MARVEL Installation Operation and Maintenance Instructions Beverage and Wine Refrigerators Chateau Collection 3SBARE 6SBARE 8SBARE
TABLE OF CONTENTS Unpacking your beverage refrigerator.............................2 Removing the packaging.............................................2 Warranty Registration ..................................................2 Installing your beverage refrigerator................................3 Selecting the location..................................................3 Cabinet Clearances ....................................................3 Leveling legs ....................................................
UNPACKING YOUR BEVERAGE REFRIGERATOR Important Safety Instructions Warnings and safety instructions appearing in this guide are not meant to cover all possible conditions and situations that may occur. Common sense, caution, and care must be exercised when installing, maintaining, or operating this appliance. Recognize Safety Symbols, Words, and Labels. CAUTION-Hazards or unsafe practices which could result in personal injury or property or product damage.
INSTALLING YOUR BEVERAGE REFRIGERATOR Select Location The proper location will ensure peak performance of your appliance. We recommend a location where the unit will be out of direct sunlight and away from heat sources. To assure your product performs to specifications the recommended installation location temperature range is from 65 to 80°F (18 to 27°C) for indoor built in units and 65 to 90°F (18 to 32°C) for indoor freestanding units.
USING YOUR Sentry System™ CONTROL Glass Door Model LED Figure 3 Solid Door Model LED Figure 4 Start Your Appliance Please observe the following options when starting your appliance during initial plug-in. 1) If Sentry System™ LED is flashing amber (see Figure 3 or 4) the appliance is on. Simply press and release “ON/ OFF” button to stop the flashing LED. 2) If the interior light is working but Sentry System™ display is blank push and hold “ON/OFF” button for five (5) seconds to start the appliance.
DIMENSIONS FOR 3SBARE GLASS DOOR 37” (93.98cm) 16-9/16” (39.52cm) 25-7/32 (64.06cm) 14-7/8” (37.78cm) 23-9/32 (59.13cm) 34-1/4” to 34-1/2” (87 to 87.6 cm) 3” to 3-1/4” (7.62 to 8.26cm) 21-3/16” (53.82cm) Rough In Opening Dimensions, for 3SBARE Glass Door Electrical Requirements: 115 volts, 3.3 amps running max. 15 amp dedicated circuit required. 3 prong grounded receptacle required. 34-1/2” (87.6 cm) Power outlet can be located in the back wall behind unit.
DIMENSIONS FOR 3SBARE GLASS OVERLAY DOOR 36-27/32 (93.57cm) 13-29/32” (35.33cm) 23-1/4” (59.06cm) 14-7/8” (37.78cm) 22-17/32” (57.23cm) 34-1/4” to 34-1/2” (87 to 87.6cm) 3” to 3-1/4” (7.62 to 8.26cm) 21-3/16” (53.82cm) Rough In Opening Dimensions for 3SBARE Glass Overlay Door Electrical Requirements: 115 volts, 3.3 amps running max. 15 amp dedicated circuit required. 3 prong grounded receptacle required. 34-1/2” (87.6 cm) Power outlet can be located in the back wall behind unit.
DIMENSIONS FOR 3SBARE SOLID OVERLAY DOOR 37-5/32” (94.39cm) 13-7/8” (35.26cm) 23-1/4” (59.06cm) 22-17/32” (57.23cm) 14-7/8” (37.78cm) 34-1/4” to 34-1/2” (87 to 87.6cm) 3” to 3-1/4” (7.62 to 8.26cm) 21-3/16” (53.82cm) Rough In Opening Dimensions for 3SBARE Solid Overlay Door Electrical Requirements: 115 volts, 3.3 amps running max. 15 amp dedicated circuit required. 3 prong grounded receptacle required. 34-1/2” (87.6 cm) Power outlet can be located in the back wall behind unit.
DIMENSIONS FOR 6SBARE GLASS DOOR 47” (119.38cm) 25-21/32” (65.15cm) 26” (66.04cm) 23-7/8” (60.66cm) 24-1/16” (61.1cm) 34-1/4” to 34-1/2” (87 to 87.6cm) 3” to 3-1/4” (7.62 to 8.26cm) 22” (55.88cm) Rough In Opening Dimensions for 6SBARE Glass Door Electrical Requirements: 115 volts, 3.3 amps running max. 15 amp dedicated circuit required. 3 prong grounded receptacle required. 34-1/2” (87.6 cm) Power outlet can be located in the back wall behind unit.
DIMENSIONS FOR 6SBARE GLASS OVERLAY DOOR 46-25/32 (118.82cm) 23-1/32” (58.5cm) 23-7/8” (60.66cm) 24-1/16” (61.1cm) 34-1/4” to 34-1/2” (87 to 87.6cm) 3” to 3-1/4” (7.62 to 8.26cm) 22” (55.88cm) 23-5/16” (59.21cm) Rough In Opening Dimensions for 6SBARE Glass Overlay Door Electrical Requirements: 115 volts, 3.3 amps running max. 15 amp dedicated circuit required. 3 prong grounded receptacle required. 34-1/2” (87.6 cm) Power outlet can be located in the back wall behind unit.
DIMENSIONS FOR 6SBARE SOLID OVERLAY DOOR 46-27/32” (119.02cm) 23” (58.42cm) 23-7/8” (60.66cm) 24-1/16” (61.1cm) 34-1/4” to 34-1/2” (87 to 87.6cm) 3” to 3-1/4” (7.62 to 8.26cm) 22” (55.88cm) 23-5/16” (59.21cm) Rough In Opening Dimensions for 6SBARE Solid Overlay Door Electrical Requirements: 115 volts, 3.3 amps running max. 15 amp dedicated circuit required. 3 prong grounded receptacle required. 34-1/2” (87.6 cm) Power outlet can be located in the back wall behind unit.
