Instructions / Assembly

Fig 3
ASSEMBLY OF THE TREE
1. Locate the bottom section of the tree which is identified
by a label on the outer branches marked “A” (Fig 5).
2. Remove the protective plastic cap by twisting and pulling
it from the end of the pole, (that is pinched to a point), and
place the end into the tree stand. Be sure the pointed end
of the pole extends to the bottom end of the stand.
3. Now tighten the eyebolts evenly on the tree stand; being
careful not to over-tighten (Fig 3).
ASSEMBLY OF THE TREE STAND
1. Remove the tree stand from the plastic bag, loosen the eye
bolt and open the tree stand to form an “X”.
2. Align the holes for the insertion of the remaining (2)
eyebolts.
3. Insert each eyebolt and begin threading in a clockwise
direction for a couple of rotations only; leaving enough
room for the tree’s pole from section “A” to be inserted into
the assembled stand (Fig 2).
4. Place the tree stand in its desired location; as once the tree is
fully assembled, it may be too difficult to move and relocate.
Fig 2
10. Once section “B” is fully inserted downward into section “A”;
both section “A” and section “B” will now be lit.
11. Again, carefully cut the nylon strapping bounding the
branches upright; being extremely careful not to cut any of
the exposed light set wires.
12. Now gently guide the branches of section “B” downward
into place.
13. Depending on the height of the tree you have purchased,
you will continue to build your tree upwards, section by
section, following the above steps until the tree is
completely assembled. Each section of the tree is labeled in
alphabetical order beginning from the bottom to the top.
8. Locate the next section of the tree which is identified by a
label on the outer branches marked “B” (Fig 5).
9. Remove the protective plastic cap by twisting and pulling it
from the end of the pole on section “B”; insert that end onto
the top of the pole of section “A” (Fig 4).
Fig 4
EZ-POWER™ TECHNOLOGY
NOTE: Your tree has been designed with EZ-Power™
technology; allowing for each of the tree’s remaining
sections to light up automatically, upon a firm insertion of
each lettered section (Fig 5).
CCT17
Fig 1
A
B
C
Foot Pedal
Fig 5
Fig 6
4. Carefully cut the nylon strapping bounding the branches
upright.
CAUTION: Be extremely careful not to cut any of the exposed
light set wires.
5. Now gently guide the branches downward into place.
6. Beneath the canopy of section “A”, contains an push button
foot pedal with cord and plug (Fig 6).
Remove the twist-tie binding the cord together and insert
the plug into a working electrical outlet.
7. 8 function push button foot pedal operation:
The 8 function push button foot pedal is intended to provide
8 function lighting capability.
ASSEMBLY INSTRUCTIONS
(We recommend wearing proper clothing in order to prevent
scratches that may occur during the assembly process.)
Carefully unpack the contents from the tree’s carton (Fig 1);
including the contents of the poly-bag that is adhered to the
interior flap of the tree’s carton.
Your tree should include the following components:
A folding metal tree stand with (3) eyebolts.
A 8 function push button foot pedal with cord and plug (Fig 6);
which is pre-attached at the lowest section of your tree (Fig 5).
The 7.5’ trees will have (3) tree sections; (“A”, “B” and “C”; as
shown in Fig 5).
FOOT PEDAL OPERATION
Note: Your Pre-lit Christmas tree’s functions and built in timer are
controlled by the attached foot pedal. Simply press the Foot
Pedal to cycle through the following functions:
• Demo
• Steady On
• Slow Sequential
• Fast Sequential
• Slow SLO GLO
• Fast SLO GLO
• Slow Fade
• Fast Fade
• Off
1. Gently remove the plug from its electrical outlet, and carefully bind
the cord which contains the push button foot pedal and plug.
2. Beginning with the tree’s top section; lift each section straight
up from the section below, and continue working downward.
NOTE: You may have to slightly wiggle each section as you lift
each section upward.
3. To remove the bottom and final section; loosen the eyebolts by
turning in a counter-clockwise direction and lift section “A”
from the support collar of the tree stand.
4. Gently fold the branches of each section upward, towards the
center, and position in the storage container.
NOTE: With the exception of the tree’s “top” section; by holding
each section upside down; the branches will collapse
downward, due to the hinging, aiding in the packing of each
section into the storage container.
5. Fully unthread the eyebolts from the tree’s stand and fold
together; placing in the storage container.
6. It is recommended to always store the tree in a cool, dry
location protected from excessive exposure to heat or sunlight.
DISASSEMBLY & STORAGE
NOTE: ALTHOUGH THE LED/RGB LIGHT STRINGS ON THE TREE
ARE RATED FOR INDOOR OR OUTDOOR USE; THE COMBINATION
OF THE TREE WITH THE LED LIGHTS IS FOR INDOOR USE ONLY.
NOTE: DO NOT USE ANY ADDITIONAL LIGHTING OR
ORNAMENTATION THAT IS POWERED THROUGH THE LIGHT
BULB SOCKETS. DOING THIS MAY RESULT IN DAMAGE TO THE
LIGHTING SYSTEM OR MAY CAUSE PERSONAL INJURY;
THEREFORE VOIDING THE LIMITED WARRANTY PROVIDED
WITH THIS PRODUCT.
TROUBLESHOOTING
NOTE: The tree’s 8 function lighting capability is controlled solely
by the use of the foot pedal provided.
1. If failure to light, press the push button foot pedal; as it may be in
the “Off” mode.
2. If the top of the tree or another individual lettered section does
not illuminate, remove each section and then reinsert as
instructed, to ensure the electrical connection is made.
NOTE: The tree’s top is designed specifically for a secure and firm
connection point. Downward force will be needed to ensure that
the electrical connection occurs.
TIMER FEATURE:
Timer is 6 hours on 18 hours off.
TIMER MODE:
Your 8 Function tree is equipped with a built-in timer. The timer is
activated when the foot pedal is pressed straight down and held
for 5 seconds. The lights will flash three times to indicate that the
timer is on. To turn off the timer press the foot pedal straight
down and hold for 5 seconds. The tree lights will flash once
indicating that the timer is off.
Model No. RL75169-RPHO2
Made in China
Printed in China
This is not a toy, for decorative use only.
DISTRIBUTED BY HOME DEPOT U.S.A., INC. 2455
PACES FERRY RD., N.W. Atlanta, GA 30339 All rights reserved.
This product was pre-tested before shipment and date
coded. In keeping with the National Electric Code, this
product is intended for seasonal (90 days max.) installation
and use. For problems or questions on this product call our
customer service toll-free at 1-877-527-0313.
18”
2017 Home Depot.com
7.5ft Emperor Fir Instruction Sheet - 8 Function Foot Pedal (English)
Date: 9/15/17
15”
Item #RL75169-RPHO2