Owner’s Manual L E I S U R E S P O R T S E R I E S S E R I E S C O A S T A L U L T I M A T E S E R I E S S E R I E S
OWNER’S MANUAL WELCOME TO THE SPA LIFE! Please enjoy your new Marquis spa, but think Safety First. Read your Owners Manual in its entirety before installing your spa and encourage all spa users to do the same. More than just common sense, this Owners Manual provides vital safety and operational information. Every effort has been made to ensure the accuracy of this manual. However, Marquis Spas reserves the right to improve its product without notice.
OWNER’S MANUAL INDEX IMPORTANT SAFETY INSTRUCTIONS 120V, 240V, All Spa Models, Personal Safety..................................................................................3-6 SPA INSTALLATION Location.................................................................................................................................................................7-8 Ozonator Installation.........................................................................................................................
SAFETY INSTRUCTIONS (CONTINUED) The following instructions are required to be printed by Underwriters Laboratories (UL) as a condition of the listing of this product. They contain important safety information, and we strongly encourage you to read and apply them. IMPORTANT SAFETY INSTRUCTIONS WHEN INSTALLING AND USING THIS ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING: 1. READ AND FOLLOW ALL INSTRUCTIONS 2.
SAFETY INSTRUCTIONS (CONTINUED) 10. Your spa uses ground fault circuit interrupters in the electrical sub-panel. Before each use of the spa and with the unit operating press the Test button on each breaker. The switch should click over to the Trip position. Wait thirty seconds and reset each GFCI breaker by switching it completely off and then completely on. The switch should then stay on.
SAFETY INSTRUCTIONS WARNING:Children should not use spas or hot tubs without adult supervision. WARNING:Do not use spas or hot tubs unless all suction guards are installed to prevent body and hair entrapment. WARNING:Do not use drugs or alcohol before or during the use of a spa or hot tub to avoid unconsciousness and possible drowning. WARNING:People using medications and/or having an adverse medical history should consult a physician before using a spa.
GENERAL INFORMATION SAFETY SIGN Each Marquis Spa is shipped with a SAFETY SIGN in the spas Owners Package. Underwriters Laboratories (UL) recommends this sign be permanently installed where it is visible to the users of the spa. To obtain additional Safety Signs, contact your Marquis Spas dealer and request Part #710-0789. Replacement Owners Manuals are also available.
INSTALLATION INSTRUCTIONS LOCATION For your portable spa to function properly and safely, it must be located on a hard, flat, level surface. In-ground spas require special installation techniques and should be planned in conjunction with your spa dealer. Improper installation can result in structural damage to the spa and the voiding of your spa warranty.
INSTALLATION INSTRUCTIONS (CONTINUED) OVERHEATING In the case of extended hot weather, the spa water temperature may reach and maintain 104° F to 106° F. This is due to the ambient temperature and the full insulation in the spa cabinet. The simplest solution to this heat buildup is, lifting the spa cover a few inches for several hours to allow the heat to escape. You may also have the option of shortening the pump-run time. See Control panel section for available options.
INSTALLATION INSTRUCTIONS (CONTINUED) 7. Remove the black cap from the barbed fitting suspended above the equipment (some water may drip from this fitting, have a towel handy). 8. Place the exposed tubing end on the 1/4" barb. 9. There is a labeled mounting block attached to the spa which shows the mounting position of ozonator. CAUTION: DO NOT PREDRILL SCREW HOLES. 10. Turn on the power to the spa.
INSTALLATION INSTRUCTIONS (CONTINUED) 120 Volt: 120V units must only be connected to a properly grounded, grounding type15 amp receptacle. 120V equipment is designed to operate on 60Hz Alternating current only at a voltage of 120, 12.5 amp. maximum load. To Convert 120V to 240V All connections must be made by a licensed electrician. 1. Disconnect from power and remove cord. 2. Move red wire (TB-1) to (TB-4) as indicated by gray area. 3.
STARTING YOUR SPA START-UP PROCEDURE 4. Fill the spa with water to two-thirds of the way up the J Vortex skimmer opening(s). The use of a Fill Filter, #5039, is recommended, especially in areas with high mineral content in the water. 5. Turn the power on and wait five seconds. 6. At this time the spa should have water flowing from the jets.
