get into it! owner’s manual WELCOME TO THE SPA LIFE! Please enjoy your new Everyday Hot Tub, but think safety first. Read your Owner’s Manual in its entirety before installing your spa and encourage all spa users to do the same. More than just common sense, this Owner’s Manual provides vital safety and operational information. We sincerely hope your spa life is a pleasant experience. If problems should arise, contact your Everyday Hot Tubs™ dealer. Or contact Marquis Corp.
get into it! product reference SERIAL NUMBER LOCATION You will find the serial number on the silver tag in the equipment area.
get into it! owner’s manual index IMPORTANT SAFETY INSTRUCTIONS 120V, Cord Connected Models ....................................................... 4 240V, Permanently Installed or Converted Models ....................... 5 Safety ................................................................................................. 6-9 INSTALLATION INSTRUCTIONS Location ............................................................................................. 10-11 Filter Cartridge .........................
get into it! safety instructions The following instructions are required to be printed by Underwriters Laboratories (UL) as a condition of the listing of this product. They contain important safety information. We strongly encourage you to read and apply them. IMPORTANT SAFETY INSTRUCTIONS WHEN INSTALLING AND USING THIS ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING: 1. READ AND FOLLOW ALL INSTRUCTIONS 2.
get into it! safety instructions 240 VOLT, PERMANENTLY INSTALLED OR CONVERTED MODELS 9. A ground terminal is provided on the terminal block (TB-1, terminal 7) located inside the control box. To reduce the risk of electric shock, connect this terminal to the grounding terminal of your electrical service or supply panel with a continuous green, insulated copper wire. The wire must be equivalent in size to the circuit conductors supplying the equipment.
get into it! safety instructions • Persons suffering from obesity or with a medical history of heart disease, low or high blood pressure, circulatory system problems, or diabetes should consult a physician before using the spa. • Persons using medications should consult a physician before using a spa since some medication may induce drowsiness while other medication may affect heart rate, blood pressure, and circulation. 15.DANGER: TO REDUCE THE RISK OF INJURY TO PERSONS.
get into it! safety instructions SAFETY INSTRUCTIONS FOR FRENCH SPEAKING SPA OWNERS AVERTISSEMENT: Ne pas placer d’appareil électrique (luminaire, téléphone,radio, téléviseur, etc.) moins de 1.52 m de cette cuve de relaxation. AVERTISSEMENT: Ne pas laisser les enfants utiliser une cuve de relaxation sans surveillance.
get into it! safety instructions PERSONAL SAFETY Prolonged immersion in hot water can result in HYPERTHERMIA, a dangerous condition which occurs when the internal temperature of the body reaches a level above normal (98.6°F, 37°C). The symptoms of hyperthermia include dizziness, fainting, drowsiness, lethargy, and a body temperature above 98.6°F (37°C).
get into it! safety instructions PERSONAL SAFETY DOs: • Be sure your spa is connected to the power supply correctly – only use a licensed electrical contractor. • Shut off power supply (unplug 120V models) before draining the spa or servicing the electrical components. • Test the Ground Fault Circuit Interrupter (GFCI) monthly. • Always test the water temperature with an accurate thermometer before entering the spa to be sure that it’s a safe temperature. • Remember that wet surfaces can be very slippery.
get into it! installation instructions LOCATION For your portable spa to function properly and safely, it must be located on a hard, flat, level surface. Inground spas require special installation techniques and should be planned in conjunction with your spa dealer. Improper installation can result in structural damage to the spa and the voiding of your spa warranty.
get into it! installation instructions OUTDOOR AND PATIO INSTALLATION To install the spa outdoors, we recommend a reinforced concrete pad at least four inches thick. The reinforcing material should be attached to a #8 AWG bonding wire per national and local electrical code. If you place the spa on the ground, even temporarily, place concrete pavers under the entire bottom of the spa. The concrete pavers should be a least two inches thick and level across the entire surface.
