Owner`s manual

20
Water Line
To avoid buildup of oils and lotions at the water line, clean the interior when
needed. We suggest the Glove Sponge to clean without scratching.
NOTE: Do not use the same brush or sponge to clean the exterior of the spa
and the interior of the spa. Soap and other product residue used on the outside
of the spa can cause foaming of the spa water and scratches to the spa surface.
Light Bulb Replacement
A. Turn off the power to the spa.
B. Remove the equipment area door to find the light access. (See
EQUIPMENT DIAGRAM.)
C. Remove the lamp socket from the back of the light assembly by turning
counterclockwise and pulling at the same time.
SUSPENDED USE OR WINTERIZING THE SPA
If you decide to discontinue the use of your spa for any extended period of time,
we suggest you follow the steps below.
NOTE: During long periods of inactivity, damage can occur to equipment from
condensation within the equipment compartment.
1. Turn off the power to the spa.
2. Drain the spa. (See DRAINING AND REFILLING THE SPA.)
3. Remove all residual water from the seating and footwell. If necessary, bail
out the remaining water then dry the spa with towels. A wet/dry vacuum is
recommended for best results.
4. Using the wet/dry vacuum, place vacuum nozzle over each jet nozzle to
remove water from plumbing lines, starting with the highest jet and finishing with
the lowest jet.
5. Unscrew the pump plug(s) from the pump(s). (See STARTING YOUR SPA.)
6. Again, using the wet/dry vacuum, place nozzle over the exposed pump
opening(s) to remove excess water. The pump(s) should be removed from
the spa and stored in a climate-controlled room.
7. Clean the spa interior.
8. Clean the filter cartridges.
9. Reinstall the spa cover and lock in place.
NOTE: Direct sunlight on the spa surface can cause severe damage or
blemishing and can result in the voiding of any surface warranties.
IMPORTANT CHEMICAL SAFETY PROCEDURES
1. Always keep chemicals out of reach of children.
2. Read product labels carefully prior to use.
3. When dissolving, always add chemicals to water, do not add water to
chemicals. Some dry chemicals should be dissolved prior to adding them to
the spa. Using a clean container, dip some water from the spa. Mix until
dissolved, then add to circulating water.
4. CAUTION: Do not mix chemicals together. Add them separately to the spa
water.
5. All chemical products should be stored in a cool, dry, well-ventilated area
where the average temperature does not exceed 90°F (32°C). Keep storage
area clean of debris such as rags, newspaper, and combustible materials.
6. Keep chemicals away from open flame or other heat source. Do not smoke
near chemicals. If a dry chlorine chemical fire should occur, use water only.
Do not use a dry chemical fire extinguisher to attempt to put out the fire.
7. When adding chemicals, always keep the water circulating in the spa with
jets in a downward circular pattern for better chemical distribution. Add
chemicals to the spa water one at a time. Allow several minutes between any
new chemical additions using the jet action to evenly distribute throughout
the spa.
8. After adding chemicals, wait the amount of time recommended on the
chemical container before retesting your water for an accurate reading.
Retest your spa water before using.
9. If you have any questions or concerns about the correct procedures for
handling chemicals, please contact your authorized dealer.
WATER CARE
There are three things necessary for clean safe water:
1. CIRCULATE: Water has to be circulated regularly; it can not be stagnant.
2. FILTER: Water has to be filtered to remove particulate and debris.
3. SANITIZE: Water has to be sanitized to kill organisms like algae, bacteria and
virus.
The control system in your spa will automatically circulate and filter. (See SPA
CONTROL OPERATION.) The sanitation requires minimal effort if done
consistently and properly.
To sanitize spa water, three things are required:
1. BALANCE: The water must be balanced so the sanitizer can work and spa
equipment is protected.
2. SHOCK: Shock to oxidize organics and maximize sanitizer efficiency.
3. SANITIZE: Maintain a proper level of sanitizer at all times.
WATER CARE TROUBLESHOOTING
P: Problem
S: Solution
Cloudy Water
P: Inadequate filtration or dirty filter.
S: Ensure that the filter is securely installed. Clean or replace filter.
Increase the length of clean up and/or filter cycles.
P: Water is not balanced.
S: Test water and adjust pH, alkalinity, and sanitizer as needed. Shock to
oxidize and destroy organics in the water.
P: Unfiltered particles or chemically saturated.
S: Use Water Clarifier to combine particles.
P: High total dissolved solids
S: Drain, clean, and refill the spa.
Chemical Odour
P: Too many chloramines/bromamines in the water.
S: Treat water with Spa Shock then adjust sanitizer level as necessary.
P: Dull looking water, difficult to manage. High total dissolved solids
(TDS) may be the cause.
S: Drain and refill with fresh water.
Musty Odour
P: Not enough sanitizer in water – bacteria or algae in water.
S: Add sanitizer as necessary and shock. Readjust sanitizer level if necessary.
Yellow Water
P: Low pH and/or low alkalinity.
S: Test and adjust pH with pH and Alkalinity Up. Adjust alkalinity if necessary.
Foaming
P: High concentration of body oils, lotions or soaps, as well as excessive
organics.
S: Use Spa Defoamer and adjust pH and sanitizer as needed.
Scum Line in Spa
P: Body oils and dirt.
S: Use Glove Sponge to clean the spa. Test and adjust the sanitizer and pH if
necessary. Increase the clean up cycle.
No Sanitizer Reading
P: Sanitizer level is too low.
S: Shock until the sanitizer registers in the recommended range.
P: Test strip remains “white” even after sanitizer has been added.
S: Sanitizer level could be extremely high. It can bleach the reagents on the test
strip and give a false reading. Remove spa cover and activate jets and air
control. Allow jets to run for 30 minutes. Test water to see if desired level has
been reached.
High Sanitizer Reading
P: Too much chlorine or bromine added or dispensed into the spa.
S: Remove spa cover and activate jets and air control. Allow jets to run for 30
minutes. Test water to see if desired level has been reached. Reduce
bromine level.
Eye or Skin Irritation
P: Contaminants or excessive amount of chloramines/bromamines in water.
S: Treat water with Spa Shock. Adjust sanitizer level.