Installation Instructions Gas Fired Direct Vent Room Heater Inserts Listed Certified for USA.
Pre-installation Questions and Answers About curing of the paint Your stove or fireplace has been painted with the highest quality silicone stove paint. This paint dries quickly in 15-20 minutes when first applied at the factory. However, due to the high temperature silicone components, the paint will cure when heat is applied to the appliance as it is first used. The following information applies to the curing process to get the paint fully hard and durable.
Table of Contents Pre-installation Questions and Answers............................................................................................................... Operating Instructions........................................................................................................................................... Table of Contents.................................................................................................................................................
Millivolt System, Lighting, and Burner Control...................................................................................................... IDV26 Remote Receiver Location........................................................................................................................ IPI Electronic Ignition System............................................................................................................................... Electronic Ignition Lighting Instructions.............
Mobile Home/Manufactured Housing Installation This Direct Vent System Appliance must be installed in accordance with the manufacturer’s installation instructions and the Manufactured Home Construction and Safety Standard Title 24 CFR, Part 3280, or the current Standard for Fire Safety Criteria for Manufactured Home Installation, Sites, and Communities ANSI/NFPA 501A, and with CAN/CSA Z240 MH Mobile Home Standard in Canada. THIS APPLIANCE MAY BE INSTALLED IN MANUFACTURED (MOBILE) HOMES AFTER FIRST SALE.
Warnings, Installations and Operations Installation Regulations This gas appliance must be installed by a qualified installer in accordance with local building codes, or in the absence of local codes, with the current CAN/CSA-B149.1 or .2 Installation Code (in Canada) or the current National Fuel Gas Code Z223.1- NFPA 54 when installed in the United States.
• Gas fired appliances may be used only for supplemental heat and/or decorative purposes and under no circumstances shall they provide a primary heat source. • This appliance must not be connected to a chimney flue serving a separate solid-fuel burning appliance. NOTE: It is recommended that a Carbon Monoxide (CO) Detector be installed in or near bedrooms and on all levels of your home. Place a detector about 15ft [4.5m] outside the room that houses your gas appliance.
Important Information INSTALLATIONS The following label (supplied with the gas fireplace insert) must be attached with rivets or screws to the inside of the firebox of the fireplace into which it is installed: Cutting any sheet-metal parts of the fireplace, in which the gas fireplace insert is to be installed, is prohibited. If the factory-built fireplace has no gas access hole(s) provided, an access hole of 1.5 in (37.
IDV26 Insert Dimensions and Sizing Minimum Opening Dimensions Dimension “A” Front Width: “B” Height: “C” Depth: “D” Back Width: “D” “B” “C” “A” Components Out Components In 33” Centered in existing fireplace *31” Not Centered in existing fireplace 19-1/2” 14-1/4” 22” 28” 19-1/2” 14-1/4” 22” Note: Valve Control Components can be placed either inside the opening (Components In) or outside the opening (Components Out). Units are shipped with Control Components in.
I26CV Clean View and Surround Sizes *The Clean Views and Surrounds in this section must be used with Valve Control Components inside the opening (as shipped).
I26CV1DS IDV26 *The Clean View Designer Door and optional surround in this section must be used with Valve Control Components inside the opening (as shipped).
IDV26 I26SU Universal Surround A Universal Surround is available for the IDV26. This is provided as a flat sheet which mounts onto the unit and is to be cut to size and formed by the installer. Flat Surround Shown dimensioned. Components In Components Out 7” I26SU installed on unit. Picture Frame Clean View Kit I26CVPF1 With Universal Surround I26SU I26SU must be trimmed to fit around Valve Control Components.
I26CVPF2 I26SU UNIVERSAL SURROUND I26CVPF BOTTOM OF UNIT 13
I26CV - Surround Installation -Clean View (CV) Attachment -Valve Access 1. Optional Surround Kit (I26S, I26SPF, I26SU) is fastened to the insert by pulling up [4] Surround Mount Tabs on the unit and using [4] #6 screws provided with surround. 2. Insert the Clean View (I26CV1, I26CV2, I26CVPF1, I26CVPF2, I26CV1DS) Mounting Tab into the Clean View Mounting Slots (four [4] places) and lower the Clean View kit into place. 3. Valve Access: To access valve simply remove Clean View.
I26S1 / I26SPF1 / I26SU Surround Installation Component List: I26S1 / I26SPF1 / I26SU Surround, [Qty 4] #6 Black Combo Screws Bend Up All 4 Mount Tabs Top Left Top Right Bottom Left Bottom Right Place Surround onto unit and line up holes in mount tabs with holes in Surround. Attach with screws provided.
