user’s manual ®
WARNING! • Refer servicing to a qualified technician. • To prevent fire or shock hazard, do not expose this module to moisture. • Turn the amplifier off should any abnormal conditions occur. • Do not drive speaker beyond its rated power. The lightning bolt flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.
Content Check List Your new MartinLogan loudspeaker includes the following items. Should you require assistance, please call our service department at (785) 749-0133.
Connection WARNING! Turn your amplifier off before making or breaking any signal connections! For convenience during installation, Tribute 5XW and Monument 7XW feature binding posts on both the top and bottom of the enclosure. Only one set of connections is necessary. These speakers are designed with easy-to-use pushstyle binding posts that accept bare wire (fig. 1). Fig. 1 Assign the same color to the (+) and (–) terminals on both the speaker and the amplifier. Make sure that all connections are tight.
Choosing a Mounting Location Install the speaker between wall studs. Be careful to avoid electrical wires behind the wall and surfaces. Balancing Bass Output Corner placement of these speakers reinforces their bass output. If you require balanced output across the entire audio spectrum avoid mounting these speakers in a corner. Painting the Speaker Grille IMPORTANT! Before painting, remove the grille from speakers and remove the cloth scrim attached inside the grille.
Installation NOTE: These instructions assume the mounting surface is of standard wood frame and conventional sheetrock construction. If you wish to mount the speakers to another type of material, you should contact a bonded contractor. 2. Hold or pin the template in place and mark cut-out with a pencil. 3. Remove the template and cut out the opening with a drywall knife/saw. NOTE: See your local dealer for new construction pre-install brackets (sold separately). 4.
WARNING! Turn your amplifier off before making or breaking any signal connections! 6 Place the speaker in the hole. Monument 7XW: Orient the speaker’s unmarked midrange driver (the driver without ‘MartinLogan’ printed on it) so that it is the closest to the listener’s ear level at the primary listening position. 7 Use the supplied Torx T20 driver and an electric drill to lock all mounting locks in place. Use a low clutch setting on the drill.
Dimensional Drawings Fig. 3: Icon 3XW 15.98 in. (405.95mm) 8.39 in. (213mm) 0.31 in. (7.8mm) Binding Posts 14.41 in. (366.13mm) 4.11 in. (104.3mm) 9.94 in. (252.6mm) Cutout Dimensions (including tolerance) 8.64 x 14.66 in. (219 x 372mm) Fig. 4: Tribute 5XW 4.09 in. (103.93mm) 10.6 in. (269.2mm) 9.04 in. (229.6mm) 0.31 in. (7.8mm) 29.57 in. (751mm) 31.13 in. (790.82mm) Binding Posts Binding Posts Cutout Dimensions (including tolerance) 9.29 x 29.82 in.
Fig. 5: Monument 7XW 4.11 in. (104.3mm) 10.6 in. (269.2mm) 9.04 in. (229.6mm) 0.31 in. (7.8mm) 45.32 in. (1151mm) 46.86 in. (1190.2mm) Binding Posts Binding Posts Cutout Dimensions (including tolerance) 9.29 x 45.57 in.
Frequently Asked Questions How do I clean my speakers? Use a clean cloth or a soft brush to remove the dust from your speakers. Do not spray any cleaning agents on or near the drivers. What size amplifier should I use? We recommend an amplifier rated within the suitable amplifier range of your speaker. Again, we have no favorites; we use electronics and cables quite interchangeably. We would suggest listening to many brands—and above all else—trust your ears.
Contacting Customer Service MartinLogan customer service is available Monday – Friday between the hours of 8 am – 5 pm (central time) by calling (785) 749-0133 or by emailing service@martinlogan.com. General Information SERIAL NUMBER You can locate the serial number on the back of the speaker and the product carton.
How can you be sure to find a current authorized MartinLogan Dealer? Only dealers found on the following pages are current authorized MartinLogan dealers. Goods purchased from any entity not found on these lists list are not entitled to MartinLogan Limited Warranty coverage: • Authorized Online Dealers https://www.martinlogan.com/locator • Authorized United States Dealers https://www.martinlogan.com/locator • Authorized Canadian Dealers https://www.martinlogan.
