OWNER’S MANUAL WELCOME TO THE SPA LIFE! We sincerely hope your spa life is a pleasant experience. If problems should arise, contact your authorized Marquis Spas® dealer. Or contact Marquis Corp. at any of the following: Email: service@marquiscorp.com Web: www.marquisspas.com Marquis Corp. 596 Hoffman Road Independence, OR 97351, USA This manual is provided to enhance your enjoyment of your spa and to prevent non-warranty situations.
OO WW N ENRE’ SR ’MSA NM UA ALN IU ND AE LX IMPORTANT SAFETY INSTRUCTIONS 120V, Cord Connected Models .................................................................. 3 240V, Permanently Installed or Converted Models ............................. 4 All Spa Models ..................................................................................................4-5 Personal Safety ................................................................................................
SAFETY INSTRUCTIONS The following instructions are required to be printed by Underwriters Laboratories (UL) as a condition of the listing of this product. They contain important safety information. We strongly encourage you to read and apply them. IMPORTANT SAFETY INSTRUCTIONS WHEN INSTALLING AND USING THIS ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING: 1. READ AND FOLLOW ALL INSTRUCTIONS 2.
SAFETY INSTRUCTIONS 240 VOLT, PERMANENTLY INSTALLED OR CONVERTED MODELS 9. A ground terminal is provided on the terminal block (TB-1, terminal 7) located inside the control box. To reduce the risk of electric shock, connect this terminal to the grounding terminal of your electrical service or supply panel with a continuous green, insulated copper wire. The wire must be equivalent in size to the circuit conductors supplying the equipment.
SAFETY INSTRUCTIONS • Persons using medications should consult a physician before using a spa since some medication may induce drowsiness while other medication may affect heart rate, blood pressure, and circulation. 15.DANGER: TO REDUCE THE RISK OF INJURY TO PERSONS. Do not remove the suction fittings. 16.DANGER: RISK OF INJURY: Never operate a spa if the suction guard(s) is broken or missing. Never replace a suction guard with one rated less than the flow rate marked on the original suction guard.
SAFETY INSTRUCTIONS SAFETY INSTRUCTIONS FOR FRENCH SPEAKING SPA OWNERS AVERTISSEMENT: Ne pas placer d’appareil électrique (luminaire, téléphone,radio, téléviseur, etc.) moins de 1.52 m de cette cuve de relaxation. AVERTISSEMENT: Ne pas laisser les enfants utiliser une cuve de relaxation sans surveillance. AVERTISSEMENT: Pour éviter que les cheveux ou une partie du corps puissent être aspirés, ne pas utiliser une cuve de relaxation si les grilles de prise d’aspiration ne sont pas toutes en place.
SAFETY INSTRUCTIONS Other booklets about spa safety are: “Children Aren’t Waterproof,” “Pool and Spa Emergency Procedures For Infants and Children,” “Layers of Protection” and “The Sensible Way to Enjoy Your Spa” published by APSP. WARNING: The use of alcohol, drugs, or medication can greatly increase the risk of fatal hyperthermia in hot tubs and spas. Persons taking medications which induce drowsiness such as tranquilizers, antihistamines, or anticoagulants should not use the spa.
INSTALLATION INSTRUCTIONS LOCATION For your portable spa to function properly and safely, it must be located on a hard, flat, level surface. Inground spas require special installation techniques and should be planned in conjunction with your authorized Marquis Spas® dealer. Improper installation can result in structural damage to the spa and the voiding of your spa warranty.
O U T DINSTALLATION O O R & P A T IINSTRUCTIONS O INSTALLATION OUTDOOR AND PATIO INSTALLATION To install the spa outdoors, we recommend a reinforced concrete pad at least four inches thick. The reinforcing material should be attached to a #8 AWG bonding wire per national and local electrical code. If you place the spa on the ground, even temporarily, place the spa empty of water on concrete pavers under the entire bottom of the spa.