DIMENSIONS FOR 8SBARE GLASS DOOR 52-31/32” (134.54cm) 31-23/32” (80.57cm) 29-7/8” (75.9cm) 26” (66.04cm) 34-1/4” to 34-1/2” (87 to 87.6cm) 22” (55.88cm) 3” to 3-1/4” (7.62 to 8.26cm) 24-1/16” (61.1cm) Rough In Opening Dimensions for 8SBARE Glass Door Electrical Requirements: 115 volts, 3.3 amps running max. 15 amp dedicated circuit required. 3 prong grounded receptacle required. 34-1/2” (87.6 cm) Power outlet can be located in the back wall behind unit.
DIMENSIONS FOR 8SBARE GLASS OVERLAY DOOR 52-21/32” (133.73cm) 29-1/16” (73.81cm) 29-7/8” (75.9cm) 24-1/16” (61.1cm) 34-1/4” to 34-1/2” (87 to 87.6cm) 3” to 3-1/4” (7.62 to 8.26cm) 22” (55.88cm) 23-5/16” (59.21cm) Rough In Opening Dimensions for 8SBARE Glass Overlay Door Electrical Requirements: 115 volts, 3.3 amps running max. 15 amp dedicated circuit required. 3 prong grounded receptacle required. 34-1/2” (87.6 cm) Power outlet can be located in the back wall behind unit.
FULL OVERLAY PANEL INSTALLATION INSTRUCTIONS Step 1: Verify door alignment The door should be parallel to the sides and top of the refrigerator. If alignment is necessary the door may be adjusted by loosening the 2 screws which secure the hinge adapter brackets to the door and adjusting the door side to side. Use a 5/32” allen wrench for this procedure. (See Figure 5 below). Top hinge pin remove to remove the door.
FULL OVERLAY PANEL INSTALLATION INSTRUCTIONS W Material Type #8 Wood Screw Hardwood 3/32” (2.4mm) Diameter. Pilot Hole Softwood 5/64 (2.0mm) Diameter. Pilot Hole Table C NOTE 1-23/32” Typical 4 (38.77cm) Sides H Front of overlay panel Figure 8 Glass Door Models Model W H 3SBARE 14-5/16” (36.35cm) 30-5/16” (76.99cm) 6SBARE 23-7/16” (59.54cm) 30-5/16” (76.99cm) 8SBARE 29-7/16” (74.78cm) 30-5/16” (76.
FULL OVERLAY PANEL INSTALLATION INSTRUCTIONS Figure 10 Step 9: Secure overlay panel to the door. With the #8 wood screws provided fasten the overlay panel to the door. (See Figure 11). Step 10: Install lock cam (Models with locks only). Attach the lock cam to the back of the lock assembly with the phillips head machine screw provided. Orient the lock cam vertically when installing on the lock. Step 11: Install door gasket Press the door gasket into the door channel.
FEATURES FOR BEVERAGE REFRIGERATORS Insert Wine Bottles The wine rack roll-out shelf holds four (4) bottles to ten (10) bottles of wine depending on model. See Figure 13 to 15 for typical wine bottle orientation. Loading Tips and Suggestions Your beverage center comes with sliding glass shelves and (1) wine shelf. The wine shelf should be located in the lowest position in the cabinet followed by a glass shelf directly above.
CARE AND CLEANING Condenser The condenser tubing inside the cabinet does not require frequent cleaning; however, satisfactory cooling depends on adequate ventilation over the coils. Be sure that nothing obstructs the required air flow openings in front of the cabinet. At least once or twice a year, brush or vacuum lint and dirt from the front grille area (see page 3).
CARE AND CLEANING Light Tube Replacement The light tubes are not covered by your warranty. Replacement tubes can be obtained from your dealer or from Northland-Marvel. DISCONNECT THE POWER CORD BEFORE ATTEMPTING LIGHT TUBE REPLACEMENT. Failure to do so may result in an electrical shock that could severely injure you. In the Event of a Power Failure If a power failure occurs, try to correct it as soon as possible.
TROUBLESHOOTING YOUR BEVERAGE REFRIGERATOR Before You Call for Service If the unit appears to be malfunctioning, read through this manual first. If the problem persists, check the troubleshooting guide below. Locate the problem in the guide and refer to the cause and its remedy before calling for service. The problem may be something very simple that can be solved without a service call. Some remedies listed in the Troubleshooting Guide are very complex.
HOW TO OBTAIN SERVICE If Service is Required: • If the product is within the first year warranty period please call Marvel Customer Service at 800.223.3900 for directions on how to obtain warranty coverage in your area. • If the product is outside the first year warranty period, Marvel Customer Service can provide recommendations of service centers in your area. A listing of authorized service centers is also available at www.marvelrefrigeration.com under the service and support section.
HOUSEHOLD PRODUCT WARRANTY Entire Product Limited One Year Parts and Labor Warranty Marvel warrants that it will supply all necessary parts and labor to repair or replace in the end user’s home or office, any component which proves to be defective in material or workmanship, subject to the condition and exclusions stated below, for a period of one year from the date of purchase by the end user.
NOTES 22
www.marvelrefrigeration.com Northland-Marvel P.O. Box 400 1260 E. Van Deinse St. Greenville MI 48838 800.223.3900 41011767-EN Rev J 12/05/09 All specifications and product designs subject to change without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions, replacements or compensation for previously purchased products.