if received, will be
displayed in the type of received data (PTY, RT, TP, TA)
3. RDS
1) The default of the RDS mode is PS.
2) Press the RDS button !6.
Each time you press the button briefly (1.5 second or
less), the modes will change as follows
PS
→→
PTY
→→
RT
→→
TA
→→
CT
→→
PS
3) PS mode
– When you select the PS with the RDS button !6, “PS”
will blink for about 4 seconds.
– After 4 seconds, PS or a station name entered by
manual file will be displayed.
4) PTY mode
– When you select the PTY with the RDS button !6,
PTY will blink for about 4 seconds, the type of
received PTY will be displayed.
– If there is no PTY data among received broadcasting,
RDS mode will be switched to PS mode
automatically.
5) RT mode
– When you select the RT with the RDS button !6, “RT”
will blink for about 4 seconds, After 4 seconds, the
data received broadcasting, the RDS mode will be
automatically switched to the PS mode.
6) TA mode (TP search function)
– When you select the TA with the RDS button !6, “TA”
will blink for about 4 seconds, TP received
broadcasting will be searched with the FM frequency
increasing in 50 kHz steps.
– If TP received broadcasting is searched, the increase
in frequency will be stop and it is asked whether TA
will be received or not.
– If TP and TA turn off while you are receiving the TA,
the tuner will search the TA broadcasting again with
the FM frequency increasing in 50 kHz steps.
7) CT mode
– When you select the CT with the RDS button !6, “CT”
will blink for about 4 seconds. After 4 seconds, the
clock time together with the frequency will be
displayed. “CT” can be received regardless of
whichever RDS mode. The tuner is set to.
* Not to use CT mode,
1. Press and hold the RDS button !6 for longer than 8
seconds, and press briefly the RDS button !6 within 0.5
seconds.
– The indicator will be changed as follows:
PS
→→
PTY
→→
RT
→→
TA
→→
(NO CT)
→→
PS
– In this mode, although “CT ” data are entered, the
time is not changed to the current time.
2. In ”NO CT“ mode, press and hold the RDS button !6 for
longer than 8 seconds.
– The indicator will be changed as follows:
PS
→→
PTY
→→
RT
→→
TA
→→
CT
3. PTY Search
1) Press the RDS button !6 for longer then 1.5 second.
Then “SEARCH” will be shown in the display.
2) Select the desired PTY mode by using the PRESET
5∞ button !4.
3)
– If you press the NEXT button !0, the PTY mode wills
blink in the clock display.
– Searching will start when you push the TUNING 5∞
button i.
– When the PTY mode that you have selected is
searched, searching will stop and the PTY mode will
be displayed.
– If there is no program in the PTY mode, you have
selected, searching will stop at the frequency started.
OPERATIONS
FM/AM TUNER ST6001
ANTETTA IF BAND FM
ON/STAMDBY
POWER
STANDBY
WIDE NARROW AB
RDS
TIMER SET
BAND
ON/OFF
FM MODE
PRESET
UP
DOWN
UP DOWN TUNING MEMONEXT CANCEL
TUNING
MODE /DISPLAY
ST.NAME
TIME ADJ.
TIMER
DAILY ONCE
TUNED STEREO RDS PTY PT TP TA
PRESET
kHz
MHz
CH
MEMO
!6
!4
i !0
ST6001N 01 Eng 06.1.20 10:34 AM ページ10