INSTALLATION Shut-off valve in open position INSTRUCTIONS SHUT-OFF VALVES Your spa is equipped with shut-off valves (see EQUIPMENT DIAGRAM) that shut off the water flow to the equipment system for authorized Marquis Spas® dealer service. At times, a new spa or one that has recently been serviced, may have the shut-off valves partially closed which can restrict the water flow and hinder jet performance. Be sure the valves are fully open.
INSTALLATION Safety guard of suction fitting must remain in place. INSTRUCTIONS SUCTION GUARDS The suction guard(s) in the footwell of your spa is an opening through which the jet pump(s) draws water. Suction fittings are equipped with a safety guard. Suction through the fittings can be strong. The safety guard(s) must remain in place and undamaged. A fitting with a damaged guard(s) can be dangerous, especially to small children or people with long hair.
INSTALLATION INSTRUCTIONS • For units used in other than single-family dwellings, a clearly labeled emer gency switch shall be provided as part of the installation. The switch shall be readily accessible to the occupants and shall be installed at least five feet (1.52 m) away, adjacent to, and within sight of the unit.
INSTALLATION INSTRUCTIONS 1. Press TEMP+, then JETS 1, then SPA LIGHT. 2. Press TEMP+ repeatedly until “gFC” is displayed, then press JETS 1. 3. Press TEMP+ until “gC.n” is displayed, then press JETS 1 to clear the GFCI Status; you will see gS.A” displayed verifying that the GFCI Status has been set to “Armed”. The system will exit this menu in 30 seconds if no buttons are pressed. *When you enter the GFCI menu, it always shows you the current status first. “gS.
STARTING YOUR SPA START-UP PROCEDURE Your spa is equipped with solid-state Comfort Controls specific to your spa model. (See SPA CONTROL OPERATION for your specific spa model.) To start your spa, you need spa test strips. It is important to follow each of these steps when starting your spa. Once you have completed the following steps, see MARQUIS CARE AND ENJOYMENT GUIDE for proper water treatment. NOTE: Your spa has been filled and test-run at the factory.
STARTING Fill spa with water to two-thirds of the way up the Vortex skimmer opening. Vent air by slightly opening pump unions. Use TEMP pad to set water temperature. YOUR SPA 4. Install filter cartridges. (See INSTALLATION INSTRUCTIONS, Filter Cartridges.) 5. Fill the spa with water to two-thirds of the way up the Vortex skimmer openings. The use of a Fill Filter is recommended, especially in areas with high mineral content in the water. 6. Turn the power on. 7.
STARTING YOUR SPA Marquis suggests you use the safety locks to help keep out unintended users and prevent covers from being blown off in windy conditions. The cover and retractable cover system are not recommended for use in wind conditions reaching above 25 miles per hour. If your spa is located in an area susceptible to high winds, additional cover lock straps may be necessary to minimize cover damage. Open the spa cover: 1. Unfasten all cover lock straps. 2.
THE D E S T I N Y TM # Component Identification Qty.
D E SINSTALLATION T I N Y TM T H E R INSTRUCTIONS APY CONTROL ZONE 1 (pump 2) Upper-body jets.* ZONE 4 (pump 1) Upper- and mid-body jets.* ZONE 2 (pump 2) Upper-, mid-, and lowerbody jets.* ZONE 5 (pump 1) Upper-, mid-, and lowerbody jets.* ZONE 3 (pump 2) Lower-body jets.* ZONE 6 (pump 1) Lower-body jets.* *HK8 neck jets operate in every zone.
THE E N V Y TM # Component Identification Qty. 1 2 4 5 7 8 9 11 12 13 14 15 19 HKTM8 Jets HK™12 Jets HK™40 Jets Light (option) Suction Fittings Floor Drain Jet Selector Bather’s Control Panel Filter Canister Spa Frog® (option) Spa Frog® Return Fitting (option) Ozone-ready Injector Fitting ConstellationsTM (option) 3 8 3 1 2 1 1 1 1 1 1 1 12 Physical Specifications Size Dimensions Height Seating Capacity/Positions Weight Dry/Lbs. Weight Full/Lbs.
