Instructions / Assembly

2 Commerce Drive, Cranford, NJ 07016 www.nationaltree.com
SAVE THESE INSTRUCTIONS
CAUTION: IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
• Do not use seasonal products outdoors unless
marked suitable for indoor and outdoor use.
When products are used in outdoor applications,
connect the product to a Ground Fault Circuit
Interrupter (GFCI) outlet. If one is not provided,
contact a qualified electrician for proper installation.
• This seasonal use product is not intended for
permanent installation or use.
• Do not mount or place near gas or electric
heaters, fireplaces, candles or other similar
sources of heat.
• Do not secure the wiring of the product with
staples or nails, or place on sharp hooks or nails.
• Unplug the product when leaving the house, when
retiring for the night, or if left unattended.
• Do not let lamps rest on the supply cord or any wire.
• CAUTION: This is an electrical product – not a toy!
To avoid risk of fire, burns, personal injury and
electric shock, it should not be played with or
placed where small children can reach it.
• Do not use this product for other than its intended use.
• Do not hang ornaments or other objects from
cord, wire or light string.
• Do not close doors or windows on the product or
extension cords as this may damage the wire
insulation.
• Never operate this product if the power cord or
plug is damaged.
• Use only manufacturer specified replacement bulbs.
• Read and follow all instructions that are on the
product or provided with the product.
USE AND CARE INSTRUCTIONS
• When storing the product, carefully remove the
product from wherever it is placed, avoiding any
undue strain or stress on the product conductors,
connections, and wires.
• When not in use, store neatly in a cool, dry
location protected from sunlight.
Shaping
The product is shipped from the factory with the branch tips compressed to the center.
Each branch tip must be shaped to its proper position to give the product a natural look.
This will also bring the piece to its advertised dimension. The care and attention given to
this final process will result in a genuinely beautiful and appealing holiday decoration.
Shaping is done by gently grasping the branch tips and spreading them out away
from the center. The BEFORE photo shows the product as it appears out of the box.
The AFTER photo shows how the product should look after proper shaping.
Dual Color
®
Operating Instructions (if equipped)
The foot switch operates the functions of the lights. There are 9 functions, each one is
activated with the press of the foot switch. Functions occur in the following order:
Steady warm white; steady multicolor; steady pastel; warm white fading to multicolor;
fading warm white; Fading multicolor; flashing warm white; flashing multicolor; flashing
warm white to multicolor. Light functions always follow this sequence.
BEFORE AFTER
BEFORE AFTER
Note: All products will need some amount of branch shaping before final display.
These products include small trees, porch bushes, teardrops, centerpieces and
similar items. Wreath and garland images are used below to illustrate this point.
Bulb Replacement
1. Unplug light string from power source.
2. Pull up on the Base Lock™ unlatching
the bulb from the bulb
socket. Gently pull the bulb
straight out (Figure 1).
3. Before inserting the new bulb
into socket, make sure that
the two wires on either side
of the the bulb base are straight up and
flush with the base (diagram at right).
4. Carefully insert new bulb into socket
and push down Base Lock until it snaps
into place (Figure 2).
LED Bulbs (Figure 3)
1. Unplug light string from power
source.
2. Pull up on the Base Lock™ unlatch-
ing the bulb from the bulb socket.
Gently pull the bulb straight out.
3. Carefully insert new bulb into socket
(bulb is keyed and only goes in one
way) and push down Base Lock until
it snaps into place.
NOTE: Fuse failure is sometimes a
reason for non-functioning light
strings. The fuses are found in the light
string plug. If one is burnt out, replace
it with a spare fuse included in the
accessories bag.
Fuse Replacement
1. Unplug light string from power source.
2. Slide the fuse access cover away from
cord side (in direction of arrow, Figure
4) exposing fuses.
3. Remove fuses from compartment and
examine. Replace burnt out fuse with
new one.
4. Close fuse compartment by sliding
access cover back in towards cord side
of plug (Figure 5).
Fig. 1
Fig. 2
Fig. 4
Fig. 5
Fig. 3
Pre-Lit Products
US 3-18