Electric Heater User Manual

ManualsBrandsMarley Engineered Products ManualsElectric HeaterC2500

Electric Baseboard Heaters

1800, 2500, C1800 & C2500 Series

WARNING

Installation & Maintenance Instructions

Dear Owner,

Congratulations! Thank you for purchasing this new heater manufactured by a division of Marley

Engineered Products. You have made a wise investment selecting the highest quality product in the heat-

ing industry. Please carefully read the installation and maintenance instructions shown in this manual.

You should enjoy years of efficient heating comfort with this product from Marley Engineered Products...

the industry’s leader in design, manufacturing, quality and service.

... The Employees of

Marley Engineered Products

Read Carefully - This Instruction Sheet contains vital

information for the proper installation, use, and efficient

operation of the heater. Carefully read the manual before

installation, operation, or cleaning of the heater. Failure to

adhere to the instructions could result in fire, electric

shock, death, serious personal injury, or property damage.

Save these instructions and review frequently for continu-

ing safe operation and instructing future users.

1. Keep all electrical cords, foam filled articles, drapes, bed-

ding, and other household furnishings away from contact with

heater. It is recommended all items be kept a minimum of

six (6") inches (152mm) from heater.

2. Do not install baseboard heater below electrical convenience

receptacles (outlets).

3. Do not install baseboard heater against vinyl wallpaper,

paperboard or low density fiberboard surface. Do not install

vinyl drapes or vinyl blinds above heater.

4. Do not recess heater in wall.

5. The installation must comply with applicable Local and National

Electrical Codes and utility requirements.

6. Do not remove or by-pass thermal cutout.

7. To reduce the risk of fire, do not store or use gasoline or

other flammable vapors and liquids in the vicinity of the

heater.

8. Personal injury or death could result from electric shock.

Disconnect all power to heater at main panel before attempting

to install or service this heater.

9. Supply voltage must be the same as heater voltage. Check

heater nameplate and supply voltage before energizing.

10. When using RSA Transformer Relay Accessory, supply

wiring must be suitable for 90°C.

File #E37116

Summary of content (4 pages)

PAGE 1
File #E37116 Electric Baseboard Heaters 1800, 2500, C1800 & C2500 Series Installation & Maintenance Instructions Dear Owner, Congratulations! Thank you for purchasing this new heater manufactured by a division of Marley Engineered Products. You have made a wise investment selecting the highest quality product in the heating industry. Please carefully read the installation and maintenance instructions shown in this manual.
PAGE 2
pole thermostat accessory is available for installation into this heater at your place of purchase, or the heater may be connected to any suitable wall mounted thermostat that will meet the electrical load requirements. Installation or use of this product in any manner not described herein will void the warranty and could result in injury, damage to property, or permanent damage to heater. Heater Ampere Rating. 208 Volt 240 Volt 277 Volt 347 Volt 600 Volt Residential Model No. Commercial Model No.
PAGE 3
NOTE: Make sure the caution label with the word “TOP” is at the top of the heater. For most efficient operation locate heaters along outside wall under windows. Position heater so it can be secured to wall stud. Power cable must enter heater through one of the knockouts provided in wiring compartment. See Figure 3. ! CAUTION When using bottom mounting holes, (to prevent a possible shock or fire hazard,) make sure you do not drive the screws through or damage the power supply wire. 7. 6.75 (153,2) 8.
PAGE 4
1. 2. 3. OPERATION After the baseboard system has been completely installed, all thermostats should be turned to LOW or NO HEAT. Then turn on breakers. Wait 3 to 5 minutes and check to see that none of the heaters are operating. If operating, disconnect power and check wiring. If none are operating then turn thermostats to highest position and wait 3 to 5 minutes. Check to see that all heater(s) are operating. Should any not be operating, disconnect power and check wiring.