MT7937B Wireless Barcode Scanner Quick Guide Full user’s manual is available on the enclosed CD. Version 1.
FCC WARNING STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
FCC Caution: 1. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. 2. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. 3.
OUT OF THE BOX INTRODUCTION 1. LED Indicator Wireless Scanner Tools 2. Exit Window Wireless Barcode Reader 3. Hard Reset Button CD (insert pin into the hole) 4. Trigger NUMERIC BARCODES MT7937B Wireless Barcode Reader Quick Guide Quick Guide Hand Strap *1* *2* *3* *4* *5* 1 2 3 4 5 Quick Connection Card USB Charger Cable -3- 5.
BEEPER INDICATION GETTING STARTED To scan a barcode, make sure the aiming beam crosses every bar and space of the barcode. CHARGING THE BATTERY Host USB A Scanner Micro USB 1. Flip open the micro USB port on the scanner. 2. Insert the micro USB connector into the port on the scanner and USB A connector into a USB port on the host PC.
GETTING CONNECTED PINCODE SETUP There are two modes of wireless communication: . E043$ *.E043$* BT - HID 1. Press the trigger for 1 second to activate the scanner. 2. Scan [DISCONNECT] 3. Scan [BT-HID]; the scanner will emit several short beeps. 4. Select “Wireless Scanner” from discovered device list. 5. The wireless application may prompt you to scan a pincode(see PINCODE SETUP section) it generated. 6. The scanner will beep twice to verify the connection. . E042$ *.E042$* BT - SPP 1.
NUMERIC BARCODES *1* *2* *3* *4* *5* -9- 1 6 2 7 3 8 4 9 5 0 *6* *7* *8* *9* *0* - 10 -
POWER OFF TIMEOUT The timeout of inactivity before auto power-off. Variable Timeout Simply follow instruction in [BT - HID] (page 7) ,in which step 5 can be skipped since iOS & Android will not require pin-code for connection. . B030$ *.B030$* *.B029$* SET MINUTE (Range: 00 ~ 60) . B029$ SET SECOND (Range: 00 ~ 60) The default timeout is 3 minutes 0 second. For example, to set the timeout as 5 minutes 30 seconds: 1. Scan [Set Minute] 2. Scan [0] & [5] on page 9 & 10. 3. Scan [Set Minute] 4.
GENERAL SETTINGS READING MODE . A001$ . F002$ DEFAULT TRIGGER . P023$ . F003$ ABORT TOGGLE . A007$ CHECK VERSION BEEPER . F001$ FLASH . F005$ CONTINUOUS . F012$ BEEP OFF . F018$ BEEP ON - 13 - .
KEYBOARD LAYOUT . C010$ ENGLISH (USA) JAPAN (106 key) ENGLISH (UK) CANADIAN (FRENCH) . C018$ . C009$ . C025$ . C034$ . C012$ FRENCH CANADIAN (TRADITIONAL) . C029$ . C011$ GERMAN NORWEGIAN . C026$ . C014$ ITALIAN SWEDISH . C031$ .
KEYBOARD LAYOUT . C017$ CZECH (QWERTY) BELGIAN (AZERTY) . C030$ . C028$ . C022$ CZECH (QWERTZ) DUTCH . C027$ . C021$ HUNGARIAN (QWERTZ) DANISH . C032$ . C024$ HUNGARIAN (101 KEY) SLOVAK SWISS (GERMAN) BRAZILIAN (PORTUGUESE) . C033$ . C016$ . C023$ SWISS (FRENCH) - 17 - .
ENABLE SYMBOLOGIES . G010$ . A002$ ENABLE ALL CODE CODE 93 . N017$ . K010$ CODE 32 IATA . L014$ . L010$ UK PLESSEY TELEPEN . L001$ . N032$ MSI GS1 DATABAR INDUSTRIAL 2 OF 5 GS1 DATABAR LIMITED MATRIX 2 OF 5 GS1 DATABAR EXPANDED . N010$ . N001$ . M010$ - 19 - .
TERMINATOR TEST BARCODES . D012$ CR . D011$ Code 39 CODE-39 TEST LF Interleaved 2 of 5 . D013$ CR + LF 9876543210 Code 128 . D010$ NONE 12345678 . D015$ SPACE EAN .
