User`s guide

5
When the backlight is on, pressing the button will
prolong illumination of the display.

WARNING
Temperature can noticeably affect battery
voltage. The icon that signals a low battery
level may appear due to low temperatures,
even if the battery still has sufficient
capacity. In this case, backlighting is
disabled.
If backlighting has been disabled due to low
temperature, you can repeat the battery status
check by entering System mode.
If the battery icon disappears, the backlighting
function has been re-enabled.

WARNING
We recommend that you replace the
battery if you intend to dive in cold water.
AUTOMATIC SWITCHOFF
If Puck Air is turned on but no button is
pressed for a certain period of time, it will turn
off automatically. The delay before automatic
switch-off varies depending on the current
operating mode.
SETTING PARAMETERS FOR
THE PUCK AIR COMPUTER
ADJUSTING THE WATCH:
WATCHSET
The Watchset menu is divided into three
submenus, where you can adjust the following
parameters:
• Adj Time
- Time
- Watch display (12h-24h)
- Date
• Contrast
- Display contrast
• Set Beep
- Enable/disable the beep that sounds
when the button is pressed
• Intro
- Enable or disable the introduction
displayed each time Puck Air is
switched on
Scroll through the main menu and move to
Watchset (Figure 6).
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59
1
2
4
5
6
7
8
9
10
11
3
Fig. 6
To enter the Watchset menu, press and hold
the button. The words Adj Time will appear
(Figure 7).
•
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59
1
2
4
5
6
7
8
9
10
11
3
Fig. 7
WATCHSET  ADJ TIME
When the words “Adj Time” appear, press and
hold the button.
The minutes number will flash. Press the
button to increase the minutes (Figure 8).
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59
1
2
4
5
6
7
8
9
10
11
3
Fig. 8
Press and hold the button to save the current
minutes value.
The hour number will flash.
Change and set the number using the same
procedure as for the minutes.
In sequence, the information displayed is:
• minutes
• hour
• time format
• year
• month
• day
Setting the day returns you to the Adj Time
menu.
Press the button to move to the Contrast
menu.
WATCHSET  CONTRAST
Press and hold the button to enter this mode.
The current contrast value will flash (Figure 9).
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59
1
2
4
5
6
7
8
9
10
11
3
Fig. 9
Press the button to increase the contrast
(maximum value 6).
Press and hold the button to select the desired
value.
WATCHSET  SET BEEP
Press and hold the button to enter this mode.
The current value, “On” or “Off”, will flash
(Figure 10).
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59
1
2
4
5
6
7
8
9
10
11
3
Fig. 10
Press the button to change your selection.
Press and hold the button to confirm your
selection.
WATCHSET  INTRO
Press and hold the button to enter this mode.
The current value, “On” or “Off”, will flash.
Press the button to change your selection.
Press and hold the button to confirm your
selection.
Press the button to move to the Esc position
(Figure 11).
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59
1
2
4
5
6
7
8
9
10
11
3
Fig. 11
Press the button to return to the Watchset
menu.
Press and hold the button to exit this menu
and return to the main menu.
NOTE
The Esc position is available in all menus.
When you are in this position, if you press
the button, it takes you to the beginning
of the current menu. If you press and hold
the button, it will exit the current menu
and go back to the main menu.
ADJUSTING THE GENERAL DIVE
PARAMETERS: SET DATA
In this menu you can adjust the general dive
parameters selected.
• salt / fresh water
• degrees in Celsius – meters – bar /
degrees Fahrenheit – feet – psi
• clear residual nitrogen
Scroll through the main menu and move to
Set Data (Figure 12).
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59
1
2
4
5
6
7
8
9
10
11
3
Fig. 12