user’s manual MARTIN LOGAN The Great American Speaker Company
WARNING! • Refer servicing to a qualified Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 technician. • To prevent fire or shock hazard, do not expose this module to moisture. • Turn amplifier off should any abnormal conditions occur. • Do not drive speaker beyond its rated power. Break In . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Installing On A Wall . . . . . . . . . . . . . . . . . .
x2 x1 3
CONNECTION WARNING! Turn your amplifier off before making or breaking any signal connections! These speakers are designed with easy-to-use push-style binding posts that accept bare wire or pins (fig. 2). Additionally, by removing the rubber inserts, they will accept banana plugs (fig. 3) Assign the same color to the (+) and (–) terminals on both the speaker and the amplifier. Make certain that all connections are tight. Fig. 2 Fig. 3 4 Fig.
Fig. 4 INSTALLATION WARNING! Installation other than that described in the body of this document requires specifdocumentation from MartinLogan. ic BREAK IN Allow approximately 72 hours of break-in at 90 dB (moderate levels) before any critical listening. Note: This speaker is not magnetically shielded and therefore should not be placed directly beside or atop a CRT television. INSTALLING ON A WALL Note: These instructions assume the mounting surface is standard wood frame and sheet rock construction.
Fig. 6A Required hardware (not supplied): • (2) 1.5-inch Phillips sheet metal screws • (2) Sheet rock anchors Required tools (not supplied): • Ruler • Level • Electric drill and 1/4” and 1/8” drill bits • Phillips screwdriver 1 Screw the shoulder bolt into the back and install the rubber bumpers in the location shown (fig. 4). 2 Locate mounting location using a level and the installation template (fig. 5A–5B). Fig. 6B 3 Mark the pilot hole locations. 4 Drill the pilot holes using a 1/8-inch drill bit.
FREQUENTLY ASKED QUESTIONS How do I clean my speakers? Use a dust free cloth (such as a micro fiber cloth) or a soft brush to remove dust from your speakers. Do not spray any kind of cleaning agent on or in close proximity to the drivers.
GENERAL INFORMATION WARRANTY INFORMATION Your speakers are provided with an automatic Limited 90 Day Warranty coverage. You have the option, at no additional charge, to receive a Limited 5 Year Warranty coverage.
SPECIFICATIONS* MARTINLOGAN ELECTRO MOTION FX2 Frequency Response . . . . . . . . . . . . . . . . . . . . . 55–25,000 Hz ± 3 dB Dispersion . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160° (horizontal) x 30° (vertical) Sensitivity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 dB @ 2.83 volts/ meter Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Ohms. Compatible with 4, 6 or 8 Ohm rated amplifiers. Crossover Frequency. . . . . . . . . . . . . . . . . .
DIMENSIONAL DRAWINGS 6,8 po (17,2cm) 6.8” (17.2cm) MARTINLOGAN ELECTROMOTION FX2 14.9” (37.9cm) 14,0 po (35,5cm) 14.0” (35.5cm) 14,9 po (37,9cm) ® The Great American Speaker Company Lawrence, Kansas, USA P/N: 9500067 rev. 2 10 tel 785.749.0133 fax 785.749.5320 ©2013 MartinLogan Ltd. All rights reserved. www.martinlogan.com Rev.