Warranty Outside of the United States and Canada This warranty applies only to purchases made from authorized MartinLogan dealers and distributors in the United States and Canada. For warranty terms, conditions, and support elsewhere, please contact the authorized MartinLogan distributor in the country where your purchase was made. Warranty outside the US and Canada is established and provided by authorized MartinLogan distributors around the world.
Specifications* Icon 3XW System Frequency Response . . . . . . . . . . . . . . . 78–25,000 Hz ± 3 dB Tweeter Dispersion (horizontal x vertical) . . . . . 80° x 30° Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 dB @ 2.83 volts/meter Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 ohms. Compatible with 4, 6, or 8 ohm rated amps. Crossover Frequency . . . . . . . . . . . . .
Tribute 5XW Monument 7XW 71–25,000 Hz ± 3 dB 52–25,000 Hz ± 3 dB 80° x 30° 80° x 30° 94 dB @ 2.83 volts/meter 95 dB @ 2.83 volts/meter 4 ohms. Compatible with 4, 6, or 8 ohm rated amps. 4 ohms. Compatible with 4, 6, or 8 ohm rated amps. 2250 Hz 200, 3200 Hz Rotatable tweeter for horizontal or vertical installations Rotatable tweeter for horizontal or vertical installations 1.25 x 2.4” (3.2 x 6.1 cm) Folded Motion XT Obsidian transducer with 4.5 x 2.75” (11.4 x 7 cm) diaphragm. 1.25 x 2.4” (3.
® Lawrence, Kansas, USA tel 785.749.0133 fax 785.749.5320 www.martinlogan.com DuPont™ and Nomex® are trademarks or registered trademarks of E.I. du Pont de Nemours and Company. ©2019 MartinLogan Ltd. All rights reserved.
manuel de l’utilisateur ®
AVERTISSEMENT! • Pour les réparations, faites appel à un technicien compétent. • Pour éviter les risques d’incendie ou de décharge électrique, n’exposez pas ce module aux vapeurs d’eau ni à l’humidité. • Veuillez éteindre l’amplificateur en cas de conditions anormales. • Ne poussez pas l’enceinte au-delà de sa puissance nominale.
Liste de vérification du contenu Vous trouverez les éléments suivants dans la boîte pour votre nouvelle enceinte MartinLogan. Si vous avez besoin d’aide, veuillez appeler notre département de service en composante le 785-749-0133.
Raccordement AVERTISSEMENT! Éteignez l’amplificateur avant de faire des raccordements ou d’interrompre tout raccordement de signal! Pour plus de commodité lors de l’installation, Tribute 5XW et Monument 7XW comportent des bornes de reliure en haut et en bas de l’enceinte. Un seul ensemble de connexions est nécessaire. Ces enceintes sont dotées de bornes de raccordement facile à utiliser de style bouton-poussoir qui acceptent les fils nus (fig. 1). Fig.
améliore le rendement des hautes et des moyennes fréquences Les pièces qui sont « trop amorties » avec du tapis, des rideaux ou d’autres matériaux qui absorbent le son peuvent faire en sorte que votre système sonne mat ou sans vie. D’un autre côté, les pièces peuvent avoir tellement de surfaces dures que le système sonnera comme dans un gymnase Expérimentez en ajoutant ou en enlevant des surfaces molles jusqu’à ce que vous trouviez un mélange qui sonne bien.
Installation REMARQUE : ces instructions supposent que la surface de montage est un cadre en bois standard et une construction en gyproc standard. Si vous souhaitez monter les enceintes sur un autre type de matériel, vous devez communiquer avec un entrepreneur cautionné. REMARQUE : consultez votre revendeur local pour obtenir les nouveaux supports préinstallés (vendus séparément).
