The Everyday System™ 8FT HANGING & 6 DRAWER CABINET (14’’ Deep) Congratulations on your purchase of the The Everyday System. Installing your system is straightforward if you follow our instructions in the order provided. Remember – measure twice, drill once! Front View Vista frontal Vue frontale Felicitaciones por su compra de The Everyday System. La instalación de su sistema es sencilla si sigue nuestras instrucciones en el orden indicado. Recuerde: ¡Mida dos veces, perfore una vez! 96.75” 83.
(EN) Order of Installation Rules and Warnings: Please follow the instructions in this order for optimum results and stability of your Everyday System. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Prepare your space Uprights Shelf Brackets Standard Shelf Long Shelf Shoe Shelf Drawer Cabinet Bin Cabinet Mesh Door Cabinet Media Cabinet Desk Unit Closet Rod (EN) • THIS IS NOT A FREE-STANDING UNIT. FOR SAFETY, ALWAYS ANCHOR TO THE WALL. • Do not attempt to assemble without FIRST securing Upright to the wall.
Boxes Included Qty Description 2 Drawer Pull 3pcs/box 1 Closet Rods with Mount 24 inch 1 Closet Rods with Mount 2pcs/box 24 inch 2 Uprights 87.25 x 14 inch 1 Uprights 3pcs/box 87.25 x 14 inch 2 Basic Shelf Woodgrain 24 x 14 inch 4 Basic Shelf Woodgrain 3pcs/box 24 x 14 inch 2 3 Drawer Cabinet Woodgrain 24 x 14 inch 6 Shelf Bracket Set 3pcs/box 14 inch 21 Total Number of boxes 3 INS-0066 (Rev.
Included Parts | Piezas incluidas | Pièces contenues dans l’emballage Note: Box may include more than one upright and hardware set. Nota: La caja puede incluir más de un conjunto de montante y accesorios. Note: Le carton peut contenir plusieurs montants et plusieurs lot d’articles de visserie.
(EN) Before you start your build do not forget to prepare your space! Step 1: Tear out any unwanted structures (Example: previous wire closet) Step 2: Repair any holes or damaged areas by patching and painting. Step 3: Verify your measurements and confirm the installation will fit. Examples: Step 3a: If between two walls, measure baseboard to baseboard. 2 Step 3b: Be aware of obstructions around the space such as wall lights, hanging lights, outlets, switches, etc.
(EN) Find the high spot in the floor. Option 1: Use a long level and move along perimeter of the floor noting where the highest point is. This is the high spot in the floor. (1a) System height Altura del sistema Hauteur du rangement 1c Option 2: Step 1 - Draw a light line on the wall that can be erased later. Step 2 - Find the shortest distance between the floor and the line. This is the high spot in the floor. Measure 87-1/4” from the high point (1b) and make a light mark (1c).
(EN) For steps 2-5, use your Layout Design to locate your Upright positions on your wall. Helpful Hints: - Always make sure the top of the template aligns with your System Height. - Always make sure the template is level before marking hole locations. - Use painters tape to hold the Wall Template in place while you mark hole location. (ES) Para los pasos del 2 al 5, use el diseño de la disposición para ubicar la posición del montante en su pared.
3 3 (EN) Depending on your Layout Design you will be using either the 16”, 24”, 30” or 48” holes for this span. Mark the two holes for each appropriate Upright location. (ES) Dependiendo del diseño de la disposición, usará los agujeros separados 16”, 24”, 30” o 48” para establecer esta distancia. Marque los dos orificios para la ubicación de cada montante.
6 6 (EN) WARNING: This wall bracket mount installation is specific to drywall with studs. If your wall is of different construction, you must find appropriate means to attach the wall bracket. It is not required to have the upright brackets be tied into a stud as drywall is acceptable. (ES) ADVERTENCIA: Esta instalación para el montaje de los soportes de pared es específica para paredes de yeso con bastidor.
7 7 8 (EN) Install leveler all the way into Uprights. (ES) Inserte el nivelador por completo en los montantes. (FR) Insérez la vis de calage à fond sur les montants. (EN) Place Upright on bracket (8a), and partially install screws to secure (8b). Do not tighten. (ES) Coloque el montante en el soporte (9a), e instale parcialmente los tornillos para asegurarlo (8b). No los ajuste. (FR) Fixez le montant au support (9a) et insérez partiellement les vis pour maintenir le en place (8b). Ne serrez pas.