THE E P I C TM # Component Identification Qty.
E P I C TM T H E R A P Y CONTROL A (PUMP 2) Tri-Zone A in position 1: Therapy Pillar* B (PUMP 1) Tri-Zone B in position 3: Full-back* A (PUMP 2) Tri-Zone A in position 2: Overall-back* B (PUMP 1) Tri-Zone B in position 2: Overall-back* A+C (PUMP 2) Tri-Zone A in position 3 and Tri-Zone C in position 1: Feet* B+D (PUMP 1) Tri-Zone B in position 1 and Tri-Zone D in position 3: Thighs* *HK8 neck jets operate in every zone 21
THE E U P H O R I A TM # Component Identification Qty.
E U P H O R I A TM T H E R A P Y CONTROL ZONE 1 ZONE 2A Upper-, mid- and lower-body jets.* ZONE 2B Lowerback jets.* *Neck jets operate in all zones.
THE M I R A G E TM # Component Identification Qty.
MIRAGE™ THERAPY CONTROL ZONE 1A Upper- and mid- and lower-back jets.* ZONE 1B Lowerbody jets.* *Neck jets operate in all zones.
THE P R O M I S E TM # Component Identification Qty.
P R O M I S E TM T H E R A P Y CONTROL ZONE 2 Upper-, mid- and lower-back jets.* ZONE 1 Lowerbody jets.* *Neck jets operate in zone 2. Waterfall operates in zone 1.
THE Q U E S T TM # Component Identification Qty.
Q U E S T TM T H E R A P Y CONTROL ZONE 1 Upper- and mid- and lower-body jets.* ZONE 2 Upper- and mid-body jets.* ZONE 3 Lowerbody jets.* *HK8 jets operate in every zone.
THE R E N D E Z V O U S TM # Component Identification Qty.
THE R E S O R T TM # Component Identification Qty.
R E S O R T TM T H E R A P Y CONTROL ZONE 2A Upper-, mid- and lower-back jets.* 1 2 ZONE 2B Lowerbody jets.* 1 2 *Neck jets operate in zone 2.
THE R E T R E A T TM # Component Identification Qty.
THE R E W A R D TM # Component Identification Qty.
R E W A R D TM T H E R A P Y CONTROL ZONE 1 ZONE 2A Upper- and mid- back, and leg jets.* ZONE 2B Lowerbody jets.* *Neck jets operate in all zones.
THE S P I R I T TM # Component Identification Qty.
S P I R I T TM T H E R A P Y CONTROL ZONE 1A Upper- and mid- and lower-back jets.* ZONE 1B Lowerbody jets.* *Neck jets operate in all zones.
SPA CONTROL OPERATION ALL SPA MODELS PUMP PRIMING (Pr) Pump priming feature begins at start-up. When your spa is energized, the LCD window displays a “Pr” message. This mode lasts approximately four to five minutes, if not exited manually by pressing the TEMP+- pad. If pump is on but no water is coming out of the jets the system might be air locked. Use the following steps to resolve the lock. 1. Open equipment compartment. 2. Find the thumb screw on the elbow between the pump and the heater. 3.
SPA CONTROL OPERATION JETS Use the JETS pad on the bather panel or remote control. First press of the JETS pad activates pump on low-speed (and starts soak timer). Second press of the JETS pad activates pump on high-speed. Third press of the JETS pad turns jets off for all-quiet mode. Fourth press of the JETS pad turns pump back to low-speed. If the pump is already on low (heating, filter cycle) then the first press starts the soak timer.
SPA CONTROL OPERATION achieve the most effective cleansing. Selectable choices for the settings of the operation systems allows flexibility and ensures your Marquis spa remains easy to maintain for your particular set of circumstances. SOLID-STATE OZONATOR (OPTION) The ozone generator functions whenever the system is running on filter or clean up cycles. CAUTION: Do not block ozone injector fitting (see spa diagrams).