OPERATING YOUR SPA THERAPY PUMP(S) Allow the spa to circulate on high-speed (see instructions for spa side controls) for 4-5 minutes to discharge air from the plumbing system. Do not expect hot water immediately from the jets; the heater will take several hours to heat the water. Pr Diagnostic Message NOTE: Coastal and Ultimate Series spas have a pump priming feature which begins at start-up. When the spa is energized, the LCD panel will display a Pr message.
OPERATING YOUR SPA MAXIMUM THERAPY JETTING SYSTEM JET SELECTOR VALVE The large, gray teardrop Jet Selector lever allows you to redirect the water flow to different jet zones. (See ZONED JETTING for specific options.) Jet Selector Valve Iso Boost Jet CASCADE NECK JETS Your spa may be equipped with a Therapy Seat(s) featuring especially high Cascade Neck Jets. These jets are turned on and off (when the jet pump is on) using the small teardrop Neck Jet Control lever.
M A R Q U I S S P A S 3 2-speed 56 frame Y O U R ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 425 gallons ○ 3 2-speed 56 frame ○ ○ ○ 425 gallons ○ 2 2-speed 56 frame ○ ○ 420 gallons ○ ○ ○ ○ ○ ○ ○ ○ ○ 320 gallons ○ ○ 300 gallons ○ ○ ○ ○ ○ ○ 425 gallons ○ ○ 425 gallons ○ ○ ○ ○ ○ ○ ○ 300 gallons ○ ○ 300 gallons 380 gallons W O R L D ○ ○ ○ ○ ○ ○ ○ 320 gallons ○ ○ 320 gallons ○ ○ ○ ○ ○ ○ ○ 210 ga
OASIS Leisure serieS Physical Specifications Dimensions Height Depth Seating Positions Weight Dry Lbs. Weight Full Lbs.
SPIRIT Leisure series Physical Specifications Dimensions Height Depth Seating Positions Weight Dry Lbs. Weight Full Lbs.
SPIRIT LX Physical Specifications Dimensions Height Depth Seating Positions Weight Dry Lbs. Weight Full Lbs.
MIRAGE LEISURE SERIES Physical Specifications Dimensions Height Depth Seating Positions Weight Dry Lbs. Weight Full Lbs.
MIRAGE LX Physical Specifications Dimensions Height Depth Seating Positions Weight Dry Lbs. Weight Full Lbs.
LEISURE SERIES CONTROLS Soak Timer: 1st press turns pump to low-speed and starts 59minute timer; 2nd press “all quiet” mode LEISURE SERIES 100°F SOAK TIMER TEMP SET CL: Clean Filter CH: Change Water M AINTENANCE R EMINDERS Temp Set: Actual temperature displayed on LCD; Press repeatedly to increase temperature; Pause; Repeat to decrease temperature Heat On: Illuminates when heat is on HEAT ON LIGHT ON/OFF ZONE 1 JETS CONSTANT C LEAN F ILTRATION LCD Display: Shows temperature, Maintenance Reminders
LEISURE SERIES CONTROLS PROGRAMMABLE FILTER TIMES F1: 45 minutes F2: 2 hours F4: 4 hours F6: 6 hours To adjust the filter time: First press the TEMP SET pad, then press the ZONE 1 JETS. The LCD display will show either F1 (45 minutes), F2 (two hours), F4 (four hours), or F6 (six hours). Press the TEMP SET pad to scroll through the selections and then press the ZONE 1 JETS pad to enter.
LEISURE SERIES CONTROLS ZONED THERAPY SYSTEM AUXILIARY PANELS Pressing the ZONE 1 JETS pad will activate the Power Therapy Seat (see ZONED JETTING for exact location). The ZONE 1 JETS pad will cycle the jet pump from lowspeed to high-speed to off. ED THE R APY SY STE M Z ON ZONE 1 JETS Pump Timeouts Zone 1: Operating sequence is low speed, high speed, then off. If left running, the low speed will turn off after 15 minutes.
spirit ZONED JETTING D E 2 2 A 5 6 A B J 5 6 2 2 ZONE 1A JETS Therapy Seat jets (J) except center jet (A). To activate jets: Turn the Jet Selector Valve (6) to the east. Press ZONE 1 JETS pad (2) to turn pump on low-speed. Press ZONE 1 JETS pad (2) again to turn pump on high-speed. Adjust the jet pressure with the Air Control Valve (5). Open the Air Control Valve by turning the lever counterclockwise. ZONE 1B JETS All jets in seats (B, D, E) plus jet (A).
