ESPAÑOL FRANÇAIS ENGLISH AV Surround Receiver SR7005
ESPAÑOL n SAFETY PRECAUTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
ENGLISH FRANÇAIS ESPAÑOL n NOTES ON USE / OBSERVATIONS RELATIVES A L’UTILISATION / NOTAS SOBRE EL USO WARNINGS AVERTISSEMENTS ADVERTENCIAS • Avoid high temperatures. Allow for sufficient heat dispersion when installed in a rack. • Handle the power cord carefully. Hold the plug when unplugging the cord. • Keep the unit free from moisture, water, and dust. • Unplug the power cord when not using the unit for long periods of time. • Do not obstruct the ventilation holes.
SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH Thank you for purchasing this Marantz product. To ensure proper operation, please read this user guide carefully before using the product. After reading them, be sure to keep them for future reference.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Features Accessories Check that the following parts are supplied with the product. q User guide................................................................................ 1 w Warranty card (for USA)........................................................... 1 e Warranty card (for CANADA).................................................... 1 r Power cord...............................................................................
SVENSKA Features Music data from an iPod can be played back if you connect the USB cable supplied with the iPod via the USB port of this unit, and also an iPod can be controlled with the remote control unit for this unit. M-XPort (Marantz-eXtension Port) Speaker terminal for front height channel The unit is equipped with dedicated front height channel speaker terminals on the rear panel. You can enjoy 7.1-channel playback using the front height channel and 7.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Simple version (Simple setup guide) Simple version Here, we explain the entire setup procedure, from unboxing the unit to using it in a home theater. The “Simple version” section provides the speaker installation, connection, and setup methods for the 7.1-channel system with surround back speakers. For the installing, connecting, and setup methods of speakers other than the 7.1-channel system (with surround back speakers), see page 50.
SVENSKA 1 2 3 4 5 This unit can perform 2.0/2.1 to 7.1-channel surround playback. This page provides the speaker installation procedure for the 7.1-channel playback using surround back speakers as an example. ITALIANO FRANÇAIS 2 Connect Speakers Carefully check the left (L) and right (R) channels and + (red) and – (black) polarities on the speakers being connected to the this unit, and be sure to interconnect the channels and polarities correctly. Connecting the speaker cables Peel off about 0.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Connect Blu-ray Disc player and TV Use only an HDMI (High Definition Multimedia Interface) cable that bears the HDMI logo (a genuine HDMI product). Using a cable without the HDMI logo (a non-genuine HDMI product) may result in abnormal playback. When outputting Deep Color or 1080p, etc., we recommend you use a “High Speed HDMI cable” or a “High Speed HDMI cable with Ethernet”for enhanced high-quality playback.
SVENSKA 1 Turn on the TV and subwoofer power. the TV input to the input of 2 Change this unit. 3 Press ON to turn on power to the unit. Power on 3 4 5 FRANÇAIS DEUTSCH ENGLISH 4 Set up speakers (Audyssey® Auto Setup) 1 2 3 4 5 The acoustic characteristics of the connected speakers and listening room are measured and the optimum settings are made automatically. This is called “Audyssey Auto Setup”.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Set up speakers (Audyssey® Auto Setup) 1 About setup microphone placement • Measurements are performed by placing the setup microphone successively at multiple positions throughout the entire listening area, as shown in GExample qH. For best results, we recommend you measure in six or more positions, as shown in the illustration (up to eight positions).
SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH Set up speakers (Audyssey® Auto Setup) STEP 2 Preparation 4 Speaker Detection Connect the setup microphone to the SETUP MIC jack of this unit. AUTO SETUP AUDYSSEY AUTO SETUP [1/6] Enter RETURN Cancel This screen provides the method for setting up 7.1-channel playback using surround back speakers. For the method of setting up speakers other than the 7.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Set up speakers (Audyssey® Auto Setup) STEP 4 STEP 5 Calculation STEP 6 Check Finish Store Unplug the setup microphone from Select “Store” and then press ENTER. Use ui to select the item you want the screen, use ui 11 On 12 14 15 the unit’s SETUP MIC jack. to check, and then press ENTER . to select “Next 1 Calculation”, and then press ENTER. ® 16 Set Dynamic Volume . STEP3 Save the measurement results.
SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH Parameter Check An error message is displayed if Audyssey® Auto Setup could not be completed due to speaker placement, the measurement environment, etc. If this happens, check the relevant items, be sure to take the necessary measures, then perform Audyssey Auto Setup over again. This function enables you to check the measurement results and equalizer characteristics after Audyssey Auto Setup.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS 5 Play back disc BD two times in a row 1 Press to switch an input source for a player used for playback. 1 3 4 5 When power is switched to standby Press STANDBY. the component connected to 2 Play this unit. GPower indicator status in standby modeH • Normal standby : Red • When “HDMI Control” is set to “ON” : Orange • When “Network Standby” is set to “ON” : Orange 3 Adjust the sound volume.
SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH Simple version Basic version Basic version Here, we explain the connections and basic operation methods for this unit. Basic version F Connections vpage 14 F Playback (Basic operation) vpage 26 F Selecting a listening mode (Surround mode) vpage 46 nnRefer to the pages indicated below for information on connecting and playing back the various media and external devices.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Connections Important information • Make connections as follows before using this unit. Select an appropriate connection type according to the components to be connected. • You may need to make some settings on this unit depending on the connection method. Refer to each description for more information. • Select the cables (sold separately) according to the components being connected.