SPA CONTROL OPERATION Selectable SmartClean™ Settings • 1H: 1 hour • 2H: 2 hours • 3H: 3 hours • 4H: 4 hours • OH: Off To adjust the SmartClean™ settings: Use the TEMP+- pad to scroll through options. When desired selection has been reached. Press SETTING pad to enter selection and exit settings mode. TEMPERATURE DISPLAY AND ADJUSTMENT Factory Default Settings: • Temperature: 102°F (39°C) The LCD window displays the actual water temperature.
SPA CONTROL OPERATION Sleep Mode (SL) Your spa will maintain a water temperature that is 20°F (7°C) below the set temperature. The heater functions only during a filter cycle. The LCD window displays “SL” flashing alternately with the actual temperature when the spa is up to set temperature and displays “SL” steadily when below set temperature. To Adjust the Heat Mode: First press the SETTING pad to display the heat mode settings (St, Ec, SL). Use the TEMP+- pad to scroll through the options.
SPA CONTROL OPERATION DESTINY & EPIC MARQUIS SIGNATURE COLLECTIONS Pr PUMP PRIMING (Pr) Pump priming feature begins at start-up. When your spa is energized, the LCD window displays a “Pr” message. This mode lasts approximately four to five minutes, if not exited manually by pressing the TEMP+ pad. UNDERWATER AND ENTRYWAY LIGHTS Press the LIGHTS pad on the bather’s panel or remote control (option) to turn the underwater and Entryway lights on and off.
SPA CONTROL OPERATION SETTINGS Clock Press the CLOCK pad followed by the SETTING pad. “Program” will be shown in the upper left corner of the panel display and the hour will begin flashing. To adjust, press the TEMP+ or TEMP- pad. Once the correct hour has been set, press SETTING pad to set the minutes. “Minutes” will flash. Follow above procedure to set the correct minutes. Filter Cycle 1: Press the CLOCK pad followed by the SETTING pad three times to enter Filter 1 programming.
SPA CONTROL OPERATION HEAT MODE Your spa comes preset in the standard heat mode. Allow about one hour per one degree F for heating your spa water when increasing the temperature to the desired level. The heat mode can be adjusted to one of three different settings: Standard Mode The spa water heats as necessary to maintain the set temperature. “Standard” will display until the mode is changed.
SPA CONTROL OPERATION CONSTANTCLEAN™ WATER MANAGEMENT WITH BUILT-IN SANITATION SYSTEM (See Built-in Sanitation System) Ozonator Operation (optional) The ozone generator functions whenever pump 1 is on low-speed in Filter cycles and SmartClean™ cycles ONLY. User Preference Settings Suppress reminders: Displayed as (Sr.n) for no, and (Sr.Y) for yes. When set to (Sr.Y), reminders are never shown in the display. When set to (Sr.n), all reminders are shown. Temperature display in Fahrenheit: Displayed as (tc.
SPA CONTROL OPERATION Quiet Soak Press the QUIET SOAK pad to enter the soak mode. All automatic functions related to the pumps are disabled (i.e., filter cycles, SmartClean™ cycles). If either pump 1 or pump 2 are operating, they will be turned off. Soak mode lasts for 30 minutes, then the spa returns to normal operation. All button functions operate as normal while in a Soak mode. When in a Soak mode, the Soak LED will illuminate. Marquis Ozonator reduces the need for chemical sanitizers.
SPA CONTROL OPERATION Spa Monitor In-house Remote Epic and Destiny See Spa Monitor manual for complete set up and operation instructions. Dolphin Remote Control Spa Functions Use the Waterfall, lights, jets, soak, clock, and timer pads to control spa functions. Dolphin Remote Soundsations™ operation It is designed with sophisticated technology that will allow you to consolidate many of your existing remote controls along with the Soundsations audio-ready system in your spa.