get into it! installation instructions SHUT-OFF VALVES Your spa is equipped with shut-off valves (see EQUIPMENT DIAGRAM) that shut off the water flow to the equipment system for dealer service. At times, a new spa or one that has recently been serviced, may have the shut-off valves partially closed which can restrict the water flow and hinder jet performance. Be sure the valves are fully open.
get into it! Safety guard of suction fitting must remain in place. installation instructions SUCTION GUARDS The suction guard(s) in the footwell of your spa is an opening through which the jet pump draws water. Suction fittings are equipped with a safety guard. Suction through the fittings can be strong. The safety guard(s) must remain in place and undamaged. A fitting with a damaged guard(s) can be dangerous, especially to small children or people with long hair.
get into it! starting your spa START-UP PROCEDURE Your spa is equipped with solid-state Comfort Controls specific to your spa model. Please see SPA CONTROL OPERATION for your specific spa model. To start your spa, you need a spa water test kit and an underwater thermometer. It is important to follow each of these steps when starting your spa. Once you have completed the following steps, refer to the WATER TREATMENT section for proper start-up water maintenance. Marquis SpaCare products are recommended.
get into it! Use TEMP pad to set water temperature. starting your spa 6. Turn the power on and wait five seconds. 7. After a few seconds the spa should have water flowing from the jets. If the pump has not primed and the water is not flowing from the jets after two minutes TURN OFF POWER TO THE SPA and vent air from the pumps by slightly opening the pump unions. (SEE EQUIPMENT DIAGRAM). 8. The factory default setting for water temperature is 102°F (39°C).
get into it! operating your spa MAXIMUM THERAPY JETTING SYSTEM ISO BOOST JETS This small jet provides a targeted stream of water. POWER BOOST JET The direction of water flow can be changed by redirecting the central nozzle. The water flow can be adjusted by turning the jet face using the four tabs. Power swirl jet POWER SWIRL JET This rotating jet provides a firm, broad area of circular massage. The water flow can be adjusted by turning the jet face using the four tabs.
get into it! 5 Use the Bather’s panel to set the temperature, select the filtration, and turn on the jets and lights. 11 This valve controls the water flow of the Cascade Neck jets. the 530 # 1 2 3 4 Component Identification Iso Boost Jets Power Boost Jets Power Swirl Jets Cascade Neck™ Jets Qty.
get into it! 5 Use the Bather’s panel to set the temperature, select the filtration, and turn on the jets and lights. 11 This valve controls the water flow of the Cascade Neck jets. the 415 # 1 2 3 4 Component Identification Iso Boost Jets Power Boost Jets Power Swirl Jets Cascade Neck™ Jets Qty.
get into it! 2 the 210 Use the Bather’s panel to set the temperature, select the filtration, and turn on the jets and lights. # 1 2 3 4 Component Identification Iso Boost Jets Bathers Control Panel Heat Sensor Filter Canister Qty. 10 1 1 1 5 6 7 Suction Fittings Floor Drain Light 2 1 1 Physical Specifications Dimensions Height Interior Depth Seating Positions Weight Dry/Lbs. Weight Full/Lbs. Water Capacity/Gallons Total Therapy Jets 19 Size 68" x 68" 29.
get into it! spa control operation MODELS 530, 415, 210 LIGHT UNDERWATER LIGHT Press the LIGHT pad to turn the underwater light on and off. The low-voltage system produces a night light for evening use and makes entering and exiting the spa safer. After being on for 30 minutes, the light automatically turns off. OPTIONAL WATERCOLORS™* Press LIGHT pad to turn on step one. Press LIGHT pad again to turn off for one second. Then press LIGHT pad again for step two. Repeat for all color options.
get into it! spa control operation CONSTANT CLEAN™ WATER MANAGEMENT WITH SMART LOGIC™ Factory Default Settings: • Filter Cycle Duration: F2 (2 hours) • Filter Cycles: 2C (twice per day) • Smart Logic: 1H (1 hour) These settings represent the most commonly used settings, but your use may be different, depending upon many variables – frequency, number of bathers, duration, water capacity, etc.
