Easy Icon Easy Icon 10 RF ™ Universal IR/RF remote with X-10 functionality USER MANUAL 3 GEBRAUCHSANLEITUNG 17 GUIDE UTILISATEUR 33 MODO DE EMPLEO 51 MANUALE D’ISTRUZIONI 67 GEBRUIKSAANWIJZING 83 20281/ 20080903 • EASY ICON 10 RF™ ALL RIGHTS RESERVED MARMITEK ©
The most user-friendly remote control ever. SAFETY WARNINGS • • • • • • • To prevent short circuits, this product should only be used inside and only in dry spaces. Do not expose the components to rain or moisture. Do not use the product close to a bath, swimming pool etc. Do not expose the components of your systems to extremely high temperatures or bright light sources. In case of improper usage or if you have altered and repaired the product yourself, all guarantees expire.
HOW DOES MARMITEK X-10 WORK? Marmitek X-10 components use the existing mains wiring to communicate (using Marmitek X-10 signals). You can build a complete system using the three different kind of components of the Marmitek X-10 System: 1. Modules: These components will receive Marmitek X-10 signals and will switch or dim the attached lamp or appliance. Examples of these modules are lamp modules and appliance modules. These are available as build-in, micro, DIN rail and plug-in modules. 2.
Known devices which can cause attenuation are: PC Monitors PCs with heavy internal power supplies Old Televisions Copiers Fluorescent Lights Gas Discharge Lamps (Energy Saving Lamps) 3. Some (old) devices are able to disturb the signal by transmitting noise on the power line. Because the Marmitek X-10 signals are transmitted on 120 kHz, only noise on or near this frequency will have influence on the range. When you use a FM10 Filter to connect this device to the power line, the noise will be filtered. 4.
INSTRUCTIONS FOR USE USING THE WIZARD After you insert the batteries and choose “English,” the Setup Wizard screen appears. You can exit the Wizard at any time by pressing the HOME key (located just below the screen). Follow the instructions on the Wizard screens to familiarize yourself with the OK, Back, and Side Keys. You can go back and forth through the Wizard, but once you’ve set up your devices and quit to save the settings, you won’t see the Wizard again unless you do a Master Reset.
SETTING FAVOURITES Once you’ve gone through the Wizard and set up at least a TV, and set up more devices, or skipped the rest of them, you arrive at screen shown to the right. When you press any digit key, say digit 4, to enter a channel number, you go to a screen where you can enter more digits if desired. The channel number can include a dash (-) for digital channels, e.g., 2-3, or can include ENTER, or OK, if your device requires it to change channels, e.g.
Favourites that you just set up, either in group or group. Selecting takes you to a screen showing that you now have CNBC set as the first Favourite in Group, as well as any other Favourites that you’ve set up. When you’re finished setting up Favourites, press the HOME button to go back to the Home screen. WORKING WITH FAVOURITES At any time, you can press the FAVOURITES key and select either the or Side Keys; or, you can press the or buttons on the remote to go to your Favourites screen.
LEARNING For the EasyIcon10RF to learn from another remote, do the following: • Place the 2 remotes on a flat surface (table). • Ensure that the transmitter end from the original remote is 40 mm or so away from the receiving end (bottom) of the EasyIcon10RF. • Press the key/button on the original remote that you want to learn from for about a second and release it (press and release). • Do not press and hold it for an extended period of time.
You can continue learning more individual keys by following the instructions on the screen, and then press Done when you’re finished. POWERMID XL AND XS The Marmitek Powermid XL allows you to extend the distance you can use your remote! You will be able to hide your IR sender from sight, and still operate your TV or other electronic devices through entertainment centers, cabinet doors, from another room, etc.
SETTING UP MARMITEK X-10 Setting Up the EASYICON10RF to operate the TM13 Transceiver using Housecode “B.” The TM13 Transceiver receives RF signals to control lights and appliances. Do the following to setup this transceiver. • Press the HOME key to display the setup screen. Select Setup. • Select X-10. • Select Add/Edit at the next screen. • Choose the room where you will locate the TM13. For this example choose Basement. • Press the Side Key to select. • At the add an X-10 device screen, press OK.
• the Basement.) Press the Side Key for the icon to operate the device. You can turn it on, dim, or off. (Note: Many devices have follow-up screens, which also provide additional features for operating the device. Use the Side Keys and Navigation buttons to operate those features.) QUICKPOWER FOR MARMITEK X-10 DEVICES • • • • • • Set up an Marmitek X-10 device using the Wizard or Add-Edit mode, for example a light in your Living Room with an LM12 module. Select Home/Setup/X10/More/QuickPower Macro.
• • • At the “add an X-10 device!” screen, press the OK key. Use the Side Key to Pick Device. Press the Security Side Key. Press the Side Key to select the SC9000. At the Security Options screen, press the Side Key to Set Password. Enter your 4-digit security code using the alphanumeric keys (This is your choice; do not forget your security code.) Press the Side Key for the Set Console Link.
• VOL up and down operates bright and dim if applicable. You can press the Side Key next to the module you wish to operate and toggle an “On” or “Off” function as well. MACROS Macros allow you to combine a number of commands, including time delays, by using a single key press. • Press the Home key. • At the screen shown, press the Side Key for Macros and press OK to access the first time Macro’s Wizard. • Press the Pick Module Side Key.
Am I able to increase the range of my remotes by using more Transceivers? Yes, you can use more than one TM13 Transceiver in your home when the range of your remotes is not sufficient. The TM13 is using so called collision detection to prevent signals to be disturbed when more than one TM13 is transmitting. TM13’s will wait for a quite power line before transmitting their data.
TECHNICAL DATA Hardware LCD display: Display Colours: Surface Luminance: IR frequency range: RF frequency: Dimensions: Software Protocol Code library: Symbol library: Macros: Learn function: for code library: Languages: Functions: Power Operating current: Operating current: Standby current: Power: 176 * 220 pixel with back light 65536 150 cd/ m2 30-70 kHz 433.