SPA CONTROL OPERATION SOUNDSATIONS™ AUDIO-READY SYSTEM Spa location and speaker cord routing The factory-installed speaker cord located inside the spa’s equipment compartment is 100 ft. long. You must locate the spa close enough to the audio source to allow the cord to be run so it is not exposed to damage and does not create a trip hazard. NOTE: A 200 ft. long speaker cord is available as an optional replacement for the supplied 100 ft. cord. Ask your authorized Marquis Spas® dealer for details.
SPA CONTROL OPERATION WARNING! Never use broken or frayed wire, as damage or electrical shock may result. + RED R CAUTION! Exposing too much wire or having wires with frayed ends could cause wires to touch each other, which could damage the equipment. BLACK - WHITE L + Wire connections. GREEN 3. Wire connections A. Red = Right (+) B. Black = Right (-) C. White = Left (-) D. Green = Left (+) NOTE: Do not connect speaker cord to any speaker terminals already in use. 4.
ADAGIO™ AUDIO SYSTEM ADAGIO™ AUDIO SYSTEM Adagio™ Stereo Adagio is easy to operate with logical push button controls and function keys. Please refer to the Poly-Planar Marine Audio Center Manufacturer’s owner’s manual for features, operation, and troubleshooting. NOTE: Avoid water splashing on the stereo face. Never insert a disk or operate the stereo with wet hands. Moisture can damage internal components. Water intrusion into stereo is not covered under warranty.
EQUIPMENT DIAGRAM ENVY, MIRAGE, PROMISE, QUEST, RENDEZVOUS, RETREAT AND SPIRIT # Component Quantity 1 2 3 4 5 6 7 8 9 10 11 12 13 Control box and heater Pump Slice valves GFCI Pump unions Pump plug Motor mounts Light Check valve (option) Ozonator fitting Ozonator (option) Drain valve 1 1 2 1 2 1 4 1 1 1 1 1 1 Soundsations™ plug (option) 52
EQUIPMENT DIAGRAM DESTINY AND EPIC EUPHORIA, RESORT AND REWARD # Component Quantity 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Control box and heater Ozonator (option) Pumps Check valve (option) Slice valves Pump unions Drain valve Adagio™ Stereo Head (option) Cross Over Control (option) Spa Control (option) MP3 Auxiliary Jack (option) Stereo Power Supply (option) Spa Monitor (option) Ozonator fitting Light (option) 1 1 2 1 2 4 1 1 1 1 1 1 1 1 1 53
TROUBLESHOOTING GUIDE PLEASE NOTE: The following corrective actions may be performed by the spa owner. If the trouble cannot be corrected in the steps below, please contact your authorized Marquis Spas® dealer for service. (Improper servicing by an unauthorized service provider or spa owner could result in damage not covered by the warranty and could cause serious injury.) EQUIPMENT WILL NOT OPERATE • Check the control panel LCD window for diagnostic code.
TROUBLESHOOTING LCD DIAGNOSTIC MESSAGES The advanced technology built into the spa allows it to perform a number of self-diagnostic system checks and it can display a variety of messages in the LCD window on the control panel. OHH: Over heat protection. If a malfunction occurs and the spa water reaches 112°F (44°C), the system completely shuts down. In such a condition, DO NOT ENTER THE WATER. Turn off all power to the spa. Remove spa cover and allow water to cool.
TROUBLESHOOTING LF: Persistent low flow problems. (Displays on the fifth occurrence of the HFL message within 24 hours.) Heater is shut down, but other spa functions continue to run normally. Follow active required for HFL message. Heating capacity of the spa will not reset automatically. You may press any pad to reset. dr: Inadequate water detected in heater. Check water level in spa. Refill if necessary. If the water level is okay, make sure the pumps have been primed.