MIRAGE ZONED JETTING 2 5 F F 2 5 H H W 6 6 H H W F F 2 2 ZONE 1A JETS All the upper level jets (F) and Wrist Jets (W). Turn the Jet Selector Valve (6) to the south. Press ZONE 1 JETS pad (2) on either panel to turn pump on low-speed. Press either ZONE 1 JETS pad (2) again to turn pump on high-speed. Adjust the jet pressure with the Air Control Valve (5). Open the Air Control Valve by turning the lever counterclockwise. MIRAGE lx 5 ZONE 1B JETS All the lower level jets (H).
500 SPORT SERIES Physical Specifications Dimensions Height Depth Seating Positions Weight Dry Lbs. Weight Full Lbs. Water Capacity Total Therapy Jets M A R Q U I S S P A S 84" x 84" 35.
500 LX SPORT SERIES Physical Specifications Dimensions Height Depth Seating Positions Weight Dry Lbs. Weight Full Lbs. Water Capacity Total Therapy Jets M A R Q U I S S P A S 84" x 84" 35.
600 SPORT SERIES Physical Specifications Dimensions Height Depth Seating Positions Weight Dry Lbs. Weight Full Lbs. Water Capacity Total Therapy Jets M A R Q U I S S P A S 84" x 84" 35.
600 LX SPORT SERIES Physical Specifications Dimensions Height Depth Seating Positions Weight Dry Lbs. Weight Full Lbs. Water Capacity Total Therapy Jets M A R Q U I S S P A S 84" x 84" 35.
700 SPORT SERIES Physical Specifications Dimensions Height Depth Seating Positions Weight Dry Lbs. Weight Full Lbs. Water Capacity Total Therapy Jets M A R Q U I S S P A S 90" x 90" 35.
700 LX SPORT SERIES Physical Specifications Dimensions Height Depth Seating Positions Weight Dry Lbs. Weight Full Lbs. Water Capacity Total Therapy Jets M A R Q U I S S P A S 90" x 90" 35.
sport sERIES CONTROLS Soak Timer: 1st press turns pump to low-speed and star ts 59-minute timer; 2nd press “all quiet” mode sPORT sERIES 100°F SOAK TIMER TEMP SET CL: Clean Filter CH: Change Water ! HEAT ON LIGHT ON/OFF JETS LOW/HIGH CONSTANT CLEAN FILTRATION MAINTENANCE REMINDERS Temp Set: Actual temperature displayed on LCD; Press repeatedly to increase temperature; Pause; Repeat to decrease temperature Heat On: Illuminates when heat is on LCD Display: Shows temperature, Maintenance Reminders
sport sERIEs CONTROLS PROGRAMMABLE FILTER TIMES F1: 45 minutes F2: 2 hours F4: 4 hours F6: 6 hours To adjust the filter time: First press the TEMP SET pad, then press the ZONE 1 JETS. The LCD display will show either F1 (45 minutes), F2 (two hours), F4 (four hours), or F6 (six hours). Press the TEMP SET pad to scroll through the selections and then press the ZONE 1 JETS pad to enter.
sport SERIES CONTROLS ZONED THERAPY SYSTEM AUXILIARY PANEL Pressing the ZONE 2 JETS pad will activate the Power Therapy Seat (see ZONED JETTING for exact location). The ZONE 2 JETS pad will cycle the jet pump from lowspeed to high-speed to off. Pressing the ZONE 2 pad will activate the jets in the remainder of the spa (Zone 2). ED THE R APY SY STE M Z ON ZONE 2 JETS Pump Timeouts Operating sequence is low speed, high speed, then off. If left running, the low speed will turn off after 15 minutes.
