Owner’s Manual No500H Series Power Amplifier
FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug.
Mark Levinson Safety Terms & Symbols These terms may appear in this manual: Warning! Calls attention to a procedure, practice, condition or the like that, if not correctly performed or adhered to, could result in personal injury or death. Caution! Calls attention to a procedure, practice, condition or the like that, if not correctly performed or adhered to, could result in damage or destruction to part or all of the component. Note Calls attention to information that is essential to highlight.
Nº500H Series Power Amplifier Table of Contents Introduction............................................................................... 2 Product Description..................................................................... 2 What’s in the Box......................................................................... 2 Product Registration..................................................................... 3 Installation Considerations.........................................................
Mark Levinson Introduction Thank you for purchasing the Nº531H, Nº532H, Nº533H or Nº535H Power Amplifier. True to Mark Levinson® tradition, the audio excellence and performance levels of the Nº500H series amplifiers are unrivaled in today’s marketplace. Product Description The Nº500H series amplifiers redefine the concept of outstanding performance in their categories.
Nº500H Series Power Amplifier Product Registration Register your Nº500H series amplifier online at www.marklevinson.com within 15 days of purchase. Retain the original, dated sales receipt as proof of warranty coverage. Installation Considerations The Nº500H series power amplifier requires special care during installation to ensure optimal performance. Pay particular attention to instructions included in this section and to precautions included throughout this owner’s manual.
Mark Levinson DO allow at least 6 inches (15cm) of clearance behind the amplifier so that the power cord and cables have space to bend without becoming crimped or strained. DO NOT place the amplifier chassis on a thick rug or carpet or cover the amplifier with a cloth, as this might prevent proper cooling. DO NOT obstruct the ventilation holes on the top and bottom of the chassis or reduce airflow through the amplifier. DO NOT place the amplifier chassis near low-level components.
Nº500H Series Power Amplifier If this case occurs, consider installing a dedicated AC circuit for the system. Contact a licensed electrician for assistance. If more than one AC circuit is providing power to the system, contact a licensed electrician to ensure that all components are operating with the same solid, low-impedance ground reference.
Mark Levinson Front Panel The front panel contains one LED and one Standby button – as shown. Status LED standby Standby Button Standby Button Places the amplifier into Standby mode. Pressing the button while the amplifier is in Standby mode turns on the amplifier. 6 Standby mode powers only the low-voltage power supply, control, and communication circuits. Status LED Indicates the operating state of the amplifier and provides basic diagnostic information if a fault condition occurs.
Nº500H Series Power Amplifier Rear Panel The images below show a one-channel, two-channel, three-channel and five-channel rear panel view.
Mark Levinson Audio Channel Inputs One balanced and one single-ended (unbalanced) connector is available for each audio channel input. Single-Ended Inputs The RCA connectors accept single-ended signals from preamplifiers with singled-ended (RCA) outputs. A small toggle switch is provided to select either the balanced (XLR) or single-ended (RCA) input connector on each channel.
Nº500H Series Power Amplifier Banana plugs can also be used to connect the speaker cables to the loudspeaker binding posts. Banana plugs are not available on the 230 VAC model. Caution! DO NOT OVERTIGHTEN the binding posts. The innovative design of these binding posts provides more leverage; hence, high-contact, tight pressure connections are achieved when finger-tightened. DO NOT FORCE the binding post “wings” over a bent or oversized connector. Doing so may damage the binding post.
Mark Levinson Network Setup The Nº500H series power amplifier supports a network connection through the Ethernet port. The Nº500H series can connect to a network through use of a router or directly to a computer. The Nº500H series can be: 1. Connected to a router with DHCP active – We highly recommend using this option. Since the DHCP (Dynamic Host Configuration Protocol) automatically assigns the IP (Internet Protocol) addresses, setup is much simpler. 2.
Nº500H Series Power Amplifier Computer Requirements Note Connecting the Cables The PC-compatible computer used to connect to the Nº500H series must have the following software installed: • Windows® 2000 or Windows XP® • eb browser (Microsoft® Internet Explorer® 6.0 or higher W preferred) If DHCP is not active, the computer must be set up with a Static IP address. Refer to the “Setting Up the Computer” procedure found later in this section for instructions.
Mark Levinson Internal Web Page When connected to a computer, the Nº500H series has an internal Web page that provides access to: • etwork Setup – allows the user to modify the network setup N parameters. Accessing the internal Web page is the ONLY way to modify the network setup parameters of the Nº500H series amplifier. • tatus Information – provides basic status information of S the Nº500H series amplifier.
Nº500H Series Power Amplifier • ubnet Mask – identifies the subnet mask for the Nº500H S series. This IP address is automatically assigned by DHCP. If DHCP is off, then the address must be entered manually and must agree with the subnet mask address of the router. IP address 255.255.255.0 is the factory default value for the Nº500H series. • ost Name – indicates the network name given to the H Nº500H series amplifier.
Mark Levinson Setting Up the Computer Note If DHCP is not used, then the computer must be set up too. Use this procedure to set up the computer, then continue to the next procedure to connect to the amplifier. For the computer to find the amplifier, the LAN (Local Area Network) and TCP/IP (Internet Protocol) settings of the computer must be set up. The parameter setups vary slightly depending upon the operating system of the computer.