TROUBLESHOOTING MAINTENANCE REMINDERS The following reminders will be shown on the LED lights indicating it is time for maintenance. Reminder messages will also be displayed in the LCD window. Reset the reminders by pressing the TEMP+, TEMP- , or SETTINGS pad. Check Bromine: rSA will be displayed in the LCD window every 21 days. Clean Filter: LED will illuminate every 30 days. rCL will be displayed in the LCD window. Change Water: LED will illuminate every 90 days. rCH will be displayed in the LCD window.
MARQUIS CARE & ENJOYMENT GUIDE IMPORTANT CHEMICAL SAFETY PROCEDURES 1. Always keep chemicals out of reach of children. 2. Read product labels carefully prior to use. 3. When dissolving, always add chemicals to water, do not add water to chemicals. Some dry chemicals should be dissolved prior to adding them to the spa. Using a clean container, dip some water from the spa. Mix until dissolved, then add to circulating water. 4. CAUTION: Do not mix chemicals together. Add them separately to the spa water. 5.
MARQUIS CARE & ENJOYMENT GUIDE The control system in your Marquis spa will automatically circulate and filter. (See SPA CONTROL OPERATION, ConstantClean™ and SmartClean™ sections.) The sanitation requires minimal effort if done consistently and properly. To sanitize spa water, three things are required: 1. BALANCE: The water must be balanced so the sanitizer can work and spa equipment is protected. 2. SHOCK: Shock to oxidize organics and maximize sanitizer efficiency. 3.
MARQUIS CARE & ENJOYMENT GUIDE Calcium Hardness Do not use soft water in your spa. It is critical to have calcium in your water. The ideal range of calcium is between 200 – 300 ppm. The calcium hardness is normally adjusted when filling or refilling after draining the spa. High calcium levels can cause scale buildup on spa surfaces and equipment. Your spa can be protected against high calcium by using Metal & Stain Remover per the directions on the container.
MARQUIS CARE & ENJOYMENT GUIDE SANITIZE ConstantClean™ System (option) The ConstantClean™ system utilizes a combination of sanitizers to increase water quality and significantly decrease maintenance. The combination of a Spa Frog® Mineral Cartridge* and the factory installed ozonator greatly reduce the amount of sanitizer required. Instead of the normal 3 - 5 ppm of bromine, you may only need to maintain 1 - 2 ppm of bromine. NOTE: The use of Spa Frog® floating cartridges is recommended.
MARQUIS CARE & ENJOYMENT GUIDE INSTALL THE CARTRIDGES Locate and remove the cartridge holder cap on the top lip of the spa. Push down and turn the holder counterclockwise to unlock. Lift holder out. Snap the Spa Frog® mineral cartridge into the area of the holder marked “MINERALS” (top portion), making sure to line up the indentation near the top of the cartridge with the raised line on the holder. Then snap the Spa Frog® bromine cartridge into the area of the holder marked “BROMINE”.
MARQUIS CARE & ENJOYMENT GUIDE AS NEEDED PRODUCTS pH & Alkalinity Increase pH & Alkalinity Decrease These two products work to raise or lower the pH and alkalinity in the spa. They are only needed if the test strip indicates the levels are not in the ideal ranges. Water Clarifier Microscopic particles can pass through the spa filter and create cloudy water.
MARQUIS CARE & ENJOYMENT GUIDE WATER CARE TROUBLESHOOTING GUIDE NOTE: If you request a service call and no problem is found with the spa or the problem is not covered by warranty (i.e. chemical damage), you will be charged at the regular service rate. P: Problem S: Solution Cloudy Water P: Inadequate filtration or dirty filter. S: Ensure that the filter is securely installed. Clean or replace filter. Increase the length of clean up and/or filter cycles. P: Water is not balanced.
MARQUIS CARE & ENJOYMENT GUIDE No Sanitizer Reading P: Sanitizer level is too low. S: Shock and/or adjust Spa Frog® bromine cartridge until the sanitizer registers in the recommended range. P: Test strip remains “white” even after sanitizer has been added. S: Sanitizer level could be extremely high. It can bleach the reagents on the test strip and give a false reading. Remove spa cover and activate jets and air control. Allow jets to run for 30 minutes. Test water to see if desired level has been reached.