500 5 ZONED JETTING 2 E 2 F G H L J 2 2 5 ZONE 1 JETS All jets in seats (E, F, H) and Geyesr jet (G). Press JETS LOW/HIGH pad (2) to turn pump on low-speed. Press JETS LOW/HIGH pad (2) again to turn pump on high-speed (Zone 1A). Adjust the jet pressure with the Air Control Valve (5). Open the Air Control Valve by turning the lever counterclockwise. ZONE 2 JETS All jets (J, K, L). Press JETS LOW/HIGH pad (2) to turn pumps on high-speed. Adjust the jet pressure with the Air Control Valve (5).
500 lx ZONED JETTING ZONED JETTING Spas are divided into different jetting zones. The shaded area of the spa illustration indicates the jets ON in each particular zone. The white area indicates the jets OFF. N 6 L J A compass is used as a directional tool. E S Most jets are adjustable for flow. Many are also adjustable for direction. See OPERATING THE SPA section in the Owners Manual for explanations. 2 5 ZONE 2 JETS All jets in seats (J, K, L).
600 lx 2 E ZONED JETTING 5 F W H W G 5 6 2 6 C C 7 7 ZONE 1A JETS All jets in seats (E, F, H), Cascade Neck jets (C) and Wrist jets (W). Turn Jet Selector Valve to the north. Press JETS LOW/HIGH pad (2) to turn pump on low-speed. Press JETS LOW/HIGH pad (2) again to turn pump on high-speed. Adjust the jet pressure with the Air Control Valve (5). Open the Air Control Valve by turning the lever counterclockwise. Adjust Cascade Neck jets with Neck Jet Valve (7).
700 ZONED JETTING 2 F H 5 G J E K M L 5 ZONE 1A JETS All jets in seats (E, F, H, J) and Geyser jet (G). Press JETS LOW/HIGH pad (2) to turn pump on low-speed. Press JETS LOW/HIGH pad (2) again to turn pump on high-speed. Adjust the jet pressure with the Air Control Valve (5). Open the Air Control Valve by turning the lever counterclockwise. 2 ZONE 2 JETS All jets in seats (K, L, M). Press JPress JETS LOW/HIGH pad (2) to turn pump on high-speed.
700 lx ZONED JETTING 2 F 5 6 H 6 G J E 7 7 C C ZONE 1A JETS All jets in seats (E, F, H, J) and Cascade Neck jets (C). Turn Jet Selector Valve (6) to the north. Press JETS LOW/HIGH pad (2) to turn pump on low-speed. Press JETS LOW/HIGH pad (2) again to turn pump on high-speed. Adjust the jet pressure with the Air Control Valve (5). Open the Air Control Valve by turning the lever counterclockwise. Adjust Cascade Neck jets with Neck Jet Valve (7).
DESTINY Physical Specifications Dimensions Height Depth Seating Positions Weight Dry Lbs. Weight Full Lbs. Water Capacity Total Therapy Jets M A R Q U I S S P A S COASTAL SERIES 84" x 84" 35.
REWARD Physical Specifications Dimensions Height Depth Seating Positions Weight Dry Lbs. Weight Full Lbs. Water Capacity Total Therapy Jets M A R Q U I S S P A S COASTAL SERIES 84" x 84" 35.
EUPHORIA Physical Specifications Dimensions Height Depth Seating Positions Weight Dry Lbs. Weight Full Lbs. Water Capacity Total Therapy Jets M A R Q U I S S P A S COASTAL SERIES 90" x 90" 35.
VOYAGE COASTAL SERIES Physical Specifications Dimensions Height Depth Seating Positions Weight Dry Lbs. Weight Full Lbs. Water Capacity Total Therapy Jets M A R Q U I S S P A S 90" x 90" 35.
