Owner`s manual

M A R Q U I S S P A S
®
OWNER’S MANUAL
left corner of the panel display and the hour will begin flashing. Follow above
procedures to set the correct hour and minutes.
NOTE: When in a filter cycle, the Filter Cycle LED will illuminate.
Filter Cycle 2:
Press SETTING pad to enter filter 2 programming mode. “Program Filter 2 start
time” will be shown in the upper left hand corner of the panel display and the
hour will begin flashing. Follow above procedure to set the correct hour and
minutes. Press the SETTING pad again and “Program filter 2 end time” will be
shown in the upper left corner of the panel display. Follow above procedure to
set correct hour and minutes.
Spa Light:
Press SETTING pad to enter spa light programming mode. The light icon will
begin flashing at the bottom of the panel display. “Start time” will be shown in the
upper left hand corner of the panel display and the hour will begin flashing.
Follow above procedure to set the correct hour and minutes. Press the
SETTING pad again and “end time” will be shown in the upper left corner of the
panel display and the hour will begin flashing. Follow above procedure to set the
correct hour and minutes. Press the CLOCK pad to exit the programming mode.
NOTE: Any time during the setting of features, you may exit the programming
mode by pressing the CLOCK pad. If you do not want to run the spa light cycles,
set the start and end times for the same time.
HEAT MODE
Your spa comes preset in the Standard heat mode. Allow about one hour per
0.56°C for heating your spa water when increasing the temperature to the
desired level. The heat mode can be adjusted to one of three different settings:
Standard Mode
The spa water heats as necessary to maintain the set temperature. “Standard”
will display until the mode is changed.
NOTE: The last measured temperature displayed is current only when Pump 1
has been running for at least two minutes.
Economy Mode
In this mode the spa only heats to the set temperature during a filter cycle. The
“Economy” icon will display until the mode is changed. Press the JETS 1 pad to
put the spa in “Standard-in-Economy” mode which operates the same as
Standard mode (both Economy and Standard will display). The spa reverts to
Economy mode automatically after one hour.
Sleep Mode
The spa water heats to within 7°C of the set temperature only during filter
cycles. “Sleep” will display until the mode is changed.
To Adjust Heat Mode
First press the SETTINGS pad. The current heat mode will start flashing. Use
the TEMP- pad to scroll through the modes. When desired mode is displayed,
touch the SETTINGS pad again to lock the mode.
Panel Lock
Press TEMP+ or TEMP- pad followed by QUIET SOAK pad to lock. Then press
TEMP+ or TEMP- pad followed by QUIET SOAK pad to unlock.
• Lock feature locks all user settings: time, filter cycles, heat modes,
SmartClean™ and temperature settings.
• Lock feature does not lock Jets 1, Jets 2, Timer, Spa Light, Quiet Soak, or
Clock.
• Secured LED will illuminate when system is locked.
Quiet Soak
Press the QUIET SOAK pad to enter the soak mode. All automatic functions
related to the pumps are disabled (i.e., filter cycles, SmartClean™ cycles). If
either pump 1 or pump 2 are operating, they will be turned off. Soak mode lasts
for 30 minutes, then the spa returns to normal operation. All button functions
operate as normal while in a Soak mode. When in a Soak mode, the Soak LED
will illuminate.
Maintenance Reminders
• rSA will be displayed in the LCD window every 21 days.
• Clean Filter LED will illuminate every 30 days. rCL will be displayed in the LCD
window.
• Change Water LED will illuminate every 90 days. rCH will be displayed in the
LCD window.
• rCA will be displayed in the LCD window every 90 days (see LCD Diagnostic
Messages).
• To reset maintenance reminders, press SETTINGS pad. (See USER
PREFERENCE SETTINGS to suppress maintenance reminders.)
JETS
Use JETS 1 pad on either bather’s panel or remote control. First press JETS 1
pad to activate pump on low-speed. Second press of JETS 1 pad activates
pump on high-speed. Third press of JETS 1 pad turns jets off for all-quiet soak
setting. Fourth press of JETS 1 pad returns pump to low-speed. Repeat above
procedure for JETS 2 and JETS 3.
Pump 1 and 2: Epic and Show
• High-speed run timeout: 15 minutes
• Low-speed run timeout: 15 minutes (if not in filter cycle or SmartClean™).
CONSTANTCLEAN™ WATER MANAGEMENT WITH BUILT-IN SANITATION
SYSTEM Not available in all international markets. (See Built-in Sanitation
System)
Ozonator Operation
The ozone generator operates when pump 1 is on low-speed in Filter Cycles
and SmartClean™ cycles ONLY. The O3 icon appears to the left of the
temperature display when the ozone generator is operating.
User Preference Settings
Suppress reminders: Displayed as (Sr.n) for no, and (Sr.Y) for yes. When set
to (Sr.Y), reminders are never shown in the display. When set to (Sr.n), all
reminders are shown.
Temperature display in Celsius: Displayed as (tc.n) for no, and (tc.Y) for yes.
24 hour time: Displayed as (24.n) for no (12 hour AM/PM), and (24.Y) for yes
(24 hour military).
SmartClean™ settings: Displayed as (cc.0) for SmartClean off, (cc.1) 1 hour,
(cc.2) 2 hour, (cc.3) 3 hour, and (cc.4) for 4 hour Smart Logic durations. When
the spa is in a SmartClean cycle, the SmartClean LED will illuminate.
To Enter the User Preference Mode
• Press the TEMP+ button
• Press the JETS 1 button (displays (Edt))
• Press the LIGHTS button (displays (USr))
• Press the JETS 1 button (displays (Sr.n))
• Use TEMP + or TEMP– pad to scroll through options
- Sr.n: Reminders not suppressed
- tc.n: Temperature display not in Celsius
- 24.n: 12 hour AM/PM
- cc.1: One hour Smart Logic
• Once the desired selection has been reached, press the JETS 1 pad. The last
number or letter will flash. Use the TEMP + or TEMP– pad to change the setting.
Press the JETS 1 pad to enter selection and return to previous mode.
• Press the LIGHTS pad twice to return to normal operation.
• At any point, if a pad is not pressed within thirty seconds of a previous pad
press, the mode will cancel and the spa will return to normal operation.
WISH AUXILIARY LOUNGE CONTROL
Auxiliary panel controls the jets and lights. (See SPA CONTROL OPERATION
in the Owner’s Manual.)
REMOTE CONTROLS
(See OPERATING YOUR SPA, Light, and Jets.)
NOTE: During times of inactivity, wireless remotes should always be stored in
the cup holder on the lip of the spa or removed from the spa. By storing the
wireless remote out of water, the remote will be less susceptible to water
intrusion, a situation that can occur after extended water exposure. More often,
water intrusion occurs when spa owners attempt to replace the batteries in their
remote and then do not properly reseal the remote. Battery replacement should
only be performed by authorized Marquis Spas® dealer.
7