Magnum Pro 2000 user’s guide
CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 INSTALLING THE MAGNUM PRO 2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 OPERATING VIA THE REMOTE CONTROL UNIT . . . . . . . . . . . . . . . . . . . . . . . . . 5 OPERATING VIA A 0-10 VOLT SOURCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 SLAVE OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLING THE MAGNUM PRO 2000 Your Magnum Pro 2000 package comes complete with the following items: Magnum Pro 2000 smoke machine with remote control unit. 5 metre (16.5 ft) XLR/XLR cable for remote control unit. Adaptor-cap (for fluid tank) with fluid filter. Users guide. IMPORTANT! Before attempting any of the following ensure that the machine is disconnected from any mains power. Fitting the mains plug: The Magnum Pro 2000 is delivered from the factory without a plug on the mains lead.
Fitting/connecting the remote control unit: You will find the remote control unit plugged into the back of the machine and secured by two finger screws. This unit can be removed from the machine and mounted in a rack system or placed on a table. Please follow this procedure to remove the unit: Unscrew the two finger screws and draw out the remote control unit by pulling the finger screws.
Using the auto-timer: This feature allows the machine to produce smoke automatically for a programmable period of time called the duration and then continuously repeat this smoke duration by a programmable cycle. Both duration, cycle and smoke level are stored in the Magnum Pro 2000 memory, not in the remote control unit. Follow the listed example below to get familiar with this feature: Adjust the smoke output potentiometer to medium smoke emission. Press the smoke button for approximately 3 seconds.
SLAVE OPERATION Whether you choose to operate your Magnum Pro 2000 via the remote control unit or via a 0-10 Volt source you will have the possibility of adding on an infinite number of slave machines that will all perform the same as the master machine by using the XLR slave output located on the back of the machine. The first slave machine should have its control input connected to the slave output on the master machine.
The machine indicates heating but the READY LED never comes on. Reset the thermo-switch inside the machine. Please see the section named "Resetting the ThermoSwitch". If the problem persists then consult your Martin dealer. In any other case you should contact qualified service personnel. REPLACING THE FUSE It may occur that the fuse inside the Magnum Pro 2000 blows. If that should happen you will have to replace this fuse. Use a 10 A slow-blow fuse if the machine is a 230 V model.
IMPORTANT! Before attempting any of the following ensure that the machine is disconnected from any mains power and cooled down. 1 Remove the fluid tank from the machine. 2 Remove the two Philips screws that secure the top-cover over the heating element. 3 Slide the cover backwards until the thermo-switch becomes accessible. The thermoswitch is located on the mid, left hand side of the heating element with two wires attached. 4 Press the plastic button on the thermo-switch, thereby resetting this switch.
TECHNICAL SPECIFICATIONS Magnum Pro 2000 Dimensions: See figure 1 Weight (empty tank): 13 Kg (28.5 lb) AC-voltage - 230 V model: AC-voltage - 115 V model: AC-frequency: 200 - 260 V 100 - 130 V 50 / 60 Hz Power consumption: 1700 W Maximum fluid consumption: 0.2 l/min Tank capacity: 9.5 l (2.5 gall) Warm-up time: 8 - 10 min Fuse: Overheat protection: 10 AT at 200 - 260 V 15 AT at 100 - 130 V Electronic / Mechanical (with manual reset) Figure 1: Overall dimensions in mm (inches).