I26CV2 / I26CVPF2 Wide Clean View Installation Component List: I26CV2 or I26CVPF2 Clean View On/ Off Switch Extension Bracket Fan Control Switch Extension Bracket [4] #6 Black Combo Screws Components In (As Shipped): Fan Control Switch Bracket On/Off Switch Bracket Remove On/Off Switch and original mount bracket. Remove Fan Control Switch From Current Position. Attach Fan Control Switch Extension Bracket using [2] #6 Combo Screws as shown.
I26CV2 / I26CVPF2 Wide Clean View Installation -Components Out- Fan Control Switch Bracket On/Off Switch Bracket NOTE: If Ground is attached to Side Component Plate, remove and fasten to side of appliance with a DT Screw. Remove Fan Control Switch From Current Position. Remove On/Off Switch and original mount bracket. Attach Fan Control Switch Extension Bracket using [2] #6 Combo Screws. Attach On/ Off Switch Extension Bracket using [2] #6 Combo Screws as shown. Mount Switch & route wiring as shown.
IDV33 Insert Dimensions and Sizing Min. Coverage with Optional I33LK or I33CV Base Unit I33LK I33CV 26-1/4” 34-1/2” 32-3/4” 21-1/4” 21-1/4” 21-1/4” 21-3/8” 24-3/8” 22-3/4” 14-3/8” 18-3/8” 16-3/4” Unit Sits Proud of Finished Surface 2-1/2” with CV Kit, and 4” with LK Kit.
I33LK Louver Kit and Surround Sizes NOTE: The Surrounds shown here are universal and can be used with the I33CV model. Furthermore, the I33S4535B and I36S4736B (1-piece Surround) was designed to be used as a custom cutout surround. Simply trace template and cut out design using the universal surround.
IDV36 Insert Dimensions and Sizing Min. Coverage with Optional I36LK or I36CV Base Unit I36LK I36CV 30-3/4” 39” 37-1/4” 25-3/4” 25-3/4” 25-3/4” 25-5/8” 28-3/4” 27” 14-3/8” 18-3/8” 16-3/4” Unit Sits Proud of Finished Surface 2-1/2” with CV Kit, and 4” with LK Kit.
I36LK Louver Kit and Surround Sizes NOTE: The Surrounds shown here are universal and can be used with the I36CV model. Furthermore, the I33S4535B and I36S4736B (1-piece Surround) was designed to be used as a custom cutout surround. Simply trace template and cut out design using the universal surround.
I33CV/I36CV Front Face and Surround Attachment Installation 1. Remove the Top Filler Panel to install vent adapter and venting to the unit. Once this is done, reinstall the Top Filler Panel. Refer to Installation of Vent Pipe for venting information. 2. Install ON/OFF switch into the slot provided located at the lower left hand side of the appliance. 3. If the Optional Surround Kit is being used then fasten them to the Clean View kit with the seven [7] screws provided. 4.
I33LK/I36LK Front Face Attachment Installation 1. Remove the Top Filler piece from the Base unit by unfastening its three [3] screws. This part is not required for the I33LK/I36LK model and therefore can be discarded. However, be sure to keep the screws for fastening the I33LK/I36LK. 2. Install Vent Adapter plate. Please see Installation of Vent Pipe for reference. 3. Remove ON/OFF switch & wires from valve (make note of connections first). Set aside until LK Front is attached. 4.
Surround Installation for IDV33/IDV36 Fronts 1. Ensure that the I33LK/I36LK Front is installed before continuing with these steps. 2. When installing a 3-piece surround, please note that the side panels must go first. When installing a 1-piece surround, simply skip the instructions for the side panel installation. 3. Slide side panels in place. Make sure the pre-set screws slide into the slots located behind the side columns. Do not tighten these screws yet. You will need to line up the top panel first. 4.
IDV26 / IDV33 / IDV36 Wall Coverings All wall coverings below Combustible Mantel Line MUST be Non-Combustible (e.g. steel studs and concrete board). CV Surround (IDV26 This Side Only) IDV26 Hearth Pad (if used): Requires ½” thick noncombustible (I.e. concrete board) 15” out and 31” wide. All wall coverings closer than Combustible Materials Line MUST be NON-Combustible. (IDV26 This Side Only) *For more information see Clearance to Combustible Mantels Page.
