Instruction Manual

ManualsBrandsMartin Universal Design ManualsFurnitureU-UDS5000WD Drawing Table

4444 Lawton Avenue, Detroit, MI 48208 USA • Tel:(313)895-0700/Fax:(313)895-0709

Email: Custservmud@aol.com • visit us at www.MartinUniversalDesign.com

U-UDS5000WD Drawing Table Assembly Instructions

IMPORTANT

If you have difﬁculty assembling your U-DS5000WD Table

or need customer service assistance.

Please call:

Martin Universal Design, Inc. Customer Service Hot Line at

1-313-895-0700.

If you need additional parts,

it is not necessary to contact your dealer

, our Customer Service Rep. will forward them

to you immediately.

Aug. 08 Revised- RPI

Hardware List

[1] - M4x12mm Screws

(18 each)

[2] - Nuts

(2 each)

[3] - M6x8mm Allen

Screw (4 each)

[4] - M6x12mm Allen

Screw (2 each)

[9] - Hinge

(4 each)

[10] - Wrench

(1 each)

Pg. 1

Additional Tools needed: Phiillips Screwdriver

[11] - Allen-Wrench

(1 each)

[5] - Knobs - Male

(4 each)

[6] - Washer with small

hole (4 each)

[7] - Washer with large

hole (4 each)

[8] - Threaded Rubber

Feet (4 each)

[A] - Table Top (1 each) [B] - Base foot (2 each) [C] - Foot Rest Cross

Support (1 each)

Parts List

[E] - Tilt Bracket End

(2 each)

[F] - Tilt Bracket (2 each) [G] - Pencil Edge

(1 each)

[D] - H-Frame

Support

(1 each)

Summary of content (4 pages)

PAGE 1
U-UDS5000WD Drawing Table Assembly Instructions Additional Tools needed: Phiillips Screwdriver Hardware List [1] - M4x12mm Screws (18 each) [2] - Nuts (2 each) [5] - Knobs - Male (4 each) [6] - Washer with small hole (4 each) [9] - Hinge (4 each) [10] - Wrench (1 each) [3] - M6x8mm Allen Screw (4 each) [7] - Washer with large hole (4 each) [4] - M6x12mm Allen Screw (2 each) [8] - Threaded Rubber Feet (4 each) [11] - Allen-Wrench (1 each) Parts List [B] - Base foot (2 each) [C] - Foot Rest Cross
PAGE 2
U-UDS5000WD Drawing Table Assembly Instructions IMPORTANT: ASSEMBLY IS EASIER AND SAFER WITH TWO PEOPLE STEP 1] Assembly Base of Table Begin by taking the [2] Lower Base Feet (part B) and attach the foot rest (part C) to the Lower Base Feet using [2] M4 x 12mm screws (part 1). Secure by tightening screws. See FIG 1. D 5 Continue by sliding the H-Frame (part D) down into the sides of the Lower Base Feet (part B). Secure with large washer (part 7) and Knob (part 5). Tighten Knob to secure.
PAGE 3
U-UDS5000WD Drawing Table Assembly Instructions IMPORTANT: ASSEMBLY IS EASIER AND SAFER WITH TWO PEOPLE 3 G A 4 6 3 2 6 F E 4 STEP 3] Tilt Bracket Assembly Lay table top onto ﬂat carpeted or cardboard surface with holes facing up (to protect from scratching table top). Attach the Tilt Bracket End (part E) to the table top in the position as shown in FIG 3 using [2] each M6 x 8mm Allen Screws (part 3) per bracket. Line up holes in bracket end with T-nuts in table top. Secure with Allen-Wrench.
PAGE 4
U-UDS5000WD Drawing Table Assembly Instructions IMPORTANT: ASSEMBLY IS EASIER AND SAFER WITH TWO PEOPLE STEP 5] Table Adjustments To Raise or Lower the height of the table, loosen the Lower knobs found on the channeled Base supports. Raise or Lower the table to your desired position and re-tighten the knobs to secure. See illustration below. To Adjust the tilt of your table, loosen the knobs found on the tilt brackets. Loosen and change the tilt of the table top, retighten once desired tilt is achieved.