MAINTENANCE WEEKLY MAINTENANCE Removing Debris Remove any debris and leaves from the Vortex skimmers and suction guard(s) on the inside of the spa. Blocked intakes can impede the flow of water through the jetting system. Water Level Replenish the water level if necessary so that it is approximately two-thirds up the Vortex skimmer opening. (See STARTING YOUR SPA.) Low and high water levels can damage your spa. It is important to check your water level often.
MAINTENANCE Leakage Detection Open the equipment door and check for signs of water leakage around the pump(s). Pump seals wear out over time, especially with improper water chemistry. Early detection of pump seal failure can significantly reduce repair costs. Pump seals, heater gaskets and pump gaskets must be checked each month to ensure they are not leaking. Further damage caused by a leak from any component is not covered under the warranty.
MAINTENANCE 7. Place the end of the tubing into the vinegar, making certain that the end of the tubing sits at the bottom of the container. 8. Reconnect power to the spa. 9. Run the spa until all of the vinegar is gone. This should allow an ample low of vinegar to be run through the injector and clear the blockage. 10. Disconnect power to the spa. 11. Remove the empty cup or bucket. 12. Reinstall the tubing to the bottom of the ozonator. 13. Plug the ozonator into the control box. 14.
MAINTENANCE Refill the Spa Fill the spa with fresh water from a garden hose and balance the water as described in the Water Treatment section. The use of a Fill Filter is recommended when filling especially in areas of high mineral content in the water. Attach to the end of a garden hose to filter out any grit and sediment that could accumulate in the spa and potentially scratch the spa surface.
MAINTENANCE Light Bulb Replacement: 1. Turn off the power to the spa. 2. Remove the equipment area door to find the light access. (See EQUIPMENT DIAGRAM.) 3. Remove the lamp socket from the back of the light assembly by turning counterclockwise and pulling at the same time. 4. Gently pull the bulb out of the lamp socket and replace it with a 6 watt bulb only (GE #918) available from your spa dealer. 5. Install the lamp socket back into the light assembly and replace door.
S PA C A R E ™ PRODUCTS spa boutique TM SpaBoutique™ A collection of unique items to delight your senses, free your time, and make your life easier. SpaCare™ gives you maintenance products to ease spa care – inside, outside, and especially the water. SpaTherapy™ surrounds your senses with aromas, visions, sounds and feel-good products to bring you and your environment to life. SpaStyle™ brings convenience items to enhance your lifestyle, while soaking in the spa or relaxing on the deck.
OWNER’S PROTECTION PLAN MARQUIS SPAS® LIMITED WARRANTY What the Marquis Corp. Limited Warranty Covers Marquis Corp. warrants that our products will be free from defects in materials and workmanship for the term set forth exclusively in this warranty. Accessories purchased from Marquis Corp. or a Marquis Corp. authorized Marquis Spas® dealer and added to the spa after manufacture of the spa are not covered under this warranty but may have other warranties.
OWNER’S PROTECTION PLAN Term of the Marquis Corp. Limited Warranty The term of your warranty begins on the date the product is sold to you and continues for the term described in this warranty for each component. What You Should Do if You Experience a Problem Unless otherwise designated in writing by Marquis Corp., Marquis Corp. or its agent are the only parties authorized to perform warranty service on Marquis Corp. spas. Upon experiencing a problem, please contact your authorized Marquis Spas® dealer.
OWNER’S PROTECTION PLAN Other items not included in this warranty are freight expenses; labor and material cost associated with removal and or replacement of the spa; damage to or fading of the spa surface and staining of the spa surface or equipment caused by impact, scratching, abrasive or corrosive cleaners; damage due to extreme water temperatures outside the range of 32°F to 120°F (0°C to 49°C) even if the damage was the result of a covered failure; or damage to the spa surface or equipment caused b