8 Utilisez toujours le tweeter Folded Motion XT à la verticale. Si l’installation est horizontale, le tweeter doit pivoter de 90 degrés. Pour ce faire, retirez le déflecteur en aluminium (le cas échéant) et, à l’aide d’un tournevis cruciforme, retirez les quatre vis retenant le tweeter en place. Faites pivoter le tweeter dans le bon sens puis revissez l’ensemble (fig 2). 9 Appuyez délicatement pour remettre le déflecteur en place. 10 Placez la grille magnétique sur l’enceinte. Fig.
Plans Dimensionnels Fig. 3 : Icon 3XW 15,98 po (405,95mm) 8,39 po (213mm) 0,31 po (7,8mm) Bornes de Raccordement 14,41 po (366,13mm) 4,11 po (104,3mm) 9,94 po (252,6mm) Ouverture au plafond requise (y compris la tolérance) 8,64 x 14,66 po (219 x 372mm) Fig.
Fig. 5 : Monument 7XW 4,11 po (104,3mm) 10,6 po (269,2mm) 9,04 po (229,6mm) 0.
Foire aux questions Comment nettoyer mes enceintes? Utilisez un linge propre ou une brosse molle pour enlever la poussière sur vos enceintes. Ne vaporisez pas de produit nettoyant sur ou à proximité des hautparleurs. Quelle taille d’amplificateur dois-je utiliser? Nous recommandons un amplificateur homologué dans la gamme d’amplificateur approprié pour votre enceinte. avec d’excellents résultats.
Communiquer Avec le Service Le service à la clientèle de MartinLogan est disponible du lundi au vendredi, de 8 h à 17 h (heure normale du Centre) en composant le à la Clientèle (785) 749-0133 ou en envoyant un courriel à l’adresse service@martinlogan.com. Renseignements Généraux NUMÉRO DE SÉRIE Un numéro de série est situé derrière l’enceinte. Le numéro de série est également inscrit sur l’emballage du produit.
Comment être sûr de trouver un revendeur agréé MartinLogan? Seuls les revendeurs indiqués dans les pages suivantes sont des revendeurs agréés MartinLogan. Les produits achetés auprès d’une entité ne figurant pas sur ces listes ne bénéficient pas de la garantie limitée MartinLogan: • Revendeurs en ligne autorisés https://www.martinlogan.com/locator • Revendeurs américains autorisés https://www.martinlogan.com/locator • Distributeurs canadiens autorisés https://www.martinlogan.
Garantie en dehors des États-Unis et du Canada Cette garantie s’applique uniquement aux achats effectués auprès de revendeurs et distributeurs MartinLogan autorisés aux États-Unis et au Canada. Pour connaître les conditions de garantie et l’assistance ailleurs, veuillez contacter le distributeur agréé MartinLogan du pays où votre achat a été effectué. La garantie en dehors des États-Unis et du Canada est établie et fournie par les distributeurs agréés MartinLogan dans le monde entier.
Spécifications* Icon 3XW Réponse de fréquence du système . . . . . . . . . . 78–25 000 Hz ± 3 dB Haut-parleur haute dispersion (horizontale x verticale) . . 80° x 30° Sensibilité . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 dB à 2,83 volts/mètre Impédance . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 ohms. Compatible avec des amplificateurs classés 4, 6 ou 8 ohms. Fréquence de raccord . . . . . . . .
Tribute 5XW Monument 7XW 71–25 000 Hz ± 3 dB 52–25 000 Hz ± 3 dB 80° x 30° 80° x 30° 94 dB à 2,83 volts/mètre 95 dB à 2,83 volts/mètre 4 ohms. Compatible avec des amplificateurs classés 4, 6 ou 8 ohms. 4 ohms. Compatible avec des amplificateurs classés 4, 6 ou 8 ohms.
® Lawrence, Kansas, USA tél. 785.749.0133 téléc. 785.749.5320 www.martinlogan.com DuPont™ et Nomex® sont des marques ou des marques déposées de E.I. du Pont de Nemours and Company. ©2019 MartinLogan Ltd. All rights reserved. Tous droits réservés. Rev.