Nº500H Series Power Amplifier Network Setup for Windows 2000 1. From the Start menu, select Settings Control Panel. 2. Double-click on the Network and Dial-Up Connections option. 3. Double-click on the Local Area Connection option. 4. Click the Properties button to open the Local Area Connection Properties menu. If the computer is not currently connected to an active network, Step 3 has already opened the Local Area Connection Properties menu. 5.
Mark Levinson 3. S et up the router to the IP address 192.168.50.x – where x stands for a number other than 0, 3, 4, 5, 255, or the number used for the computer IP address. The router must be on the same subnet as the amplifier and the computer, but also must have its own unique address. Refer to the router’s owner’s manual for instructions on how to modify the IP address. 4. Press the Power button on the amplifier. 5. On the computer, open the Internet Explorer Web browser. 6.
Nº500H Series Power Amplifier Direct Connection Use this procedure to connect directly to a computer if you are not using a router. For the computer to find the amplifier, the TCP/ IP and LAN settings of the computer must be set up. Refer to the earlier “Setting up the Computer” procedure for instructions. 1. Connect the amplifier to the computer, as described in the earlier “Connecting the Cables” procedure. Make sure that both the amplifier and the computer are powered off before connecting. 2.
Mark Levinson ML Net The ML Net protocol allows you to control two or more Mark Levinson products simultaneously via the Ethernet port. Note Masters and Slaves Since ML Net operates through the use of a router and the Ethernet connection, all devices must have networking capability. Refer to the previous section of this manual, “Network Setup,” to set up the Nº500H series for network operation.
Nº500H Series Power Amplifier The figure below illustrates a typical ML Net setup: Nº532 Media Console (Master) Nº500 Series Power Amplifier #1 (Slave) Router Nº500 Series Power Amplifier #4 (Slave) Nº500 Series Power Amplifier #3 (Slave) Nº500 Series Power Amplifier #2 (Slave) Discovering Slaves Status Reporting Before the master device can control any slave device, the slave devices must be “discovered” and assigned to the master device.
Mark Levinson Troubleshooting Incorrect operation is sometimes mistaken for malfunction. If problems occur, use this section for troubleshooting information. If problems persist, contact your authorized Mark Levinson dealer. No Power 1. E xamine the power cord to ensure that it is connected to both the rear panel connector of the amplifier and an electrical outlet. 2. Make sure the amplifier is powered on with the Power switch. 3. Make sure the amplifier is not in Standby mode.
Nº500H Series Power Amplifier No Response to Commands in ML Net 1. Verify that the master device and the Nº500H series amplifier are properly connected together with a router. 2. Verify that the Nº500H series amplifier’s network setup is correct. Access to the internal Web page via a computer is required to verify the network settings of the Nº500H series. No Connectivity Via Ethernet • erify that the network cables are properly connected between V the router, switch, or hub and the amplifier.
Mark Levinson Fault Protection The Nº500H series is designed to prevent damage to themselves and associated components. These extensive features protect both the critical circuitry of the amplifier itself and shield connected loudspeakers from serious damage due to high-power levels. Basic protections designed into the Nº500H series include fuses on each amplifier channel to protect against excessive current conditions, such as driving shorted outputs.
Nº500H Series Power Amplifier Restoring Factory Defaults Pressing the Factory Default button on the internal Web page of the amplifier resets all settings to their factory default values. If the internal Web page is not available, there is also a key press sequence available. Follow the instructions below to reset the factory default settings from the front panel. 1. Power off the amplifier. 2. Press and hold the Standby button. 3. Press the Power button to turn on the power. 4.
Mark Levinson Nº531H, 532H, 533H Specifications All specifications are subject to change without notice. Input & Output Connectors Control Connectors 24 • one balanced XLR input per channel • one unbalanced RCA input per channel • one pair “Hurricane” loudspeaker outputs with banana-plug sockets per channel (banana-plug socket not available on the 230 VAC models) • one Ethernet 10Base-T port • one 3.5mm mono (tip/sleeve) mini plug trigger input, 3-12Vdc • one 3.
Nº500H Series Power Amplifier Nº535H Specifications All specifications are subject to change without notice. Input & Output Connectors • five balanced XLR inputs per channel • five unbalanced RCA inputs per channel • five pairs loudspeaker outputs with banana-plug sockets per channel (banana-plug socket not available on the 230 VAC models) Control Connectors • one Ethernet 10Base-T port • one 3.5mm mono (tip/sleeve) mini plug trigger input, 3-12Vdc • one 3.
Mark Levinson Declaration of Conformity Application of Council Directive(s): 2004/108/EC and 2006/95/EC, as amended. Standard(s) to Which Conformity Is Declared: EN 55013:2001 + A1:2003 + A2:2006 EN 55020:2007 EN 61000-3-3:1995 + A1:2001 + A2:2005 EN 60065:2002 Manufacturer: Harman International 1718 W. Mishawaka Road Elkhart, IN 46517 The equipment identified here conforms to the Directive(s) and Standard(s) specified above. Type of Equipment: Power Amplifier Models: Mark Levinson No.