GAS TANKLESS WATER HEATERS INSTRUCTIONS MANUAL WINTER INVIERNO SUMMER VERANO GAS WINTER INVIERNO SUMMER VERANO GAS WINTER INVIERNO SUMMER VERANO GAS GAS GAS GAS POWER GAS MODEL WATER/AGUA WATER/AGUA WATER/AGUA
Congratulations! You've just purchased a new Marey POWER GAS tankless water heater and will soon begin enjoy the benefits of “going tankless”. FUNCTIONS AND FEATURES 04 CONSTRUCTION AND NAME OF EACH PART 05 PRECAUTIONS 07 INSTALLATION 09 Use this manual to guide you through the installation and operation, as it contains important safety tips and instructions.
1. Water-controlled automatic ignition: The water-controlled automatic ignition is provided through a double-ignition highrating device. The flame is sensed by ions. This sensitivity control makes it easy and convenient to operate. Flue duct type 2. Auto cut-off protection: The auto-cut-off protection will shut off the gas supply immediately if a flameout accidentally occurs, therefore preventing a gas leak. 3. Energy savings: The advanced combustion system comes with a Winter/Summer switch.
Forced exhausted type Technical parameters: 0.4 PSI NG 0.3 PSI 10-Layer Safety Protection Pulse Double Ignition 79,228 BTU/h Water Pressure Controlled POWER GAS 10L FE Wind-pressure valve Force Exhaust Type Power wire 16L/min 4.2Gal/min 10L/min 2.7Gal/min G1/2 Pipe LPG 111,903 BTU/h Cold Water Pipe Hot Water Pipe 0.3 PSI 10L/min 2.7Gal/min ø 0.37 inches / ø 9.5 mm Rubber Hose NG POWER GAS 16L Flue Duct Type Smog-collecting hood 79,228 BTU/h 5L/min 1.3Gal/min Gas Pipe 0.
1. Heater Installation A) Drill 8mm holes according to the dimensions shown on Drawing 7, and put in 6mm expansion screws (If the dimensions are different, please use those instead). B) Hang the water heater and secure it with the expansion screw at the hole in the lower bracket. See Drawing 8. Exhaust fan There must be an air inlet and an exhaust outlet Washer Nut Expansion screw Air inlet Heater Case (Drawing 4) (Drawing 7) (Drawing 8) 2. Pipe Installation A) Connect the cold water inlet pipe.
B) Connecting the hot water outlet pipe. Wind cap ŸThe hot water outlet joint is G1/2” threaded pipe. ŸThe hot water outlet should be connected by flexible metal tube or by rigid pipe. ŸThe inner diameter of the water outlet pipe (including the valve) shouldn´t be less than 8mm. Fix bracket Straight pipe Decoration board Bend connection C) After installation, fully open the cold water valve to test the flow of water and check whether there are any water leaks. Adjust or fix as needed.
1. Operations A) Open the cell box and put in correctly two D cell batteries. F) During operation, please pay attention to the combustion. If there is abnormal combustion, close the gas valve right away and contact the service center or gas company for maintenance. B) Open both the hot water and cold water valves. Close the water inlet valve after you make sure the cold water is flowing out through the water outlet and the ignition pins discharge.
1. Check the gas supply pipe (rubber house) regularly to see if it is in good condition. If its aging, cracked, leaking or bent. Troubleshooting 2. Check regularly to see if there are water or gas leaks. 3. Regularly clean the surface of the water heater to remove dirt or dust with a wet cloth, and then use a dry cloth to wipe off moisture. For hard to remove dirt, please use a neutral detergent to clean it. 4.
Marey Heater offers an excellent Customer Service. If you have any question about our product, need information about how to install a unit, about our Warranty Services, or if you want to share a suggestion, contact us! Please visit our website to get to know more about other Marey products. GAS PORTABLE POWER PAK SANTON AQUAMATIC MINI MAREY POWER GAS 1-877-727-0277 service@marey.