COASTAL SERIES CONTROLS Soak Timer: 1st press turns pump to low-speed and star ts 59minute timer; 2nd press “all quiet” mode CL: Clean Filter CH: Change Water C OASTAL S ERIES DUAL-ZONE THERAPY SYSTEM SOAK TIMER ! M AINTENANCE R EMINDERS Light On/Off: 1st press turns underwater and Entryway lights on; 2nd press turns lights off LIGHT ON/OFF 100°F TEMP SET SYSTEM LOCK HEAT MODE FILTER CYCLE Heat On Heat Mode: Standard, Economy or Sleep modes show on LCD display Temp Set: Temperature is displayed
COASTAL SERIES CONTROLS CONSTANT CLEAN™ FILTRATION WITH SMART LOGIC Constant Clean™ Filtration Your spa is automatically preset to filter itself using the jet pump on low-speed for three hours twice in a 24 hour period. The first filter cycle will begin six minutes after the spa is energized. The second filter cycle will begin 12 hours after the first cycle. See PROGRAM FILTER to adjust cycles. Smart Logic 6his feature ensures that the spa water will be properly filtered after each spa use.
COASTAL SERIES CONTROLS TEMPERATURE DISPLAY AND ADJUSTMENT The LCD window displays the actual water temperature. Pressing the TEMP SET pad will make the numbers flash, then pressing the pad again (repeatedly) will increase the set temperature one degree at a time, up to 104° F. After a short pause, the actual temperature will again be displayed. Repeating the above procedure will allow you to decrease the set temperature. HEAT LIGHT The HEAT ON light will illuminate when the heater is on.
COASTAL SERIES CONTROLS Heat On: Illuminates when heat is on Light On/Off: 1st press turns underwater and Entryway lights on; 2nd press turns lights off REMOTE CONTROL HEAT ON TEMP SET FILTER CYCLE LIGHT 100°F SYSTEM LOCK LIGHT ON/OFF CL: Clean Filter CH: Change Water ! M AINTENANCE R EMINDERS C ONSTANT C LEAN F ILTRATION Filter Cycle: 1st press selects Filter Cycle mode; 2nd press chooses cycle FC1,3,6,9; 3rd press Temp Set chooses cycles per day 1C2C; 4th press Filter Cycle adjusts; 5th press
DESTINY ZONED JETTING G 5 2 6 E 5 2 6 C C 7 ZONE 1A JETS Therapy Seat (E) and Cascade Neck Jets (C). Turn the Jet Selector Valve (6) to the north. Press ZONE 1 JETS pad (2) on either panel to turn pump on low-speed. Press ZONE 1 JETS pad (2) again to turn pump on high-speed. Adjust the jet pressure with Air Control Valve (5). Open the Air Control Valve (5) by turning the lever counterclockwise. Cascade Neck Jets (C) are independent of other jets. Control pressure by turning Neck Jet Valve (7).
reward ZONED JETTING G 7 7 E C C 2 6 5 2 6 ZONE 1A JETS Therapy Seat jets (E) and Cascade Neck Jets (C). Turn the Jet Selector Valve (6) to the east and press ZONE 1 JETS pad (2) to turn pump on low-speed. Press ZONE 1 JETS pad (2) again to turn pump on highspeed. Adjust the jet pressure with Air Control Valve (5). Open the Air Control Valve (5) by turning the lever counterclockwise. Cascade Neck Jets (C) are independent of other jets. Control pressure by turning Neck Jet Valve (7).
euphoria ZONED JETTING P 7 7 E C C 6 2 5 6 2 ZONE 1 A JETS All jets (E) and Cascade Neck Jets (C). Turn the Jet Selector Valve (6) to the west and press ZONE 1 JETS pad (2) to turn pump on low-speed. Press ZONE 1 JETS pad (2) again to turn pump on high-speed. Adjust the jet pressure with Air Control Valve (5). Open the Air Control Valve (5) by turning the lever counterclockwise. L ZONE 1B JETS Three Whirlpool Jets (P).
VOYAGE ZONED JETTING p 7 7 E C C 6 2 5 6 2 ZONE 1A JETS Therapy Seat jets (E) and Cascade Neck Jets (C). Turn the Jet Selector Valve (6) to the east and press ZONE 1 JETS pad (2) to turn pump on low-speed. Press ZONE 1 JETS pad (2) again to turn pump on highspeed. Adjust the jet pressure with Air Control Valve (5). Open the Air Control Valve (5) by turning the lever counterclockwise. Cascade Neck Jets (C) are independent of other jets. Control pressure by turning Neck Jet Valve (7).