IDV26/IDV33/IDV36 Clearance to Combustible Mantels Before installing any mantels it is important to determine the combustibility of its material(s). There are two types of mantel materials to consider: Combustible and Non-combustible. A Combustible Mantel is one that consists of material(s) that may discolor, combust, or lose its integrity in the presence of heat. These types of mantel must strictly adhere to the dimensional requirements shown in the figures below.
IDV26 / IDV33 / IDV36 Venting Vertical Venting in Cold Climates In cold climate conditions where temperatures go below -10°C [14°F], we recommend that the chase be insulated and where the vent pipe enters into the attic space that the pipe be wrapped with an insulated Mylar sleeve. This will increase the temperature of the vent and help the appliance to vent properly in cold weather conditions.
IDV26 / IDV33 / IDV36 Installation of Vent Pipe 1. Remove the Top Filler and adapter plate from the unit by removing the five [5] screws as shown below. (Fig. 3) Attach the vent pipes to the termination with Millpac and 4 screws per pipe joint. Be sure to label the exhaust and intake flex pipes. Make sure not to connect the exhaust to the intake or vice-versa. Lower the termination and vent pipe down the vent and screw and seal plate to the chimney crown, clay tile chimney or wood stove vent.
Insulation of Chimney Cavity IDV26 / IDV33 / IDV36 If You Live In A Cold Climate Zone And Your Chimney Is On The Side Of Your House In cold climates, especially where the chimney is located on the outside of the home it may be necessary to insulate the chimney cavity with NONCOMBUSTIBLE insulation such as vermiculite or Roxul insulation. This will keep the chimney cavity warm and avoid cold start ignition problems. FOLLOW ALL LOCAL CODES. NON-COMBUSTIBLE INSULATION (Vermiculite, etc.
IDV26 / IDV33 / IDV36 Riser Kit and Leveling Instructions Leveling Instructions When installing insert it may be necessary to support back of unit. To support back of insert, there are two leveling plates right and left of unit. 1. Measure height required to level unit. 2. Remove two [2] outer screws and loosen center screw holding each plate into position. 3. Slide plates to the required height and align with appropriate holes. Each set of holes equals to a 1/4” of movement up to a maximum of four inches.
IDV26 / IDV33 / IDV36 Glass Door Information Glass Cleaning It will be necessary to clean the glass periodically. During start-up condensation will form, and cause dust and lint to cling to the surface of the glass. Furthermore, the initial burn cures the paint but also leads to the deposit of a filmy residue. It is therefore recommended that the glass be cleaned two or three times, initially, with non-abrasive common household glass cleansers and warm water.
IDV26PRL - Porcelain Liner Panels- IDV26PL Parts List: -1 Back Panel -1 Right Side Panel -1Left Side Panel Side Panel To Remove: 1. Remove Log Supports. Remove the [5] screws in the firebox top holding the Baffle in place. 2. Remove Back Panel. Unscrew and remove the Back Panel. Slide and tilt to remove. NOTE: If you will be installing a porcelain Back Liner, unscrew Back Panel Air Deflector and install on porcelain Back Liner. Back Panel 3. Remove Side Panels (if present). Remove screw.
IDV26RL IDV26RL Parts List: -1 Back Panel -1 Right Side Panel -1Left Side Panel - Brick Liner Panels- Liner Retainer Clip To Install: 1. Remove the Baffle. Remove the [5] screws in the firebox top holding the Baffle in place. Remove the [2] Liner Retainer Clips in the firebox top also. Side Panel 2. Install Back Panel. Place Back Panel on the rear ledge inside the firebox. 3. Install Side Panels. Twist and rotate Side Panels into place. Secure with Liner Retainer Clips in top of firebox.. 4.
IDV33 / IDV36 Brick Liner and Liner Panel Installation Instructions For IDV33 & IDV36 Brick Liners 1. Remove the glass door. If a flat black rear panel has been installed on the back of the firebox, remove the rear panel. (see below). 2. Install rear brick panel first. 3. Install left and right side panels and secure them with brick clips. 4. Once the brick panels are secured, reinstall the glass door. Refer to Glass Door Information.
IDV33/36PRL- Removing and Installing Generation 2 Liner PanelsParts List -1 Back Panel -1 Right Side Panel -1Left Side Panel To Remove: 1. Lift Log Supports out of fireplace. 2. Remove the 2 Screws in the Back Panel. 3. Slide and tilt Back Panel to remove. 4. To remove Side Panels (if present) remove screw in top of Side Panel and tilt and slide out of fireplace. Log Supports Back Panel To Install: 1. Place Back Panel up against the back of the Firebox and reinstall the 2 Screws. 2.
