Owner`s manual

7
7. Press the back/set button to save you selection. If you want
to cancel your choice us the temp down button to navigate to
the cancel icon or simply wait 30 seconds which will end the
programming session.
Definitions of menu and sub menu items
Heat mode – Ready or Rest options
 The Ready mode will have the spa at the set temperature at all
times.
 The Rest mode will only heat during a filtration cycle. This is useful
if you are going to be gone for an extended amount of time and
want to conserve on power required to keep the spa hot at all times
Time of day
Setting the time of day will establish the current time in the main display screen
of the panel. It is also important for controlling when filtration cycles will run.
Filter Cycles:
 Filter cycle 1 is set at the factory to run for 1 hour.
 Filter cycle 2 is set at the factory to run for 1 hour.
 Adjusting the time of the filtration cycle/s is a matter of personal
preference and usage patterns. Setting the filtration cycles for late
at night can avoid higher electrical rate costs as an example. If you
live in a climate that is seasonally hot, running the filtration cycle at
night can avoid unwanted heat build-up from the pumps and
prolong the life of the equipment. If your usage patterns are heavy
and you would like additional filtration to occur, you have the choice
of extending the filtration time or changing the second cycle to a
different part of the day.
Preferences

Temp display: Factory set to Fahrenheit “F” but can be changed to
Celsius “C” in alignment with local methods of displaying
temperature

Time display: Factory set to 12 hour but can be changed to 24 hour.
12 hour will display “AM” and “PM” after the time if 12 hour is
chosen. Choosing 24 hour will display the time in military time.

Clean-up: Factory set to 30 minutes (.5hr). A clean-up cycle will
start 30 minutes after you have finished using the hot tub. You
have the ability to extend the clean-up time in .5 hour increments to
suit your usage patterns and increase the filtration of the water after
use.

Language: Factory set to English. Choose between English,
Spanish, French and German to support your specific language in
the display.
Diagnostics

Spa, Information, A/B Temps and Fault Log are sub menu items
used for troubleshooting issues you may encounter with the hot tub
operation. These functions can only be viewed and not changed.
Typically these functions will be used by a service technician but
can be helpful to the owner when reporting an issue to the dealer or
service technician over the phone.
Auxiliary jet buttons: (if equipped)
Depending on the model of hot tub, there are may be up to two auxiliary jet
controls for operating the jet pumps. Pressing the Jets button will turn pump on
low speed. Pressing a second time will turn the pump on high speed. Pressing
the button a third time will turn the pump off. The pump will run for 15 minutes
before shutting off or switching to low speed.
Wi-Fi control: (if equipped)
Your hot tub is configured with a special component that will allow wireless
control with most Apple based products such the iPod Touch, iPad and iPhone.
This is an exciting feature that allows wireless operation of the spa functions and
most settings.
Please note that the typical operating range is within 30 feet of the hot tub
depending on obstructions or location/orientation. The signal may not be strong
enough in some cases to adequately establish and hold communication
between the hot tub and your device especially when operating from indoors
and the signal has to travel through walls. Keep this in mind when placing your
hot tub during installation in an effort to keep any obstructions to a minimum.
Initial set up:
1. In order to communicate and operate the hot tub, you will need to
go to the App Store and download the free “Marquis Spas & Hot
Tubs” app to your device.
2. Go to the settings section on your Apple device and choose the “Wi-
Fi” tab. Be sure that the Wi-Fi selection slider is set to the “On”
position so your device will discover all available Wi-Fi choices.
Choose the tab labeled BWG followed by a series of numbers. Be
sure your device connects which should be shown by the presence
of a check mark next to the name.
3. Return to the main screen and open the Marquis App and proceed
to “connect” with the hot tub. Stopping the connection process and
restarting may be required. There is nothing wrong with the unit as
this can be caused by protocols issued by Apple Inc.
4. Once connected you will be able to operate the jets and light on the
control tab of the App. Moving to the settings tab will allow changing
the time, temperature and filtration settings of the hot tub.
Note: If your device goes to sleep, screen darkens, or is turned off you will need
to reconnect again with the hot tub in order to reestablish control.
Aquavision Monitor (option on Show)
Aquavison is a completely independent waterproof video monitor that is built to
the latest regulations in waterproofing and safety, it is designed to integrate into
your spa environment. Aquavision incorporates the latest state of the art screens
with the latest and best features. Aquavision features heated screen areas to
prevent the front from misting up in humid conditions or even freezing up in cold
conditions. The E-Suite™ features an Aquavision unit with Adagio™ audio
system and a wireless remote control.
Operating the Monitor
Gently push the PRESS pad on top of the self-rising monitor unit to raise it. To
lower the monitor unit gently push the PRESS pad. Make sure monitor unit is in
the down position before closing the spa cover. Monitor lift mechanism is
manufacturer-warranted against failure to lift due to manufacturing defects only.
Closing the spa cover with monitor in the up position or forcing the monitor down
too rapidly can result in damage. Please refer to the Aquavision manufacturer’s
owner’s manual for features, operation, and troubleshooting.
USE AND CARE OF AROMA INFUSIONS LIQUID FRAGRANCE
DISPENSING SYSTEM (SELECT MODELS ONLY)
Filling

Turn the top cap of the Aroma Infusions counterclockwise. Remove
the pump mechanism to expose the reservoir.

The reservoir will hold up to 8oz. of liquid aroma. Monitor the level
during filling to avoid overfilling. Hold the liquid level approximately
1” below the top during filling to ensure the proper operating level.

Once filled, replace the pump mechanism into the reservoir and turn
the cap clockwise. DO NOT over tighten.