MARQUIS Physical Specifications Dimensions Height Depth Seating Positions Weight Dry Lbs. Weight Full Lbs. Water Capacity Total Therapy Jets M A R Q U I S S P A S ULTIMATE SERIES 90" x 90" 35.
JOURNEY Physical Specifications Dimensions Height Depth Seating Positions Weight Dry Lbs. Weight Full Lbs. Water Capacity Total Therapy Jets M A R Q U I S S P A S ULTIMATE SERIES 90" x 90" 35.
ULTIMATE SERIES CONTROLS Soak Timer: 1st press turns pump to low-speed and starts 59minute timer; 2nd press “all quiet” mode TRI-ZONE THERAPY SYSTEM SOAK TIMER ! M AINTENANCE R EMINDERS CL: Clean Filter CH: Change Water ULTIMATE SERIES Light On/Off: 1st press turns underwater and Entryway lights on; 2nd press turns lights off LIGHT ON/OFF 100°F TEMP SET HEAT MODE Automated Filtration System FILTER CYCLE Heat On Secured Heat Mode: Standard, Economy or Sleep modes show on LCD display Temp Set: Te
ULTIMATE SERIES CONTROLS CONSTANT CLEAN FILTRATION WITH SMART LOGIC Constant Clean™ Filtration Your spa is automatically preset to filter itself using the jet pump on low-speed for three hours twice in a 24 hour period. The first filter cycle will begin one minute after the spa is energized. The second filter cycle will begin 12 hours after the first cycle. See PROGRAM FILTER to adjust cycles. Smart Logic 6his feature ensures that the spa water will be properly filtered after each spa use.
ULTIMATE SERIES CONTROLS TEMPERATURE DISPLAY AND ADJUSTMENT The LCD window displays the actual water temperature. Pressing the TEMP SET pad will make the numbers flash, then pressing the pad again (repeatedly) will increase the set temperature one degree at a time, up to 104° F. After a short pause, the actual temperature will again be displayed. Repeating the above procedure will allow you to decrease the set temperature. HEAT LIGHT The HEAT ON light will illuminate when the heater is on.
marquis ZONED JETTING P 5 2 6 W P 2 6 E W F ZONE 1A JETS All jets (E, F) and Wrist jets (W). Turn the Jet Selector Valve (6) to the south and press ZONE 1 JETS pad (2) to turn pump on low-speed. Press ZONE 1 JETS pad (2) again to turn pump on high-speed. Adjust the jet pressure with Air Control Valve (5). Open the Air Control Valve (5) by turning the lever counterclockwise. ZONE 1B JETS Two Whirlpool Jets (P).
marquis ZONED JETTING 8 C 7 % P L 6 4 5 ZONE 3A JETS All jets seat (L) and Cascade Neck jets (C). Turn the Jet Selector Valve (6) to the northeast and press ZONE 3 JETS (4) pad to turn pump on low-speed. Press ZONE 3 JETS (4) pad again to turn pump on highspeed. Adjust the jet pressure with Air Control Valve (5). Open the Air Control Valve (5) by turning the lever counterclockwise. C P P 6 4 5 ZONE 3B JETS Four Whirlpool jets (P) and Cascade Neck jets (C).
journey ZONED JETTING 7 F H 7 G C C 6 2 5 6 2 ZONE 1A JETS All jets (F, H) and Cascade Neck Jets (C). Turn the Jet Selector Valve (6) to the north and press ZONE 1 JETS pad (2) to turn pump on low-speed. Press ZONE 1 JETS pad (2) again to turn pump on high-speed. Adjust the jet pressure with Air Control Valve (5). Open the Air Control Valve (5) by turning the lever counterclockwise. Cascade Neck Jets (C) are independent of other jets. Control pressure by turning Neck Jet Valve (7).
journey 7 ZONED JETTING H C 6 4 5 ZONE 3A JETS All jets (H) and Cascade Neck jets (C). Turn the Jet Selector Valve (6) to the west and press ZONE 3 JETS (4) pad to turn pump on low-speed. Press ZONE 3 JETS (4) pad again to turn pump on high-speed. Adjust the jet pressure with Air Control Valve (5). Open the Air Control Valve (5) by turning the lever counterclockwise. Control Cascade Neck jet pressure with valve (7). M A R Q U I S S P A S • l N W Shaded area: Jets On. White area: Jets Off.