get into it! TEMP+- SETTINGS spa control operation Use the TEMP+- pad to scroll through filter cycle options. When desired selection has been reached, press the SETTINGS pad to enter selection and advance to the Smart Logic™ settings.
get into it! spa control operation pause, the actual temperature displays. Press TEMP- pad repeatedly to decrease the set temperature to 80°F (27°C). *NOTE: In event of a power outage, all settings revert to the preset, default settings. HEAT LIGHT The HEAT light illuminates when the heater is on. The pump circulates on low-speed whenever the thermostat calls for heat.
get into it! equipment diagram MODEL 530 24 # 1 Component Control box and heater Part # (650-0571) Qty.
get into it! equipment diagram MODEL 415 & 210 10 25 # 1 Component Control box and heater Part # Qty.
get into it! troubleshooting PLEASE NOTE: The following corrective actions may be performed by the spa owner. If the trouble cannot be corrected in the steps below, please contact your Everyday Hot Tubs™ dealer for service. (Improper servicing by an unauthorized service provider or spa owner could result in damage not covered by the warranty and could cause serious injury.) EQUIPMENT WILL NOT OPERATE • Check the control panel LCD window for diagnostic code.
get into it! troubleshooting LCD DIAGNOSTIC MESSAGES The advanced technology built into the spa allows it to perform a number of self-diagnostic system checks and it can display a variety of messages in the LCD window on the control panel. CL: This appears every 30 days as a reminder to clean the filter. (See INSTALLATION INSTRUCTIONS, Filter Cartridge.) CH: This appears every 90 days as a reminder to drain and refill the spa. (See SPA MAINTENANCE, Draining and Filling the Spa.
get into it! maintenance WEEKLY MAINTENANCE 1. Removing Debris Remove any debris from the Vortex skimmer and suction guard(s) on the inside of the spa. Blocked intakes can impede the flow of water through the jetting system. Water level should be two-thirds up the Vortex skimmer opening. 2. Water Level Replenish the water level if necessary so that it is approximately two-thirds up the Vortex skimmer opening. (See STARTING YOUR SPA.) MONTHLY MAINTENANCE 1.
get into it! maintenance Reinstalling the Filter Repeat the steps above in reverse. Do not overtighten the filter as it may cause the threads on the bottom to strip and fail to hold the filter in place. When replacing the Vortex filter top, center the top over the raised filter ring and press down firmly until the top snaps into place. (See INSTALLATION INSTRUCTIONS, Filter Cartridge.) EVERY THREE TO FOUR MONTHS Draining and Filling the Spa The average spa needs to be drained every three to four months.
get into it! maintenance AS NEEDED MAINTENANCE Marquis Maintenance Kit includes: DuraWood Cleaner, Cover Care Cleaner, Fill Filter, Filter Revive, Swirl Away Plumbing Cleaner, interior DuraMitt, and a scrubby hand mitt for exterior cabinet and cover cleaning, all in a handy storage bucket. 1. Cover Care It is recommended that you use Marquis Cover Care Cleaner to keep the spa cover clean and conditioned.
get into it! maintenance C. Remove the lamp socket from the back of the light assembly by turning counterclockwise and pulling at the same time. D. Gently pull the bulb out of the lamp socket and replace it with a 6 watt bulb only (GE #918) available from your spa dealer. E. Install the lamp socket back into the light assembly and replace door.
get into it! spa care and enjoyment guide IMPORTANT CHEMICAL SAFETY PROCEDURES 1. Always keep chemicals out of reach of children. 2. Read product labels carefully prior to use. 3. When dissolving, always add chemicals to water, do not add water to chemicals. Some dry chemicals should be dissolved prior to adding them to the spa. Using a clean container, dip some water from the spa. Mix until dissolved, then add to circulating water. 4. CAUTION: Do not add chemicals together.
get into it! spa care and enjoyment guide UNDERSTANDING WATER BALANCE Water balance is the interrelation of factors that determine the quality of the spa water. The effectiveness of chemicals and other additives are dependent on all these factors working together or “in balance”. The primary elements to water balance are sanitizing, monitoring pH and alkalinity levels, and oxidizing or shocking.