IDV33/IDV36 Overlay and Double Door Installation IDV33 Overlay This style of Overlay mounts in the square notch cutout as shown in the illustration to the right. Use magnets to secure the overlay to the glass door frame. IDV36 Overlay This style of Overlay mounts to the latching system. It sits on top of the door latch and is secured using a steel pin. The lower portion of the overlay is held to the surface of the door frame with magnets. 1.
Gas Line Installation This gas appliance should be installed by a qualified installer in accordance with local building codes and with current CAN/CSA - B149.1 installation codes for Gas Burning appliances and equipment in Canada and the National Fuel Gas Code ANSI Z223 in the U.S.A. State of Massachusetts For the state of Massachusetts a T-handle gas shut-off valve must be used on a gas appliance. This T-handle gas shut-off valve must be listed and approved by the state of Massachusetts.
IDV33 / IDV36 Burner Installation/Removal Burner System 1. Remove glass door assembly and logs (if installed). Be careful with logs as they become fragile after being heated. 2. Remove log supports off burner assembly. 3. The burner or burner assembly can now be removed. a. TO REMOVE H-BURNER/ORIFICE CHANGE - Remove the two [2] screws holding the H-Burner in and slide it leftwards off the orifice. b. TO REMOVE BURNER ASSEMBLY Locate and remove the twelve [12] screws around the outside of the burner pan.
IDV26 Burner Installation/Removal CAUTION Before servicing the burner system ensure that the gas supply is turned OFF and disconnect all electrical connections to the appliance. Allow the appliance to cool to room temperature. Note that the pilot assembly may be hot in an intermittent or standing-pilot system—even if the main burner was never on. Exercise caution when working within the area. ALL WORK SHOULD BE PERFORMED BY A QUALIFIED AND CERTIFIED TECHNICIAN.
IDV26 -Millivolt- -Control Components Outside the Opening- -COMPONENTS OUT- Warning: Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this appliance may result in property damage or personal injury. NOTE: It is not necessary to disconnect pilot lines and gas supply line from valve to complete this procedure. Care should be taken to ensure that the gas and pilot lines are not damaged during handling. These lines are fragile.
Attach Component Panel Fasten Component Panel [2] Screws Replace Side Plate Extended Switch Bracket 7. Fasten Component Panel at top. Replace Side Plate. Attach 8. Component Panel and 9. Procedure is complete. Extended Switch Bracket. IDV26 -IPI- -Control Components Outside the Opening- -COMPONENTS OUT- *Refer to Millivolt section for more detailed photos & instructions. Component Panel 1. Ready to begin. All Components from Component Panel. 2. Remove Remove Component Panel from fireplace.
Fasten to Component Panel with Zip Tie. 5. 6. Replace Side Plate. Fasten Component Panel at top & bottom. Attach Component Panel and Extended Switch Bracket (see millivolt section). MILLIVOLT- COMPONENTS OUT Procedure is complete.
IDV26 Fan Speed Control Outside COMPONENTS OUT Warning: Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this appliance may result in property damage or personal injury. NOTE: It is not necessary to disconnect fan wiring to complete this procedure. This procedure must be done before the unit is inside the enclosure. Remove Component Panel [1] DT Screw Remove Fan Switch 2. Connect Fan Switch to Extension Bracket. 1.
IDV26 Optional Fan Removal / Installation WARNING Electrical Grounding Instructions This appliance is equipped with a three prong (grounding) plug for your protection against shock hazard and should be plugged directly into a properly grounded three-prong receptacle. Do not cut or remove the grounding prong from this. Before Servicing 1. 2. 3. Ensure all power supply is shut off. Label all wires prior to disconnecting when servicing control. Wiring errors can cause improper and dangerous operation.
IDV26 Fan - Wiring IDV26 45
IDV33 / IDV36 Fan Installation/Removal IDV33 / IDV36 Fan System WARNING Electrical Grounding Instructions This appliance is equipped with a three prong (grounding) plug for your protection against shock hazard and should be plugged directly into a properly grounded three-prong receptacle. Do not cut or remove the grounding prong from this. Before Servicing 1. Ensure all power supply is shut off. 2. Label all wires prior to disconnecting when servicing control.
IDV33/IDV36 Insert Burner Component List ITEM NO. PART DESCRIPTION Qty.