9 9 (EN) Adjust leveler leg to level Upright. Then make sure the back leveler also touches the ground. Ensure Uprights are level to adjacent Uprights. (ES) Ajuste el nivelador delantero para nivelar el montante. Después asegúrese de que el nivelador posterior también toque el suelo. Asegúrese de que los montantes estén al mismo nivel que los montantes adyacentes. (FR) Réglez la vis de calage pour mettre le montant de niveau. Puis assurez-vous que la vis de calage arrière touche le sol.
Included Parts | Piezas incluidas | Pièces contenues dans l’emballage 1 BRACKET Installation Manual SOPORTE Manual de Instalación 2x SUPPORT Manuel d’installation 1x 1x 2x 2x (EN) • THIS IS NOT A FREE-STANDING UNIT. FOR SAFETY, ALWAYS ANCHOR TO THE WALL. • Do not attempt to assemble without FIRST securing Upright to the wall. • NEVER allow children to stand, climb, or hang on drawers, doors, or shelves. (ES) • ESTA UNIDAD NO ES INDEPENDIENTE.
1 2 Do not install hole plug if bracket is used with a pole. No instale el tapaagujero si se usa con un poste. N’installez pas de cache-trou si le support est utilisé avec une perche. 2 INS-0012 (Rev.
3 3.1) 3.2) Do not install cover if bracket is used with drawer. No instale la cubierta si se usa con un cajón. If cover is accidentally installed, pry cover with screwdriver. N'installez pas de couvercle si le support est utilisé avec un tiroir. Si se instala accidentalmente la cubierta, sáquela haciendo palanca con un destornillador. Si vous installez un couvercle par erreur, arrachez-le avec un tournevis. 3 INS-0012 (Rev.
4 4 INS-0012 (Rev.
5 2x 5 INS-0012 (Rev.
Included Parts | Piezas incluidas | Pièces contenues dans l’emballage 1 SHELF Installation Manual REPISA Manual de Instalación ÉTAGÈRE 1x Manuel d’installation 2 2x (EN) • THIS IS NOT A FREE-STANDING UNIT. FOR SAFETY, ALWAYS ANCHOR TO THE WALL. • Do not attempt to assemble without FIRST securing Upright to the wall. • NEVER allow children to stand, climb, or hang on drawers, doors, or shelves. 1x 1x (ES) • ESTA UNIDAD NO ES INDEPENDIENTE.
1 2 Do not install hole plug if bracket is used with a pole. No instale el tapaagujero si se usa con un poste. N’installez pas de cache-trou si le support est utilisé avec une perche. 2 INS-0013 (Rev.
3 3.1) 3.2) If cover is accidentally installed, pry cover with screwdriver. Si se instala accidentalmente la cubierta, sáquela haciendo palanca con un destornillador. Si vous installez un couvercle par erreur, arrachez-le avec un tournevis. 3 INS-0013 (Rev.
4 4 INS-0013 (Rev.
5 2x 6 5 INS-0013 (Rev.
Included Parts | Piezas incluidas | Pièces contenues dans l’emballage 1 CABINET WITH 3 DRAWERS Installation Manual GABINETE CON 3 CAJONES 3x 2x Manual de Instalación PLACARD À 3 TIROIRS 3x 3x Manuel d’installation 3x 3x 3x 1x 3x (EN) • THIS IS NOT A FREE-STANDING UNIT. FOR SAFETY, ALWAYS ANCHOR TO THE WALL. • Do not attempt to assemble without FIRST securing Upright to the wall. • NEVER allow children to stand, climb, or hang on drawers, doors, or shelves.
1 2 2 4x 4x 2x 3 4x 4 2 INS-0018 (Rev.
5 5 6 4x 4x 3 INS-0018 (Rev.
7 7 4 INS-0018 (Rev.
8 8 4x 5 INS-0018 (Rev.
9 9 10 12x 6 INS-0018 (Rev.
11 12 12 4x 7 4x INS-0018 (Rev.
13 14 15 8 The bracket is optional El soporte es opcionaly Le support est optionnel INS-0018 (Rev.
16 9 INS-0018 (Rev.
Included Parts | Piezas incluidas | Pièces contenues dans l’emballage 1 CLOSET ROD Installation Manual TUBO PARA CLOSET Manual de Instalación 1x BARRE DE PENDERIE Manuel d’installation 2x (EN) • THIS IS NOT A FREE-STANDING UNIT. FOR SAFETY, ALWAYS ANCHOR TO THE WALL. • Do not attempt to assemble without FIRST securing Upright to the wall. • NEVER allow children to stand, climb, or hang on drawers, doors, or shelves. (ES) • ESTA UNIDAD NO ES INDEPENDIENTE.
1 2 2 INS-0023 (Rev.