2D Wireless Barcode Reader Quick Guide 2D Wireless Barcode Reader Quick Guide (Rev1) P/N: 8013-0056000
FCC WARNING STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
OUT OF THE BOX INTRODUCTION Micro USB port (w/ Protective Cover) LED Indicator 2D 1 Wireless Barcode Reader 2 Quick Guide (1) iOS Hotkey Button (2) Delete Button 1 2D Wireless Barcode Reader Quick Guide USB Charger Cable -3- Neck Strap Trigger Button Exit Window SPECIFICATIONS Light source Scan rate Sensor Resolution PCS Housing Profile Battery Life Charge Time Coverage 625nm red LED 60 frames/sec 752 x 480 CMOS sensor 5mil/ 1D barcode; 6.
BEEPER INDICATION GETTING STARTED Single long beep Single beep Single short beep Two beeps To scan a barcode, make sure the aiming spot is pointed directly at the barcode scanned. Two short beeps Four beeps (Hi-Lo-Hi-Lo) Five beeps Three beeps Three short beeps CHARGING THE BATTERY Host Scanner Several short beeps USB A Micro USB 1. Flip open the micro USB port on the scanner. 2.
INTERFACE INTERFACE There are 5 interfaces for data transmission/collection: . E043$ *.E043$* *.E042$* BT HID . E042$ BT SPP . C035$ *.c035$* *.c008$* *.C006$* Memory Mode . C008$ USB HID 1. BT HID - Emulates a Bluetooth HID keyboard that transmits each barcode data to the host after decode. (See page 9) 2. BT SPP - Emulates a Bluetooth SPP device that transmits each barcode data to the host after decode. (See page 9) 3.
GETTING CONNECTED PINCODE SETUP There are two modes of wireless communication: . E043$ *.E043$* [ Recommanded ] BT mode - HID 1. Press the trigger for 1 second to activate the scanner. 2. Scan [DISCONNECT] 3. Scan [BT mode - HID]; the scanner will emit several beeps. 4. Select “Wireless Scanner” from discovered device list. 5. If the Bluetooth application requests to enter pincode, please refer to PINCODE SETUP section on the next page. 6. The scanner will beep twice to verify the connection. .
NUMERIC BARCODES *.31* *.32* *.33* *.34* *.35* - 11 - 1 6 2 7 3 8 4 9 5 0 *.36* *.37* *.38* *.39* *.
SMARTPHONE/TABLET CONNECTION Getting Connected - iOS & Android SMARTPHONE/TABLET TOUCH KEYBOARD Touch Keyboard - iOS iOS Hotkey Button 1. Press the trigger for 1 second to power up the scanner. 2. Scan below configuration barcode to clear last pairing record. . E031$ *.E031$* Disconnect 3. Scan below configuration barcode; the scanner will emit several beeps. . E043$ *.E043$* To toggle iOS Touch Keyboard, please press this button.
POWER OFF TIMEOUT BINARY CHECK CHARACTER The timeout of inactivity before auto power-off. Variable Timeout . E029$ ENABLE . B030$ *.B030$* *.B029$* SET MINUTE (Range: 00 ~ 60) . B029$ SET SECOND (Range: 00 ~ 60) The default timeout is 3 minutes 0 second. For example, to set the timeout as 5 minutes 30 seconds: 1. Scan [Set Minute] 2. Scan [0] & [5] on page 11 & 12. 3. Scan [Set Minute] 4. Scan [Set Second] 5. Scan [3] & [0] on page 11 & 12. 6. Scan [Set Second] .
GENERAL SETTINGS READING MODE . A001$ . F002$ DEFAULT TRIGGER . P023$ . F005$ ABORT CONTINUOUS CHECK VERSION CONTINUOUS AUTO OFF . A007$ . F006$ BEEPER *.F006$* VIBRATOR . F012$ . D035$ BEEP OFF VIBRATOR OFF . F018$ *.D035$* *.D034$* .
KEYBOARD LAYOUT . C009$ . C010$ ENGLISH (USA) JAPAN (106 key) ENGLISH (UK) CANADIAN (FRENCH) FRENCH CANADIAN (TRADITIONAL) . C018$ . C025$ . C034$ . C012$ . C029$ . C011$ GERMAN NORWEGIAN . C026$ . C014$ ITALIAN SWEDISH . C031$ .
KEYBOARD LAYOUT . C030$ . C017$ CZECH (QWERTY) BELGIAN (AZERTY) . C028$ . C022$ CZECH (QWERTZ) DUTCH . C027$ . C021$ HUNGARIAN (QWERTZ) DANISH . C032$ . C024$ HUNGARIAN (101 KEY) SLOVAK SWISS (GERMAN) BRAZILIAN (PORTUGUESE) . C033$ . C016$ . C023$ .
ENABLE SYMBOLOGIES . N017$ . A002$ ENABLE ALL CODE IATA . N010$ . L010$ UK PLESSEY GS1 DATABAR . G021$ . L001$ MSI PDF417 *.G021$* *.G025$* *.G027$* *.G031$* . G025$ . N001$ INDUSTRIAL 2 OF 5 QR CODE MATRIX 2 OF 5 MICRO QR CODE . G027$ . M010$ . G031$ .
MEMORY MODE TERMINATOR . D012$ . C035$ CR . D011$ LF . D013$ CR + LF *.c035$* Memory Mode After scanning the above barcode, the scanner will be able to collect barcode data off-line. The barcode data will be stored in the format of: < Date >, < Time >, < Barcode Data > < CR > To retrieve stored data, please connect the scanner to the host with cable, access removable storage device “MiniScan” from which you may open or copy the file “BARCODE.txt” to your computer.
MEMORY MODE MEMORY MODE . R011$ . R006$ *.R006$* Example: To set Date to 2014-08-01 (Year-Month-Day): 1. Scan [Set Date] 2. Scan [1], [4], [0], [8], [0], [1] on page 11 & 12. 3. Scan [Set Date] . R007$ *.R007$* DATA FORMAT SET DATE SET TIME Example: To set Time to 08:10:30 am (Hr:Min:Sec) 1. Scan [Set Time] 2. Scan [0], [8], [1], [0], [3], [0] on page 11 & 12. 3. Scan [Set Time] *.
MEMORY MODE MEMORY MODE . R008$ *.R008$* . R009$ DATE FORMAT TIME FORMAT *.
QR Code PDF417 DataMatrix - 31 - - 32 -