Millivolt System, Lighting, and Burner Control FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A B BEFORE LIGHTING This appliance has a pilot which must be lighted by hand. When Immediately call your gas supplier from a neighbour’s phone. Follow the lighting the pilot, follow these instructions exactly. gas supplier’s instructions.
IDV26 Remote Receiver Location All Units Connecting to the Gas Valve The wiring harness for the Proflame GTM system has two wires labeled “TH” & “TPTH”. Connect the wires to the gas valve as labeled. (TH to TH and TPTH to TPTH). Additionally there is a connector labeled “Motor”. Connect this “Motor” connector to the stepper motor on the gas valve (if present). Route Wiring Harness 1001-P904SI Under Fan Inside Fireplace.
IPI Electronic Ignition System Overview The IPI system is an advanced burner controller that provides you with the option of having either a StandingPilot, or an intermittent igniting system. This alternating mode is controlled by the CPI/IPI Switch (Continuous Pilot Ignition/Intermittent Pilot Ignition) located on the IPI System Box.
IPI Electronic Ignition System the receiver and then press the power button [5] on the transmitter. An audible beep will sound to indicate the system is programmed and ready to be used. NOTE: The Remote Receiver module can also be located outside of the appliance to a maximum of 6ft away installed in a certified deep wall switch electrical box (2-3/4” depth). For this configuration an extension wiring harness (P/N: 1001-P904SI) is required.
IPI Electronic Ignition System Configuration #1: Basic manual HI/LO and manual ON/OFF capabilities. Receiver Module 0.584.523/521/221 1001-P221SI Configuration #2: Remote ON/OFF and manual HI/LO capabilities. OPTIONAL: For units with remote HI/LO capabilities, a modulating servo is required to be installed on the valve. The connectors to this servo must be connected to the Remote Harness as shown in the figure above.
Electronic Ignition Lighting Instructions If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. Always light the pilot whether for the first time or if the gas supply has ran out with the glass door opened or removed. FOR YOUR SAFETY READ BEFORE LIGHTING: A. This fireplace is equipped with an ignition device which automatically lights the pilot. Do NOT try to light by hand. B.
IDV26 LOGF26 10 1 2 9 B A 3 C D 4 8 6 5 7 2 1 4 3 A D C B 7 6 5 10 8 8 9 WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this appliance may result in property damage or personal injury.
IDV26 LOGF27 6 B 1 C D A 3 5 2 4 1 2 A B C D 3 6 4 5 4 WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this appliance may result in property damage or personal injury.
Log Placement – LOGF35 LOGF35 Log Set and Glowing Embers Parts List This illustration shows the rear log positioning bracket and 4 pin locating positions. Log A has 2 locating holes. Position those 2 holes over the 2 pins on the left side of the log mounting pan as shown in the picture above. Log B has 2 locating holes. Position those 2 holes over the 2 pins on the right side of the log mounting pan as shown in the picture above. Log C has to be lowered into position just behind Logs A and B.
Log Placement – LOGF36 LOGF36 Log Set includes Glowing Embers, Lava Rock, and Vermiculite. Place Log #1 onto rear log holder and center. Place Log #2 onto left side of Log #1. Place Log #3 onto right side of Log #1. Locate 2 holes on bottoms of Logs #4 and #5, and position onto mounting pins. Locate 1 hole on the bottom of Log #6 and place it onto pin of Log #2. Locate 2 holes on the bottom of Log #7 and place onto the pins of Log #5. Place Glow Ember Kit onto front burner tube and ember plates.
MQRSP4 / MQRSP8 Rock and Glass Support Platform Installation IDV26 / IDV33 / IDV36 Base Unit (As Shipped) Preparation: Remove Grate Bar and replace screws. Remove Ember Plates. Do not remove existing Pilot Shield. Installation: Place MQRSP4 or MQRSP8 over burner. One screw from the Fan Access Cover Plate is all that is required to mount the RSP4.
RSP10 Glass Support Platform -Installation IDV26 / IDV33 / IDV36 Base Unit (As Shipped) Preparation: Remove Grate Bar and replace screws. Remove Ember Plates. Do not remove existing Pilot Shield. Installation: Install RSP10 by placing over burner. Use existing screws at front of firebox bottom to attach Glass Retainer.
MQROCK2 / MQROCK3 -MQRSP4 IDV26 / IDV33 / IDV36 MQRSP4 Parts List 1Ea Rock Support 1Ea Ember Plates Assembly Remove the ember plates and the grate bar by removing the 2 left and right screws on the grate bar. Reinstall screws after removing parts. Place the MQRSP4 Rock Platform and ember plates into place as shown in the illustration above. Step 1: Place Rocks #4 into position as shown. Be sure not to place them directly over top of the burner tube.
