v. 08.november.
IMPORTANT SAFETY INSTRUCTIONS 1) Read these instructions; 2) Keep these instructions; 3) Heed all warnings; 4) Follow all instructions; 5) Do not use this apparatus near water; 6) Clean only with dry cloth; 7) Do not block any ventilation openings.
FRONT PANEL PANNELLO FRONTALE 1) INPUT Connect your bass guitar to this input using a standard ¼” shielded instrument cable. 2) PAD This switch pads the input (1) at -6dB, 0dB, +6dB, or +12dB to compensate for higher output sources, such as basses with high-output pickups or active electronics. 3) SOLID STATE – TUBE - VINTAGE Push these buttons to select the AMP models for each AMP slot. 4) MUTE / TUNER This button allows you to access the chromatic tuner and the mute feature.
marked by the last two presses of the ENTER button. The display of the TAP TEMPO through the RECALL led is only possible if it is allocated and active a DELAY effect within the SLOT. 23) ON/OFF This switch delivers AC power to the unit. Make sure the unit is grounded; all three terminals of the AC power plug must be connected to avoid any injury to the user or damage to the unit. Bass Multiamp is manufactured to be used in the country where it has been sold and is factory preset to that country’s voltage.
UNBALANCED LINE OUT Unbalanced stereo output to connect to an external power amp (PRE OUT) 35) LEFT/MONO PRE out left channel (for mono connection use this output). 36) RIGHT PRE out right channel. 37) USB port (for service/maintenance). sbilanciate stereo per finale esterno (PRE OUT) 35) LEFT/MONO PRE out Left. Questa uscita deve essere usata nel caso di collegamento in mono. 36) RIGHT PRE out Right. 37) USB Uscita per collegamento USB (esclusivamente per service) MIDI 38) MIDI IN. 39) MIDI THRU.
BASS MULTIAMP S (stereo version) Select AMP MODE, press ENTER and select STEREO mode, MONO BRIDGE or BI-AMP mode. The MONO/BRIDGE, STEREO or BIAMP mode is not related to the PRESET. PRESET and MEMORY The Bass Multiamp features 8 memory BANK (BASS MULTIAMP S) or 7 memory BANK (BASS MULTIAMP), each one with 128 PRESETS subdivided in 3 FACTORY PRESETS Banks for BASS MULTIAMP S (2 FACTORY PRESETS Banks for BASS MULTIAMP) and 5 USERS Banks.
B-DRIVE 21 T-CHORUS MB CH/FL NINETHY PHASE REVERB DELAY VOLUME PEDAL NOISE SUPPRESSOR SEND/RETURN PAR EQ MW OCTAVER SUPER SYNTH COMPRESSORE ENV FILTER An asterisk (*) near the name signals the selected effect for the current slot. The SLOT ON/OFF button enable/disable the SLOT. AMP MODEL The first thing to do is to put the AMP you choose in the preferred SLOT.
If the AMP is already selected in one of the SLOT, to have access to its parameters (if featured in that model), go to SLOT AMP using the buttons and press ENTER.
Standard 151HR Standard 152HR New York 122 New York 804 Traveler 121H Standard 151HR Standard 152HR New York 122 New York 804 Traveler 121H Press EXIT to go back from the CAB menu. Premere EXIT per uscire dal menu’ CAB. Equalize the sound as for your personal preference. Equalizzare il suono. Now we’ll add the Compressor in the 1st SLOT. Select the 1st SLOT (enable it with the SLOT ON/OFF button, if it is disabled), press SLOT SELECT and select the COMPRESSOR, then press ENTER.
effect processor output. Select a SLOT, pressing SLOT SELECT and go to SEND/RETURN in the SLOT menu using the scrolling buttons. Press ENTER to confirm, now the outboard effect is enabled, press ENTER to access to the Send/Return parameters. Level – Signal Level Mode – Serial/Parallel Press EXIT to go back. OTHER POSSIBLE BASS MULTIAMP CONNECTIONS USE THE BASS MULTIAMP AS EFFECT PROCESSOR CONNECTED TO AN AMP HEAD’S SEND/RETURN.
SYSTEM MENU’ FILE STORE TO SD RECALL FROM SD EXPORT PRESET IMPORT PRESET DELETE PRESET SD FORMAT AMP MODE (BASS MULTIAMP S) STEREO MONO (BRIDGE) BI-AMP MIDI MIDI ADDRESS PRESET/PATCH MAP CONTROL CHANGE MAP FIRMWARE UPDATE BALANCED DI DI PATH END OF CHAIN POST AMP EQ PRE AMP EQ DI LEVEL FILE Use this menu to STORE and RECALL in the banks and single PRESET.
TECHNICAL SPECS Channels: Controls: EQ Controls: SOLID STATE / TUBE/ VINTAGE Gain – Phone Level - Master LOW - MID LOW - MID HIGH - HIGH Speaker Outputs: Bass Multiamp Bass Multiamp S Two ¼” Jack mono out and One Neutrik Speakon/¼” Jack Combo 4/16 ohm Two ¼” Jack mono out L/R (Stereo Mode) One Neutrik Speakon/¼” Jack Combo 8 ohm (Bridge Mode) Power Output: Bass Multiamp Bass Multiamp S 500W@4ohm / 300W@8ohm 500W + 500W @ 4ohm, 300W + 300W @ 8ohm, 1000W@8ohm (BRIDGE mode) Other Features: . . .
LIMITED WARRANTY Markbass offers an international limited warranty on Markbass products purchased from any authorized Markbass dealer, effective from the day of purchase. The terms of this warranty vary from country to country; please contact the Markbass distributor in your country for details. Please register this product online at www.markbass.it to establish the date of purchase.
WARRANTY CARD We’d like to thank you for choosing a Markbass product. If any problem occurs, please don’t hesitate to contact our support team at service@markbass.it. You can fill out this form and send a copy to Markbass (Parsek srl, Via Po 52, 66020 San Giovanni Teatino, CHIETI ITALY) or, even better, you can now register your warranty online in a matter of minutes, using our online registration form at www.markbass.it. Simply point, click and type in your information...
NOTE 13
Product specifications are subject to change without notice Italy - 66020 San Giovanni Teatino (Ch) - Via Po, 52 - Tel. +39 085 446 3755 - Fax +39 085 440 7764 www.markbass.it - info@markbass.