SVENSKA NEDERLANDS Important information • Menu screen • Status display screen When the input source is switched When the volume is adjusted FRANÇAIS DEUTSCH ENGLISH About HDMI cables • When a device supporting Deep Color signal transfer is connected, use a cable compatible “High Speed HDMI cable” or “High Speed HDMI cable with Ethernet”. • When the ARC function is used, connect a device with a ”Standard HDMI cable with Ethernet” or “High Speed HDMI cable with Ethernet” for HDMI 1.4a.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Connecting an HDMI-compatible device Cables used for connections Audio and video cable (sold separately) HDMI cable • This interface allows transfer of digital video signals and digital audio signals over a single HDMI cable.
SVENSKA NEDERLANDS ITALIANO To listen to TV audio through this device, use the optical digital connection. ENGLISH • You can enjoy video and audio from a Blu-ray Disc. • Select the connector to use and connect the device. • For instructions on HDMI connections, see “Connecting an HDMI-compatible device” (vpage 15). Cables used for connections Video cable (sold separately) Video cable (Yellow) This connection is not required when a TV compatible with the ARC function (Audio Return Channel (HDMI 1.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL Connecting a DVD player NEDERLANDS SVENSKA Connecting a set-top box (Satellite tuner/cable TV) • You can enjoy video and audio from a DVD. • Select the connector to use and connect the device. • For instructions on HDMI connections, see “Connecting an HDMI-compatible device” (vpage 15). • You can watch satellite or cable TV. • Select the connector to use and connect the device.
SVENSKA NEDERLANDS ESPAÑOL ITALIANO DEUTSCH ENGLISH Connecting a digital camcorder • You can record video onto a video cassette tape. • Select the connector to use and connect the device. • When recording analog audio, use the analog connection. • For instructions on HDMI connections, see “Connecting an HDMIcompatible device” (vpage 15). Set this to change the digital input connector or component video input connector to which the input source is assigned.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL Connecting an iPod or USB memory device to the USB port You can enjoy music stored on an iPod or USB memory device. Cables used for connections To connect an iPod to this unit, use the USB cable supplied with the iPod.
SVENSKA NEDERLANDS FRANÇAIS DEUTSCH ENGLISH Connecting a record player • You can record audio on a CD or cassette tape. • Select the connector to use and connect the device. • When recording analog audio, use the analog connection. You can enjoy playing records.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Connecting an antenna Connecting a SIRIUS connector • This unit is a SIRIUS Satellite Radio Ready® receiver. You can receive SIRIUS® Satellite Radio by connecting to the SiriusConnect Home Tuner and subscribing to the SIRIUS service. • Plug the SIRIUS connector on the SIRIUS service. • Position the Home Tuner antenna near a south-facing window to receive the best signal. For details, see “Listening to SIRIUS satellite radio” (vpage 31).
SVENSKA Connecting an antenna the stand section 1 Put through the bottom of the loop antenna from the rear and bend it forward. Square hole Loop antenna Projecting part the stand. ITALIANO FRANÇAIS DEUTSCH ENGLISH Connecting a wireless receiver (RX101) By connecting a wireless receiver RX101 (sold separately) to this unit, you can receive and playback audio signals from other devices using the Bluetooth Communication Function. • Use a Bluetooth device that is A2DP compatible (vpage 111 “A2DP”).
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL Connect a device that has a multichannel output terminal • You can connect this unit to an external device fitted with multi-channel sound audio output jacks to enjoy music and video. • The video signal can be connected in the same way as a Blu-ray Disc player / DVD player (vpage 17 “Connecting a Blu-ray Disc player”).
SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH Cable (sold separately) Ethernet cable Modem Computer nnRouter When using this unit, we recommend you use a router equipped with the following functions: • Built-in DHCP server This function automatically assigns IP addresses on the LAN. • Built-in 100BASE-TX switch When connecting multiple devices, we recommend a switching hub with a speed of 100 Mbps or greater.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Playback (Basic operation) nn Selecting the input source (vpage 26) nn Adjusting the master volume (vpage 27) nn Turning off the sound temporarily (vpage 27) nn Playing a Blu-ray Disc player/DVD player (vpage 27) nn Playing a CD player (vpage 27) nn Playing an iPod® (vpage 28) nn Playing a USB memory device (vpage 29) nn Tuning in radio stations (vpage 31) nn Playing a network audio (vpage 35) Selecting a listening mode (Surround mode) (vpa
SVENSKA NEDERLANDS ESPAÑOL ITALIANO Important information Set the front speakers to be used Use VOLUME to adjust the volume. Press SPKR A/B. nn When the “Volume Display” setting (vpage 86) is “Relative” • Each time you press SPKR A/B, the front speaker setting will change as follows. GAdjustable rangeH ––– –80.5dB – 18.0dB GAdjustable rangeH 0.0 – 99.0 • The adjustable range may vary depending on input signal and channel level settings. You can also operate via the main unit.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Playing an iPod® You can play back both video, photo and audio. 1 Connect the iPod® to the USB port (vpage 20 “Connecting an iPod or USB memory device to the USB port”). ON to turn on power to the 2 Press unit. NET/USB twice to switch 3 Press the input source to “NET/USB”. SEARCH/INFO and hold it down for 2 seconds 5 Press or more to select the display mode. • There are two modes for displaying the contents recorded on the iPod.