get into it! spa care and enjoyment guide pH Level The pH level measures the relative acidity and basicity of the water. The ideal pH level is 7.2 - 7.8. When the pH level falls below 7.2 the water can become corrosive. Low pH can cause damage to metal in the equipment pack and heaters, excessive sanitizer consumption, and skin irritation. A pH level above 7.8 can be scale-forming and allows metals or minerals in the water to form deposits and stain spa surfaces.
get into it! spa care and enjoyment guide Balancing the Water When initially filling or refilling your spa follow these steps to achieve proper water balance. Important! Always circulate the water for at least 15 minutes after making any chemical additions, before retesting water, or adding any additional products. 1. Test the spa water using a Test Strip (see label for easy dip and read directions). 2. Determine the pH and alkalinity level of the water using the color comparison chart on the bottle. 3.
get into it! spa care and enjoyment guide Metal and Stain Control If minerals such as calcium, iron, copper, or manganese exist in your water supply, they can stain spa surfaces. Metal & Stain Control prevents spa staining. Add per label directions for the gallons of your spa each time you freshly fill the spa with water. Calcium Hardness Increase It is critical to have some calcium in your water, however, the level of calcium should be between 200 – 400 ppm.
get into it! spa care and enjoyment guide WATER CARE REGIMEN Spa care products are classified by easy to follow usage guidelines. The information below indicates whether the product should be used daily, weekly, monthly, when filling, or as needed – if special water conditions arise. (Products classified as “Filling” are described on the previous page.) DAILY Sanitizer is the only product in this category. You should maintain the recommended sanitizer level at all times.
get into it! spa care and enjoyment guide AS NEEDED PRODUCTS pH & Alkalinity Increase and pH & Alkalinity Decrease These two products work to raise or lower the pH and alkalinity levels in the spa and are only needed if the test strip indicates the levels are not in the ideal range. Clarifier Microscopic particles can pass right through the spa filter and create cloudy water.
get into it! spa care and enjoyment guide TROUBLESHOOTING GUIDE C: Cause S: Solution CLOUDY WATER C: Inadequate filtration or dirty filter. S: Check that the filter is securely installed. Clean or replace filter. C: Water is not balanced. S: Treat water with Shock and test water with a Water Test Strip. Adjust sanitizer level, pH, and alkalinity levels as needed. C: Unfiltered particles or chemically saturated water. S: Use Clarifier to combine particles; or drain, clean, and refill the spa.
get into it! spa care and enjoyment guide FAILURE TO GET A SANITIZER READING ON TEST STRIP C: Sanitizer level is too low. S: Add chlorine or bromine until the sanitizer registers in the recommended range on the test strip. C: Algae present. S: Dirty water consumes the sanitizer as soon as it is added. Add more chlorine or bromine until the sanitizer registers and stays in the recommended range on the test strip. C: Test strip remains “white” even after sanitizer has been added.
get into it! Everyday Hot Tubs limited warranty LIMITED WARRANTY SPA SHELL, SPA SHELL LEAKS, AND STRUCTURE Marquis Corp. warrants the spa shell against peeling, cracking, yellowing, blistering, or delamination for a period of five years from date of purchase. Spa shell and structure are warranted against leaks for a period of five years from date of purchase. SPA CABINET AND SPA BASE Marquis Corp.
get into it! Everyday Hot Tubs limited warranty LIMITED WARRANTY In order to obtain the benefit of this warranty, the spa owner shall notify their authorized Everyday Hot Tubs™ dealer of any problem or warranty claim within thirty days of the time the problem is discovered. In the event the spa owner is unable to obtain parts or service from an authorized Everyday Hot Tubs dealer, the spa owner should notify the Customer Service Department of Marquis Corp.
get into it! Everyday Hot Tubs limited warranty Other items not included in this warranty are freight expense; labor and material costs associated with removal and/or replacement of spa; damage to the spa surface and equipment due to the use of trichlor chlorine or other harsh chemicals not recommended by Marquis Corp.
