MARVEL OUTDOOR REFRIGERATED DRAWERS Installation Operation and Maintenance Instructions Outdoor 24” Refrigerated Drawers 6ORDE
UNPACKING YOUR OUTDOOR REFRIGERATED DRAWERS Remove Packaging Your outdoor refrigerated drawers have been packed for shipment with all parts that could be damaged by movement securely fastened. Before using, be sure all packing materials and tape have been removed. Important Keep your carton packaging until your refrigerated drawers have been thoroughly inspected and found to be in good condition. If there is damage, the packaging will be needed as proof of damage in transit.
INSTALLING YOUR OUTDOOR REFRIGERATED DRAWERS Select Location The proper location will ensure peak performance of your appliance. Choose a location where the unit will be out of direct sunlight and away from heat sources. Best performance will be maintained when installed within the following parameters: Unit should be operated in a properly ventilated area with ambient temperatures above 40 degrees and below 100 degrees Fahrenheit.
SENTRY SYSTEM™ REFRIGERATION MONITOR 38 Start Your Appliance Your appliance will start upon initial plug-in. The LED will flash amber upon initial plug-in due to your unit being powered-on at the factory to verify performance and then powered-off. The Sentry System™ refrigeration monitor senses a power outage has occurred and relays this information to you when you initially power-up your appliance. This is normal and pressing the “ON/OFF” button will reset this alarm function.
FULL OVERLAY PANEL INSTALLATION INSTRUCTIONS Step 1: Determine Wood Screw Requirements 1. A #8 pan head wood screw should be used to properly secure the overlay panel. A total of 8 screws will be needed. 2. Use only pan head screws. 3. Do not select a screw that is longer thant he wood thickness at the screw locations. 4. Use recommeded pilot holes for the frame material (see Table A below).
FULL OVERLAY PANEL INSTALLATION INSTRUCTIONS Step 3: Size the Overlay Panel Step 6: Reinstall the Drawers 1. Fully extend drawer slides and place drawer on slides. Be sure that drawer sits evenly on both slides. 2. Lock drawers into drawer slides. Push drawer locks down and then back to relock the drawer into the slide. Step 7: Adjust Drawer Front 1.
CARE AND CLEANING OF YOUR OUTDOOR REFRIGERATED DRAWERS Condenser The condenser tubing inside the cabinet does not require frequent cleaning; however, satisfactory cooling depends on adequate ventilation over the coils. Be sure that nothing obstructs the required air flow openings in front of the cabinet. At least once or twice a year, brush or vacuum lint and dirt from the condenser for efficient performance by unscrewing the grille on the bottom front of the cabinet.
TROUBLESHOOTING YOUR OUTDOOR REFRIGERATED DRAWERS Before Calling for Service Before calling for service, check the troubleshooting table on this page. This table lists possible problems that you can remedy without difficulty to avoid an unnecessary service call. PROBLEM Odor in cabinet Noisy operation Cabinet vibrates Cabinet light not working POSSIBLE CAUSES/SOLUTIONS 1. Interior needs cleaning 1. Cabinet not level 2. Weak floor 1. Cabinet not level 2. Weak floor 1. Tube burned out 2.
OBTAINING SERVICE FOR YOUR OUTDOOR REFRIGERATED DRAWERS If You Do Need Service If you do need service, contact your dealer or Marvel Industries. In any correspondence, refer to the model number and serial number of your unit which is located on the upper left hand side of the inside wall liner. Retain your proof of purchase. You may want to record these numbers in the space below.
HOUSEHOLD PRODUCT WARRANTY Entire Product Limited One Year Parts and Labor Warranty Marvel warrants that it will supply all necessary parts and labor to repair or replace in the end user’s home or office, any component which proves to be defective in material or workmanship, subject to the condition and exclusions stated below, for a period of one year from the date of purchase by the end user.
NOTES 10
www.lifeluxurymarvel.com Marvel Industries P.O. Box 997 Richmond, IN 47375-0997 800.428.6644 An AGA Company 41010649 Rev. C 03.03.08 All specifications and product designs subject to change without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions, replacements or compensation for previously purchased products.