SVENSKA Playing an iPod® Operation buttons uio p Function Cursor operation / Auto search (cue, ui) / Manual search (Press and hold, ui) Enter / Pause ENTER (Press and hold) Stop SEARCH (Press and release) Page searchz1 / Character searchz2 SEARCH (Press and hold) Remote / Direct mode switching Return Manual search (fast-reverse/fast-forward) 1 8 9 3 2 REPEAT RANDOM Playback / Pause Auto search (cue) Pause Stop Repeat playback Random playback TV POWER TV power on/standby (Default : Marantz) TV I
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Playing a USB memory device Playing files stored on USB memory devices the USB memory device 1 Connect to the USB port (vpage 20 “Connecting an iPod or USB memory device to the USB port”). 2 Press NET/USB twice to switch the input source to “NET/USB”. [1/8] favorite Internet Radio Media Server USB Flickr Napster Pandora 3 Press ui to select “USB”, then press ENTER or p. D&M1 D&M2 D&M3 Music1.mp4 Music2.mp3 Music3.m4a Music4.
SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH Important information nnAbout SIRIUS XM radio To listen to Satellite Radio, you’ll need to connect either a SIRIUS or XM Satellite Radio tuner (sold separately) to your satellite-ready receiver. Satellite Radio is available to residents of the US (except Alaska and Hawaii) and Canada. Family friendly packages are also available to restrict channels featuring content that may be inappropriate for children.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Tuning in radio stations nnChecking the SIRIUS signal strength and radio ID nnPresetting radio channels (Preset memory) STATUS until 1 Press “SIGNAL” appears on the in the broadcast channel 1 Tune you want to preset. 2 Press MEMORY. SHIFT to select the block 3 Press (A to G) in which to preset the display. The display will switch as shown below, depending on the reception conditions.
SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH Tuning in radio stations to the channel you want to 1 Tune lock. Press ENTER for at least 3 2 seconds. “Enter Lock Code” is displayed. When you enter the correct code, the corresponding channel is locked. 4 Press ENTER.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Tuning in radio stations nnSelecting audio programs HD Radio Technology enables stations to broadcast multiple Audio Program and data services on HD2 / HD3 / HD4 channels. Press ui to select the audio program. If the station you are listening to has multiple audio programs, “HD1” is indicated on the display. If it only has one audio program, “HD” is indicated.
SVENSKA Tuning in radio stations Operation buttons PRESET +, – uio p 0–9 SHIFT MEMORY TV POWER TV INPUT ITALIANO FRANÇAIS DEUTSCH ENGLISH Playing a network audio Follow this procedure to play Internet radio stations or music or still picture (JPEG) files stored on a computer. Important information Slide show function Still picture (JPEG) files stored in folders on a media server can be played as slide shows. The duration each picture is displayed can be set.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Playing a network audio Listening to internet radio GCompatible formatsH Sampling frequency Bit rate Extension WMA (Windows Media Audio) 32/44.1/48 kHz 48 – 192 kbps .wma MP3 (MPEG-1 Audio Layer-3) 32/44.1/48 kHz 32 – 320 kbps .mp3 WAV 32/44.1/48 kHz – .wav MPEG-4 AAC 32/44.1/48 kHz 16 – 320 kbps .aac/ .m4a/ .mp4 FLAC (Free Lossless Audio Codec) 32/44.1/48/ 88.2/96 kHz – .flac 1 Prepare for playback.
SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH Playing a network audio Preset Internet radio stations can be selected directly. 1 While the Internet radio station you want to preset is playing, press MEMORY. 1 – 8 to select the desired preset number. 4 Press MEMORY again to complete the setting. The Internet radio station is now preset.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Playing a network audio Playing files stored on a computer nnInternet radio operation Operation buttons PRESET +, – uio p ENTER (Press and release) Function Preset channel selection Cursor operation Enter ENTER (Press and hold) Stop SEARCH RETURN 2 1–8 SHIFT MEMORY Page searchz1 / Character searchz2 Return Stop Preset channel selection Preset channel block selection Favorites / Preset memory registration TV POWER TV power on/standb
SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH Playing a network audio Viewing photographs on the Flickr site Operation buttons PRESET +, – Function Preset channel selection You can view photographs shared by particular users, or all of the photographs shared on Flickr. uio p Cursor operation / Auto search (cue, ui) ENTER (Press and release) nnViewing photographs shared by particular users Enter / Pause SEARCH RETURN 1 8 9 3 2 1–8 Stop 1 Prepare for playback.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Playing a network audio nnViewing all photographs on Flickr 1 Prepare for playback. q Check the network environment, then turn on this unit’s power (vpage 25 “Connecting to a home network (LAN)”). w If settings are required, make the “Network Connecting” (vpage 83). 2 Press AMP and then press SOURCE SEL to display the Source Select menu, then select (vpage 26).
SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH Playing a network audio nnRegistering tracks in my Napster library The track is entered in the Library. want to listen to p. 1 Press SEARCH/INFO. ui to select the information 2 Use or track, then press ENTER. [1/8] Napster My Napster Library Napster Playlists Search by Track E Staff Picks • You can search by artist name, album name or track name. 2 Use ui to select the search item, then press ENTER.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Playing a network audio Listening to Pandora 1 3 Prepare for playback. q Check the network environment, then turn on this unit’s power (vpage 25 “Connecting to a home network (LAN)”). w If settings are required, make the “Network Connecting” (vpage 83). If you have a Pandora account, press ui to select “I have a Pandora account”, then press ENTER or p.
SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH Playing a network audio Listening to a created radio station (e.g. D&M2 Radio) By specifying your favorite track or artist name, music that has a similar rhythm or sound is chosen and streamed. nnArranging tracks within radio stations nnSign out Press p while a track is playing. the Pandora top menu is 1 While displayed, press RETURN. You can sort tracks by operating the Pandora menu screen while a track is playing.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Playing a network audio Listening to Rhapsody NOTE 1 Prepare for playback. q Check the network environment, then turn on this unit’s power (vpage 25 “Connecting to a home network (LAN)”). w If settings are required, make the “Network Connecting” (vpage 83). • The password should be no longer than 99 characters. • Press RETURN to cancel the input. When “Cancel input?” is displayed, select “Yes”, then press ENTER.
SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH Playing a network audio nnRhapsody operation Press p during playback to display the track menu. [1/6] Introduction Jamp to artist Add to my library Rating q w e q Search from the similar music Use ui to select the search item, then press ENTER or p. Use ui to select “Add to my library”, then press ENTER or p. The track is entered in the library. e Rating function Use ui to select “Rating”, then 1 press ENTER or p.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Selecting a listening mode (Surround mode) This unit can play input audio signals in multi-channel surround mode or in stereo mode. Select a listening mode suitable for the playback contents (cinema, music, etc.) or according to your liking.
SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH Multi-channel playback z3 This mode is for 7.1-channel, 6.1-channel or GViews on the displayH q q Shows a decoder to be w used. w Shows Audyssey DSX™ processing. nnSurround playback of multi-channel sources (Dolby Digital, DTS etc.) multichannel sound. • If SURROUND MODE on the main unit is pressed, the same function as with the remote control unit can be obtained.
ENGLISH DEUTSCH FRANÇAIS ITALIANO Stereo playback This is the mode for playing in stereo. The tone can be adjusted. • Sound is output from the front left and right speakers and subwoofer. • If multichannel signals are input, they are mixed down to 2-channel audio and are played. 1 2 Press STEREO. Playing the source (vpage 27 – 45). Stereo playback begins. ESPAÑOL NEDERLANDS SVENSKA nnDolby Headphone mode • To cancel, press P.DIRECT again.
SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH Simple version Advanced version Advanced version Here, we explain functions and operations that let you make better use of this unit.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Speaker installation/connection (Advanced connection) FHR FR FL SW C FWL z3 z1 At least 3.3 ft / 1 m SL Surround speaker Front wide speaker 4 Front height speaker • Point slightly downwards SR Listening position SBL 2 – 3 ft / z2 60 – 90 cm 45˚ Front speaker FWR z2 z1 Install the surround back speakers in a position 2 to 3 ft (60 to 90 cm) higher than ear level.
SVENSKA Install FL ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH Connect Simple version When 5.1ch installed NEDERLANDS • For the method of connecting the 7.1-channel system with surround back speakers, see page 5. • For the method of connecting the TV, see page 6. 7.1-channel (Surround back / Front height / Front wide speaker) connection FR SW For 7.1-channel (Surround back / Front height / Front wide speaker) playback, set “Set up “Amp Assign”” (vpage 54) to “Normal”.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Connect 6.1-channel (Surround back speaker) connection 5.1-channel connection If using only one surround back speaker (with a 6.1-channel connection), connect to the “L” side of the SURR. BACK/AMP ASSIGN terminal. For speaker settings in this case, see “When 6.1ch (Surround back speaker) installed” (vpage 50). For 6.1-channel (Surround back speaker) playback, set “Set up “Amp Assign”” (vpage 54) to “Normal”. For 5.
SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH Connect Bi-Amp connection NOTE When using the A front speakers and B front speakers simultaneously, make sure you check the impedance of the connected speakers (vpage 5). 2.1-channel connection A bi-amp connection is to connect separate amplifiers to the tweeter terminals and woofer terminals of speakers compatible with the bi-amp function.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Set up speakers around items indicate the settings. This section provides the setup methods of speaker systems other than the 7.1-channel system (with surround back speakers). For the setup methods of the 7.1-channel system with surround back speakers, see “Simple version”, “Set up speakers (Audyssey® Auto Setup)” (vpage 7) of “Simple version”. First install and connect the speakers to this unit.
SVENSKA Set up speakers Measure Set for measuring two surround back (2spkrs) speakers. Measure Set for measuring a surround back (1spkr) speaker. Set for no measuring of a surround back speaker. 9 Use o p to select the item. GWhen “Front Height” or “Front Wide” is selected in step 6H Measure Set to measure the front height speakers or front wide speakers. Skip Set when you do not want to measure the front height speakers or front wide speakers.
ENGLISH DEUTSCH FRANÇAIS ITALIANO RS-232C connector By connecting an external serial controller, you can control all sorts of household electrical devices (including lights, electric curtains, and air conditioning units) in addition to your audio and video devices. External serial controller ESPAÑOL NEDERLANDS SVENSKA DC OUT (TRIGGER OUT) jacks When a device with DC IN jack is connected, the connected device’s power on/standby can be controlled through linked operation to this unit.
SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH Playback (Basic operation) (vpage 26) Selecting a listening mode (Surround mode) (vpage 46) HDMI control function When you make an HDMI connection with a TV or player compatible with this unit and HDMI control functions, you can perform the following operations by setting the HDMI control function of each device. nn This unit power off can be linked to the TV power off step. nn You can switch audio output devices with a TV operation.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Convenient functions Sleep timer function Adjusting the volume of the speakers The power automatically goes into standby once the set time has elapsed. This is convenient for playing sources while going to sleep. You can adjust the channel level either according to the playback sources or to suit your taste, as described below. 1 Press AMP to set the remote control unit to amplifier operation mode.
SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH Convenient functions nnPlaying contents on a mobile terminal device • Perform this procedure using a wireless LAN-compatible mobile terminal conforming to the DLNA (Digital Living Network Alliance) standard. • This function allows you to play content located on a computer (media server) or mobile terminal device connected on a network by operating a mobile terminal device on the same network.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Convenient functions Web control function the top menu is displayed, click on the menu 4 When 5 Operate. item you want to operate. You can operate this unit using a browser. 1 the IP address of this unit with “Network 2 Check Information” (vpage 85). Switch the “Network Standby” setting to “ON”. (vpage 84). Marantz Web Controller SR7005 MAIN ZONE Status -25.
SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH Convenient functions SETUP MENU AUDIO/VIDEO ADJUST MANUAL SETUP INFORMATION SAVE LOAD Q1 1080p 1080p Q8 1080p:24Hz 1080p:24Hz Q8 Select this item to operate each zone.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Convenient functions Panel lock function nnCanceling the Panel lock function To prevent accidental operation of this unit, you can disable operation of the buttons on the front panel. ON/STANDBY i Various memory functions nnPersonal memory plus function This function sets the settings (input mode, surround mode, HDMI output mode, MultEQ® XT, Dynamic EQ®, Dynamic Volume®, audio delay etc.
SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH • You can operate this unit so as to enjoy audio in a room (ZONE2, ZONE3) other than the MAIN ZONE (room where the unit is located). • You can simultaneously play back the same source in both the MAIN ZONE, ZONE2 and ZONE3. You can also play back separate sources in the MAIN ZONE, ZONE2 and ZONE3.
ENGLISH DEUTSCH FRANÇAIS ITALIANO Video output NEDERLANDS SVENSKA Playback Z2 or Z3 to switch the 1 Press remote control operating mode. Video Connection The remote control unit switches to the operating mode for ZONE2 or ZONE3. The video signals of this unit’s ZONE2 video output terminal are played by the ZONE2 TV. MAIN ZONE This unit ESPAÑOL ON to turn on the ZONE2 2 orPressZONE3 power. ZONE2 VIDEO ZONE2 VIDEO IN The or display lights.
SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH Menu map For menu operation, connect a TV to this unit and display the menu on the TV screen. For menu operations, see the following page. Setting items 1. Audio/Video Adjust AUDIO/VIDEO ADJUST Detailed items Description Page Audio Adjust Picture Adjust Adjuts various audio parameters. Adjusts the picture quality. 75 79 Status Audio Input Signal HDMI Information Preset Channel Shows information about current settings.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Examples of menu and front display Below we describe typical examples of displays on the TV screen and on the set’s display window. Menu display Top menu display Front display Description q The menu items are displayed here. w The selected line is displayed here. The currently selected item is displayed on the display. Use ui to move to the item you want to set.
SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH Method • Operating with the remote control unit. • Select a character on the TV screen to input characters. Normal screen q Default w SHIFT a/A SEARCH Keyboard Default INPUT SETUP RENAME q BD w e Input ENTER Enter SEARCH Keyboard INSERT Insert RETURN Cancel DELETE Delete q Character input section w Guide for operation buttons r t 1 o p to set the cursor to the character you want 2 toUsechange.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL Inputting characters 1 SEARCH/INFO 2 Press displayed. SVENSKA Input Setup Display the screen for inputting characters (vpage 65 “Menu map”). Perform settings related to input source playback. • You do not have to change the settings to use the unit. Make settings when needed. Menu operation while a normal screen is AMP to set the remote control unit to amplifier operation 1 Press mode. 2 Press MENU. 3 Use ui to select the menu to be set or operated.
SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH Input Setup Preset Skip (vpage 69) Auto Preset (vpage 69) INPUT SETUP PRESET SKIP INPUT SETUP AUTO PRESET Block A Block Presets A1 FM 87.50MHz A2 FM 87.90MHz A3 FM 89.10MHz A4 FM 93.30MHz A5 FM 97.90MHz A6 AM 98.10MHz A7 AM 98.90MHz A8 AM 100.10MHz Start RETURN Return INPUT SETUP PRESET NAME Block A1 FM 87.50MHz A2 FM 87.90MHz A3 FM 89.10MHz A4 FM 93.30MHz A5 FM 97.90MHz A6 AM 98.10MHz A7 AM 98.90MHz A8 AM 100.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Input Setup Setting items Edit Lock Code Change the password. SIRIUS Setting details 1. Press ui to select “Edit Lock Code”, and then press p or ENTER. 2. Input current lock code (4 digits) using uio p, and press ENTER. 3. Input new lock code (4 digits) using uio p, and press ENTER. 4. Input new lock code (4 digits) again using uio p, and press ENTER. 5. Press ui to select “Execute”, and then press ENTER.
SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH Input Setup Setting details Setting items HDMI HDMI 1 / HDMI 2 / HDMI 3 / HDMI 4 / HDMI 5 / HDMI 6 Set this to change the HDMI None : Do not assign an HDMI input connector to the selected input input connectors assigned source. to the input sources. • At time of purchase, the settings of the different input sources are as shown below.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Input Setup Setting items Video Mode Make settings for video processing. BD SAT AUX1 DVD VCR GAME z TV z Video Convert The input video signal is converted automatically in conjunction with the connected TV (vpage 14 “Converting input video signals for output (Video conversion function)”). BD SAT AUX1 DVD VCR BD AUX1 TV 72 Auto : Process video automatically based on the HDMI content information. Movie : Process video normally.
SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH Input Setup Default settings are underlined. The input modes available for selection may vary depending on the input source. Setting items Input Mode Set the audio input modes for the different input sources. Change the display name of the selected input source. Setting items Rename Change the display name of the selected input source. Default The input source name is returned to the default setting.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL Input Setup Default settings are underlined. Make settings for playing back still picture images. Setting items Setting details ON : Display still picture images in a slide show. OFF : Display only the selected still picture image. NET/USB Interval Set the playback time per image. SVENSKA Audio/Video Adjust Still Picture Slide Show Make slide show settings.
SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH Audio/Video Adjust Setting items nnSurround Parameter Default settings are underlined. Height Gain Control the front channel volume. Setting details Low : Reduce the front height channel volume. height Mid : Front height channel sound is output with standard sound volume. High : Increase the front height channel volume. Adjust surround sound parameters. It may not be possible to set this item depending on the input signal.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Audio/Video Adjust nnAudyssey Settings Default settings are underlined. ® ® ® Set MultEQ XT, Dynamic EQ and Dynamic Volume . These can be selected after Audyssey® Auto Setup has been performed. For additional information on Audyssey technology, please see page 111.
SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH Audio/Video Adjust Setting details Setting items Heavy : Most adjustment to softest and loudest sounds. Medium : Medium adjustment to loudest and softest sound. Light : Least adjustment to loudest and softest sounds. OFF : Do not use “Dynamic Volume”. • is displayed when set to “ON”. Each time DYN EQ/VOL is pressed, the setting is changed as shown below.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Audio/Video Adjust nnManual EQ Default settings are underlined. Use the graphic equalizer to adjust the tone of each speaker. “Manual EQ” can be set when “MultEQ XT” setting (vpage 76) is “Manual” Setting items Setting details Adjust CH Correct the tone of each speaker. q Select the speaker tone adjustment method. All : Adjust the tone of all speakers together. L/R : Adjust the tone of left and right speakers together.
SVENSKA NEDERLANDS Audio/Video Adjust Default settings are underlined. DVD VCR SAT GAME AUX1 NET/USB TV . • This item can be set when the input source is BD • With input sources other than the ones above, this item can be set when “Video Select” is selected. In this case, the original input source settings are called out. • Can be set when the “Video Convert” setting (vpage 72) is “ON”. • “GAME” or “TV” can be set when “HDMI” (vpage 71) or “Component” (vpage 71) has been assigned.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Manual Setup Speaker Setup Default settings are underlined. Perform when setting the speakers manually or when changing settings made in Audyssey Auto Setup. • If you change the speaker settings after performing Audyssey Auto Setup, it will not be possible to select MultEQ XT, Dynamic EQ and Dynamic Volume (vpage 76, 77). • Manual Setup can be used without changing the settings. Please set if necessary.
SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH Manual Setup Speaker Config. (Continued) Setting details F.Wide : Set the presence and size of the front wide speakers. • Large : Use a large speaker that can adequately play back low frequencies. • Small : Use a small speaker that has inadequate playback capacity for low frequencies. • None : Select when the front wide speakers are not connected. Setting items Distance (Continued) NOTE NOTE Speakers set to “None” in “Speaker Config.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Manual Setup Setting items Setting details Crossover Frequency Set the maximum frequency of the bass signal output from each channel to the subwoofer. Set the Crossover Frequency to suit the bass reproduction capability of the speaker being used. Crossover : Set the crossover frequency. • 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz / 250Hz Advanced : Specify crossover frequency for each speaker.
SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH Manual Setup Standby Source Sets the HDMI input source to put into standby when the power is on. Last : This item is set at the last-used input source. HDMI1 / HDMI2 / HDMI3 / HDMI4 / HDMI5 / HDMI6 : Put the respective input source into standby. Power Off Control Links the power standby of this unit to external equipment.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Manual Setup Setting items Network Connecting (Continued) Setting details Setting items r Use i to select “Exit” and press ENTER. Setup is complete. • When connecting to the network via a Proxy server, select “Proxy” and press ENTER (vpage 84 “Proxy settings”).
SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH Manual Setup Other (Continued) Setting details Update Notification : Displays a notification message on this unit’s menu screen when the latest firmware is released with “Firmware Update”. The notification message is displayed for about 20 seconds when the power is turned on. Connect to broadband Internet (vpage 25) when using this function. • ON : Display update message. • OFF : Do not display update message.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Manual Setup Setting items Power On Level Define the volume setting that is active when the power is turned on. Mute Level Set the amount of attenuation when muting is on. Setting details Last : Use the memorized setting from the last session. – – – (0) : Always mute when power is turned on. –80dB – 18dB (1 – 99) : The volume is adjusted to the set level.
SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH Manual Setup GUI (Continued) Setting details Wall Paper : Set wallpaper to display in the background when playback is stopped, etc. • Picture : Set the background to a picture (Marantz logo). • Black : Set the background to black. Format : Set the video signal format to be output for the TV you are using. • NTSC : Select NTSC output. • PAL : Select PAL output.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Manual Setup Setting items Display Set the display on/off setting. Setting details ON : Display is always on. Display Auto OFF : Display is off except when showing the status display. Display OFF : Display is always off. Setting items Firmware Update Update the firmware of the receiver. This can also be set by pressing DISPLAY. Each time DISPLAY is pressed, the setting is changed as shown below. ON ON : Turn protection on.
SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH Manual Setup Simple version Notes concerning use of “Firmware Update” and “Add New Feature” Basic version • In order to use these functions, you must have the correct system requirements and settings for a broadband Internet connection (vpage 25). • Do not turn off the power until updating or upgrating is completed.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Information Items Show information about receiver settings, input signals, etc. Items Status Show information about current settings. Setting details nn MAIN ZONE This item shows information about settings for MAIN ZONE. The information displayed differs according to the input source.
SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH Remote control settings Simple version Other settings Switches light illumination on/off You can switch the lighting around the main display on or off. • The factory setting is “ON”. Basic version • When you connect a remote control receiver unit (purchased separately) to the REMOTE CONTROL IN terminal of this unit, use the following procedure to disable the remote sensor function of this unit.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Operating the connected devices by remote control unit Registering the supplied preset codes in the remote control unit enables you to operate devices made by other manufacturers. Operating AV equipment the input source select 1 Press button (vpage 26). The remote control operating mode switches as shown in the table below, and the mode name is shown in the remote control display.
SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH When preset codes are registered in the included remote control unit, it can then be used to operate any devices you have, such as DVD players or TVs made by different manufacturers. NOTE nnButtons used for operating the devices For details on operation with the remote control unit, see pages 29 – 45, 94. The following two methods can be used for registering the reset code.
ENGLISH DEUTSCH FRANÇAIS ITALIANO Registering preset codes Default settings for preset codes The devices shown below are registered for each input source button as default. Settings can be changed according to the devices to be used. 1 Press and hold down the input source select buttons for appliance to control and press SET until indicator blinks twice. ESPAÑOL NEDERLANDS SVENSKA Operating components The supplied remote control unit can control a component other than this unit.
SVENSKA Operating components TV POWER TV INPUT Function Power on/standby Switch channels (up/down) Cursor operation Enter Channel selection Clear the inputting TV power on/standby (Default : Marantz) Switch TV input (Default : Marantz) ITALIANO FRANÇAIS DEUTSCH ENGLISH Operating learn function • If the AV device is not a Marantz device, or if the device does not operate even when the preset code is registered, use the learning function.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Operating learn function Delete saved remote control codes Codes can be erased in three ways: by buttons, sources, and by all memory contents. nnDelete remote control codes for each button 1 Press and hold down SET and SOURCE SEL until the LEARN indicator blinks. 2 Press input source select buttons to select the input source you want to delete. The input source is shown in the remote control display.
SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH Recording macro operations NOTE The RETURN, uio p, ENTER, VOLUME +, – and CLR buttons cannot be recorded as macro operations. Checking recorded macro operations [Example] Checking the recorded macro operations to button “1” 1 [Example] Recording DVD playback operations to the number “1” button flashes in the LEARN indicator, MACRO indicator and remote control display.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Operating macro function Using macro operations [Example] Using the recorded macro operations to button “1” 1 Press the MACRO. 2 Press the number button (“1”) that you want to use. “MACRO” is shown in the MACRO indicator and remote control display. Macro operations recorded to number button “1” are performed one at a time. • The step number shown in the remote control display disappears after the step is performed.
SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH Simple version Information Information Here, we list various information related to this unit. Please refer to this information as needed.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Part names and functions GWith the door openH Front panel W2 W1 For buttons not explained here, see the page indicated in parentheses ( ). W0 Q9 W3 y u t W4 W5 Q8 W6 W7 W8 o Q0 Q1 i Headphones jack When the headphones are plugged into this jack, audio will no longer be output from the connected speakers or from the PRE OUT connectors.
SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH Simple version Display Sub Display Main Display Q6 Q5 Q4 Q3 Q2 Q1 Q0 o i u Basic version q w q Input signal indicators w Input signal channel indicators q w e When the power to this device is switched on, the surrounding area is lit blue. The settings can be changed so the light does not switch on (vpage 91 “Switches light illumination on/off”).
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Rear panel See the page indicated in parentheses ( ).
SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH q Display Q7 q Q8 Q9 W0 q w e r y Tuner mode (T.MODE) button············· (33, 88) W1 u W2 W3 o Q0 W4 W5 Q1 Q2 W6 W7 Q3 W8 W9 E8 E0 E9 R0 R1 R2 FM/AM band switching button (BAND)···· (33) W9 STEREO button············································ (48) E0 AUTO buttons································ (46, 62, 117) E1 MULTEQ® button········································ (76) E2 Audio delay button (A.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Remote control unit Inserting the batteries Operating range of the remote control unit q Remove the rear lid in the direction of the arrow and remove it. Point the remote control unit at the remote sensor when operating it. w Load the two batteries properly as indicated by the marks in the battery compartment. R03/AAA 30° 30° Approx. 23 ft /7 m e Put the rear cover back on.
SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories. Trademark information This product uses the following technologies: SIRIUS, XM and all related marks and logos are trademarks of Sirius XM Radio Inc. and its subsidiaries. All rights reserved. Service not available in Alaska and Hawaii.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Surround This unit is equipped with a digital signal processing circuit that lets you play program sources in the surround mode to achieve the same sense of presence as in a movie theater. Surround modes and parameters This table shows the speakers that can be used in each surround mode and the surround parameters adjustable in each surround mode.
SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH Surround Surround mode (vpage 46) NEO:6 Music mode only PRO LOGIC g/gx Music mode only Height Gain (vpage 75) Panorama (vpage 75) Dimension (vpage 75) C.Width (vpage 75) C.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Surround nnTypes of input signals, and corresponding surround modes This table shows the input signal that can be played in each surround mode. Check the audio signal of the input source then select the surround mode. Symbols in the table S This indicates the selectable surround mode. Input signal types and formats PCM Surround mode (vpage 46) DTS SURROUND DTS-HD MSTR DTS-HD HI RES DTS ES DSCRT6.1 DTS ES MTRX6.
SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH Surround Surround mode (vpage 46) LINEAR PCM LINEAR PCM (multi ch) (2ch) S S S S S z5 z2z3 z1z3 z4 z3 z3 DTS-HD High Resolution Audio DTS EXPRESS DTS ES DSCRT (With Flag) DTS ES MTRX (With Flag) DOLBY DTS (5.1ch) DTS 96/24 DOLBY TrueHD DOLBY DIGITAL DOLBY DOLBY DOLBY DIGITAL EX DIGITAL EX DIGITAL Plus (With no (With Flag) Flag) DOLBY DIGITAL (5.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Relationship between video signals and monitor output MAIN ZONE MONITOR OUT Video Convert Input Signals Output Signals Menu displayed 1 ON HDMI A COMPONENT A VIDEO A HDMI COMPONENT VIDEO HDMI Wall paper A A 2 OFF A A A A A A Only the menu is displayed 3 ON A A S VIDEO VIDEO VIDEO S (VIDEO) 4 ON A S (1080p) A A 5 ON A S (1080i ~ 480p) A A 6 ON A S (480i/576i) A 7 ON A S (1080p) S 8 ON
SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH A 111 Information B Bluetooth Bluetooth is a short-distance wireless communication technology used for connecting handheld devices several meters apart. This enables notebook computers, PDA s, mobile phones, etc. to connect without a cable for transmitting audio and data.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Explanation of terms Dolby Headphone The Dolby Headphone technology provides a surround sound listening experience over headphones. When listening to multichannel content such as DVD movies over headphones, the listening experience is fundamentally different than listening to speakers. Since the headphone speaker drivers are covering the pinna of the ear, the listening experience differs greatly from traditional speaker playback.
SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH Explanation of terms X x.v.Color This function lets HDTVs display colors more accurately. It enables display with natural, vivid colors. “x.v.Color” is a Sony registered trademark. Z ZONE2 This unit can operate in a room other than the room where this unit is placed (MAIN ZONE) (ZONE2 playback). The room for ZONE2 playback is called ZONE2.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Troubleshooting If a problem should arise, first check the following: 1. Are the connections correct? 2. Is the set being operated as described in the user guide? 3. Are the other components operating properly? If this unit does not operate properly, check the items listed in the table below. Should the problem persist, there may be a malfunction. In this case, disconnect the power immediately and contact your store of purchase.
SVENSKA NEDERLANDS DEUTSCH ENGLISH • Check the connection of the HDMI connectors. • When outputting HDMI audio from the speakers, set “HDMI Audio Out” on the menu to “AMP”. • When outputting HDMI audio from a TV, set “HDMI Audio Out” on the menu to “TV”. 16 82 • Check the connection of the HDMI connectors. • Set the input source to match the connected HDMI connector. • Check whether the TV is compatible with copyright protection (HDCP).
ENGLISH Symptom DEUTSCH FRANÇAIS ITALIANO ESPAÑOL Cause/Solution Page Server is not found, or it is not possible to connect to the server. • The computer’s or router’s firewall is activated. Check the computer’s or router’s firewall settings. • Computer’s power is not turned on. Turn on the power. • Server is not running. Launch the server. • Set’s IP address is wrong. Check the set’s IP address. – iPod cannot be played. • Some iPods do not support being used connected directly to the USB port.
SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH Simple version Resetting the microprocessor Perform this procedure if the display is abnormal or if operations cannot be performed. When the microprocessor is reset, all the settings are reset to their default values. Various setting details can be saved and reset on this device.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Specifications nn Audio section • Power amplifier Rated output: Maximum effective output power: Output connectors: • Analog Input sensitivity/Input impedance: Frequency response: S/N: Distortion: Rated output: • Digital D/A output: Digital input: nn Tuner section Front: 125 W + 125 W (8 Ω, 20 Hz – 20 kHz with 0.08 % T.H.D.) Center: 125 W (8 Ω, 20 Hz – 20 kHz with 0.08 % T.H.D.) Surround: 125 W + 125 W (8 Ω, 20 Hz – 20 kHz with 0.08 % T.
SVENSKA Index vvA vvC Cable Audio cable······················ 6, 17, 18, 19, 20, 21, 24 Coaxial digital cable·········································· 18 vvD D.
ENGLISH DEUTSCH FRANÇAIS Mute Level·························································· 86 M-XPort······························································· 23 vvN Napster·························································· 36, 40 Network Setup···················································· 83 Network Connecting········································· 83 Network Information········································· 85 Other···························································
List of preset codes / Liste de codes préréglés / Lista de códigos pre-ajustados Device select : BD Samsung Blu-ray Disc Player D H I J L M O P R S T Y Denon Hitachi Integra JWC LG Marantz Mitsubishi Onkyo Panasonic Philips Pioneer RCA Samsung Sharp Sony Toshiba Yamaha 5034, 5035, 5036 5031, 5032, 5033 5013 5014, 5015, 5017, 5018, 5019, 5020 5010, 5011 5000, 5026, 5027 5024, 5025 5013 5001, 5002, 5003 5004 5005 5012 5005 5028, 5029, 5030 5007, 5008, 5009, 5016 5012 5021, 5022, 5023 Device select : DVD
SAMSUNG SANSUI Device select : CD SANYO CD Player A C D E F G H I J K L M N O AIWA AKAI AUDIO AUDIO LABS CALIFORNIA CARVER CASIO CURTIS DENON EMERSON FISHER GE GENEXXA HARMON HITACHI INKEL JC PENNEY JVC KARDON KRELL LUXMAN LX I MAGNAVOX MARANTZ MATHES MCS MGA MISSION MITSUBISHI NAD NAKAMICHI NEC MCS NIKKO ONKYO OPTIMUS P PANASONIC PHILIPS PIONEER Q R QUASAR RCA REALISTIC S 2 ROTEL RS ORIGINAL SAE SCOTT 3001, 3002, 3003 3004, 3005, 3006 3007 3008 3008 3010, 3011, 3009 3012, 3020 3020, 3012 30
187.0 (7 3/8) 170.5 (6 3/4) 23.5 (15/16) 406.0 (16) 360.0 (14 3/16) 22.5 (15/16) Unit : mm (in) 16.5 (11/16) Dimensions / Dimensions / Dimensions 440.
D&M Holdings Inc.
