User.
User.fm Page 2 Monday, April 17, 2000 11:22 AM INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 STAND-ALONE OPERATION . . . . . . . . . . . . . . . . . . . . . 7 CONTROLLER OPERATION . . . . . . . . . . . . . . . . . . . . . . 8 DMX PROTOCOL . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 SERVICE . . . . . . . . . . .
User.
User.fm Page 4 Monday, April 17, 2000 11:22 AM SAFETY Warning! 2 This product is for professional use only. It is not for household use. This product presents risks of lethal or severe injury due to fire and heat, electric shock, ultraviolet radiation, lamp explosion, and falls. Read this manual before powering or installing the fixture, follow the safety precautions listed below and observe all warnings in this manual and printed on the fixture.
User.fm Page 5 Monday, April 17, 2000 11:22 AM To protect yourself and other s f rom burns and f ire • Never attempt to bypass the thermostatic switch or fuses. Always replace defective fuses with ones of the specified type and rating. • Keep all combustible materials (for example fabric, wood, paper) at least 0.1 meters (4 inches) away from the fixture. Keep flammable materials well away from the fixture. • Do not illuminate surfaces within 0.3 meters (12 inches) of the fixture.
User.fm Page 6 Monday, April 17, 2000 11:22 AM INSTALLATION 3 The RoboColor Pro 400 package includes mounting bracket and fittings, 3-pin XLR data cable, mains cable, and this users guide. The fixture is adjusted at the factory so that only a few basic procedures are necessary before the fixture is ready for use. Warning! Disconnect the unit from AC power before proceeding. Important! Verify that the voltage and frequency settings match your power supply before connecting to power.
User.fm Page 7 Monday, April 17, 2000 11:22 AM STAND- ALONE OPERATION 4 The RoboColor Pro 400 may be operated in stand-alone mode without a controller. Music-trigger uses a built in microphone for sound-activated control and autotrigger runs at a preset speed using an internal trig source. 1 Use the DIP-switch on the rear panel to select a trigger type. To select musictrigger, set DIP-switch pins 1, 2, and 10 to ON. To select auto-trigger, set DIPswitch pins 2 and 10 to ON. Set all other pins to OFF.
User.fm Page 8 Monday, April 17, 2000 11:22 AM 5 CONTROLLER OPERATION The RoboColor Pro 400 accepts two control protocols: Martin RS-485 and DMX 512. CONNECTING THE SERIAL DATA LINK The RoboColor Pro 400’s XLR connections are configured for Martin protocol controllers, that is, the data sockets are wired with pin 2 to hot (+) and pin 3 to cold (-). When connecting a RoboColor Pro 400 to a DMX device (pin 2 cold and pin 3 hot), you must swap pins 2 and 3 with a phase-reversing cable.
User.fm Page 9 Monday, April 17, 2000 11:22 AM ADDRESS SETTING The DIP-switch on the rear panel is used to select the control address on which the RoboColor Pro 400 responds to the controller. The control address, also known as the start channel, is the first channel used to receive instructions from the controller. For independent control, each fixture must have a unique control address and nonoverlapping control channels. The total number of channels required depends on the operation mode.
User.fm Page 10 Monday, April 17, 2000 11:22 AM ABOUT FAN CONTROL Beginning with CPU firmware version 6.5, fan control is completely automatic. The fan operates as follows: • Fan speed is automatically reduced to 50% after protocol detection and the fan stops 1 minute later if the lamp is still off. • When the lamp is on, the fan runs at the full speed. • Fan speed reduces to 50% when the lamp is turned off and the fan stops completely 1 minute later.
User.
User.
User.fm Page 13 Monday, April 17, 2000 11:22 AM SERVICE 7 This section describes how to adjust the lamp for best performance and how to change the default DMX mode setting. Refer all other service to a Martin technician. Warning! Disconnect the fixture from power before removing any cover. LAMP ADJUSTMENT Fine adjustment of the lamp position may improve performance. The lamp access plate is held in place with 3 thumbscrews. The 3 Phillips screws on the access plate are used to adjust the lamp.
User.fm Page 14 Monday, April 17, 2000 11:22 AM DMX MODE SETUP The DMX mode is selected with a jumper on the main circuit board inside the fixture. The factory default is DMX mode 1. 1 Disconnect the fixture from power. 2 Release the 4 bolts that secure the top cover to the fixture and remove the cover. 3 Locate the PCB at the left side of the fixture. Locate 6-pin connector PL11 please see the label inside the top cover. Place the jumper according to the table on page 11 to enable the desired mode.
User.fm Page 15 Monday, April 17, 2000 11:22 AM SPECIFICATIONS 8 Length incl./excl. bracket ..................................... 306 mm (12.0") / 306 mm (12.0") Width incl./excl. bracket......................................... 337 mm (13.3") / 225 mm (8.9") Height incl./excl. bracket........................................ 282 mm (11.1") / 198 mm (7.8") Weight incl. bracket .............................................................................11.0 kg (24 lb) Power and current consumption .......