MQROCK2/ MQROCK3 -MQRSP4 for IDV26 / IDV33 / IDV36 (continued) Step 4: Place Rocks #6 into position as shown above. Step 5: Place Rocks #3 into position as shown above. Step 6: Place Rocks #1 into position as shown above. Step 7: Place Rocks #3 and #4 into position as shown above. Finished Rock Set and Burn NOTE: If flame impingement on the rocks causes sooting then you may have to move, or remove, one or more rocks. DO NOT PLACE ROCKS DIRECTLY OVER TOP OF THE BURNER TUBE.
MQStone MQRSP8 IDV26 / IDV33 / IDV36 Decorative Stone Set. Supplied for MQRSP8 only. Begin by placing larger stones inside burner tube area. Place smaller stones around outside of burner tube. Cover back and center of burner tube with assorted stones. Add smaller stones to center. Pilot Area MUST be visible at ALL times. Do Not stack or overlay when placing on Burner Tube. NOT ALL STONES WILL BE REQUIRED TO FILL TRAY. Spread glass or Lava Rock (supplied with unit) around firebox bottom.
Glass Ember / MQ Ember Installation -MQRSP8 / RSP10- IDV26 / IDV33 / IDV36 MQ DEALER ONLY Spread glass or ember chunks onto tray and burner. Ensure that layer of glass embers is not excessively thick as this will affect the flame pattern. See below. Pilot Shield* Must Be Kept Clear. MQRSP8 RSP10 (With Glass Retainer in Place) Note: Do not place all the glass embers onto the tray. Only use what is necessary.
Burner System Maintenance It is recommended to annually inspect and clean the Burner System to prevent malfunction and / or sooting. This operation should be performed by your dealer or a qualified technician. -CAUTIONBefore servicing the burner system ensure that the gas supply is turned OFF and disconnect all electrical connections to the appliance. Allow the appliance to cool to room temperature.
Conversion Kit Instructions – PART A Caution: The gas supply shall be shut off prior to disconnecting the electrical power, before proceeding with the conversion. PLEASE CONFIRM THAT STEP 4 IS UNDERSTOOD BEFORE PROCEEDING WITH CONVERSION. WARNING: This conversion kit shall be installed by a qualified service agency in accordance with the manufacturer's instructions and all applicable codes and requirements of the authority having jurisdiction.
Gas Conversion for Top Convertible Pilot (Series 019065X) – PART B Instructions for converting SIT 190 series pilot burner injection from NG to LPG and from LPG to NG only. This information should be considered as supplemental to the Appliance Manufacturer’s Instructions. WARNING: The installation of this conversion kit must only be undertaken by a qualified and certified gas appliance installer. 1. Shut off the gas supply to the appliance. 2. Allow the pilot burner to cool to room temperature.
Gas Conversion for Modulator – PART C -WARNING!- -WARNING!- 67
Troubleshooting the Gas Control System WARNING BEFORE DOING ANY GAS CONTROL SERVICE WORK, REMOVE THE GLASS FRONT. Before troubleshooting the gas control system, be sure external gas shut off is in the "On" position. Problem Spark igniter will not light. Possible Causes Corrective Action Defective or misaligned electrode at pilot. Check for spark at electrode and pilot: if no spark and electrode wire is properly connected, replace igniter. Defective igniter (pushbutton). Using a match, light pilot.
IDV26 Parts List Part No.
VI30GBL Grill Kit – Black Fireplace Accessories for IDV33 (Both Front Kits) Door Frame Overlays Z33ADDX Arch Door Frame – Deluxe Black (352) Z33ADTH Arch Door Frame – Top Half Black (353T) Designer Doors for IDV33 Z33DDA1BL Designer Door Arch – Series 1 – Black Z33DDS1BL Designer Door Straight – Series 1 – Black Z33CSS Child Safety Screen - 33" DV Fireplaces Brick and Porcelain Liners IDV33RL Brick Liner IDV33PL Porcelain Liner (Generation 1) IDV33PRL Porcelain Liner (Generation 2) Conversion Kits for
Parts for IDV26/ IDV33/ IDV36 Part No.
This Limited Lifetime Warranty applies only while the unit remains at the site of the original installation and only if the unit is installed inside the continental United States, Alaska, Hawaii, and Canada. The warranty applies only if the unit is installed and operated in accordance with the printed instructions and in compliance with applicable installation and building codes and good trade practices.