SPA MAINTENANCE EXTERIOR Depending upon your choice of a natural cedar or DuraWood exterior, there are several routine maintenance steps you should follow. Wood Exterior: The wood exterior has been treated with a waterbased wood preservative at the factory. It is suggested that the exterior be treated every six months with an additional coat of preservative for maximum weather protection. Your Dealer can suggest the best preservative for your environment and also provide the Super Deck Wood Care Kit.
SPA MAINTENANCE (CONTINUED) Dura Base External Drain and Fill Valve 1. Remove plug from the external Drain and Fill valve. 2. Attach a hose to the external drain and fill valve on the J DuraBase. A Fill Filter is recommended when filling. Attach to the end of a garden hose to filter out any grit and sediment that may accumulate in the spa and potentially scratch the spa surface during the process. 3. Open the valve by turning the ring counterclockwise.
SPA MAINTENANCE (CONTINUED) LIGHT BULB REPLACEMENT To replace a bulb for the Entryway or Underwater lighting, 1. Remove the equipment area door to find the light access. 2. Remove the lamp socket from the back of the light assembly by turning counterclockwise and pulling at the same time. 3. Gently pull the bulb out of the lamp socket and replace it with a 6 WATT BULB ONLY from your spa retailer. 4. Install the lamp socket back into the light assembly and replace door.
SPA MAINTENANCE SCHEDULE DAILY Replenish the water level by filling 2/3 up the Vortex skimmer opening(s). (See STARTING YOUR SPA section.) Check the water balance. Adjust as needed. WEEKLY Wipe down the embossed tile. Remove the filter cartridge(s) and rinse thoroughly with a hose and high-pressure nozzle. MONTHLY Soak the filter cartridge(s) in Marquis Spa Care Filter Revive. Rinse thoroughly in clean water. Clean the spa Safety Energy Cover with Marquis Spa Care Cover Cleaner.
○ ○ Misc.
TROUBLESHOOTING PLEASE NOTE: The following corrective actions may be performed by the spa owner. If the trouble cannot be corrected in the steps below, please refer to your spa retailer for service. (Improper servicing by an unauthorized service provider or spa owner could result in damage that will not be covered by the warranty and could cause serious injury.) EQUIPMENT WILL NOT OPERATE Check the control panel LCD display code. 240V Spas: Check the circuit breaker on the main circuit panel.
TROUBLESHOOTING LCD DISPLAY MESSAGES (CONTINUED) SN, Snt or SnH: A sensor has malfunctioned. The spa will turn off. Contact your service provider. CL: CH: FL: This will appear every 30 days as a reminder to clean the filter. (See REMOVING THE FILTER.) This will appear every 90 days as a reminder to drain and refill the spa. (See DRAINING THE SPA and REFILLING.) A pressure switch may have malfunctioned. Contact your service provider. NO HEAT Check temperature LCD display for desired temperature setting.
TROUBLESHOOTING (CONTINUED) SPA WATER MAINTENANCE Maintaining proper water chemical balance is critical to your health and enjoyment. Marquis recommends that you use an ozonator (optional on Leisure and Recreational Series, standard on Coastal and Ultimate Series) along with the proper supplemental sanitizer. Marquis offers a complete line of Marquis Spa Care products which meet or surpass Environment Protection Agency (EPA) requirements.
TROUBLESHOOTING (CONTINUED) SPA WATER MAINTENANCE (CONTINUED) SCUM LINE IN SPA C: Body oils and dirt. S: Use Spa Perfect once a week to break down oils and lotions to prevent scum from forming. FAILURE TO GET A SANITIZER READING ON TEST STRIP C: Sanitizer level is too low. S: Add chlorine or bromine until the sanitizer tests in the recommended range. C: Algae present. S: Dirty water will consume the sanitizer as soon as it is added.
R E L A X I N G Y O U R W O R M a r qu i s C or p. 596 Hof f ma n Roa d • I n de pe n de n ce , OR 9 7 3 5 1 8 0 0 . 2 7 5 . 0 8 8 8 • www.marquisspas.com ©COPYRIGHT MARQUIS CORP.
