EN Installation, Operation and Maintenance Instructions FR Instructions d’installation, d’utilisation et d’entretien ES Instrucciones de instalación, operación y mantenimiento Refrigerators Réfrigérateurs Refrigeradores ML15BC ML24BC MA24BC ML24BR MA24BR ML15RA ML24RA MA24RA
CONTENTS Contents: Important Safety Instructions Safety information ...............................................................2 Unpacking your appliance ..................................................3 Warranty registration .....................................................3 Installing your appliance ......................................................4 Cabinet clearances .........................................................4 Leveling the appliance ........................................
UNPACKING YOUR APPLIANCE ! Warranty Registration WARNING It is important you send in your warranty registration card immediately after taking delivery of your appliance or you can register online at www.agamarvel.com. EXCESSIVE WEIGHT HAZARD Use two or more people to move product. Failure to do so can result in personal injury. The following information will be required when registering your appliance.
INSTALLING YOUR APPLIANCE Select Location The proper location will ensure peak performance of your appliance. We recommend a location where the unit will be out of direct sunlight and away from heat sources. To ensure your product performs to specifications, the recommended installation location temperature range is from 55 to 100°F (13 to 38°C). Front Grille, keep this area open. Cabinet Clearance Ventilation is required from the bottom front of the appliance.
INSTALLING YOUR APPLIANCE ! WARNING Electrical Shock Hazard • Do not use an extension cord with this appliance. They can be hazardous and can degrade product performance. • This appliance should not, under any circumstances, be installed to an un-grounded electrical supply. • Do not remove the grounding prong from the power cord. • Do not use an adapter. • Do not splash or spray water from a hose on the appliance. Doing so may cause an electrical shock, which may result in severe injury or death.
INSTALLING THE ANTI TIP DEVICE Anti-Tip Bracket WARNING ! • ALL APPLIANCES CAN TIP RESULTING IN INJURY. • INSTALL THE ANTI-TIP BRACKET PACKED WITH THE APPLIANCE. • FOLLOW THE INSTRUCTIONS BELOW 211⁄2" (54.
INSTALLING THE ANTI TIP DEVICE ! WARNING TIP OVER HAZARD: One of the rear cabinet leveling legs must be engaged under an anti-tip bracket. NOTE When the floor mounted anti-tip bracket is used the minimum adjusted height of the cabinet is increased by 3 ⁄8" (9 mm). nt o Fro net bi f ca line Sid eo f c Rear Leveling leg ab ine t li ne Screw 211⁄2" (54.
PRODUCT DIMENSIONS ROUGH-IN OPENING DIMENSIONS CABINET DIMENSIONS MODEL "A" "B" "C" "D" "E" "F" "G" "H" "J" ML15**(G) or (S) 15" (38.1 cm) **34" to 35" (86.4 to 88.9 cm) * 147⁄8" (37.8 cm) 333⁄4" to 343⁄4" (85.7 to 88.3 cm) 2323⁄32" (60.2 cm) 2521⁄32" (65.2 cm) 3713⁄32" (95 cm) 1611⁄16" (42.4 cm) ML15**(P) or (F) 15" (38.1 cm) **341⁄4" to 351⁄4" (87 to 89.5 cm) * 147⁄8" (37.8 cm) 34" to 35" (86.4 to 88.9 cm) 227⁄8" (58.1 cm) - 371⁄2" (95.2 cm) 141⁄8" 35.
PRODUCT DIMENSIONS PRODUCT DATA MODEL ELECTRICAL REQUIREMENTS # PRODUCT WEIGHT ML15**(G) or (S) 115V/60Hz/15A 105 lbs (47.7 kg) ML15**(P) or (F) 115V/60Hz/15A 105 lbs (47.7 kg) ML24**(G) or (S) 115V/60Hz/15A 140 lbs (63.6 kg) ML24**(P) or (F) 115V/60Hz/15A 140 lbs (63.6 kg) MA24**(G) or (S) 115V/60Hz/15A 140 lbs (63.6 kg) MA24**(P) or (F) 115V/60Hz/15A 140 lbs ((63.6 kg) "J" "H" "D" "G" "E" 211⁄2" (54.
USING YOUR ELECTRONIC CONTROL Temp Minus keypad On/Off keypad Temp Plus keypad Lights keypad (glass door Lock keypad only) Display Area System Status indicators Figure 9 Electronic single zone control Power Failure ALARM RESET To wake the display press any keypad. A confirm tone will sound, and the current storage compartment temperature will be displayed. Starting your appliance: Plug the appliance power cord into a 115 volt wall outlet.
USING YOUR ELECTRONIC CONTROL Interior display lighting: (Glass door models only) Your appliance is equipped with a dual light level display lighting feature. With the control out of sleep mode press the "Light" keypad once to activate the interior lighting display feature at full illumination. A confirmation tone will sound, and the light bulb "Icon" will illuminate. Pressing the "Light" keypad a 2nd time will dim the lighting to 50%. A 3rd press will deactivate the display lighting feature.
USING YOUR ELECTRONIC CONTROL Alarms: The control will alert you to conditions that could adversely affect the performance of the appliance. Temp • Door Ajar ALARM RESET • Door ajar - If the door is open, or not closed prop- erly, for more than 5-minutes the System Status OK indicator will turn-off, the "Door Ajar" indicator will flash, and a tone will sound every 60 seconds. Additionally, an "ALARM RESET" indicator will be displayed below the "On/Off" keypad.
USING YOUR ELECTRONIC CONTROL Vacation mode: This operating mode can be used to save energy during high cost energy periods, or when you won't be using your appliance for an extended period of time by disabling the lights, alarm tones, and keypad entry tones. Vacation mode also serves as a Sabbath mode, disabling functions and its controls in accordance with the weekly Sabbath and religious holidays observed within the Orthodox Jewish community.
OVERLAY DOOR PANEL INSTALLATION If you purchased an overlay panel model, your unit is equipped with articulated hinges to allow fully integrated built-in installations. Custom panel thicknesses of 5⁄8" (15 mm) and 3⁄4" (18 mm) are accommodated. ! ! WARNING Use extreme caution with the articulated hinges. The hinge is self closing and many pinch points exist prior to built-in installation. Do not remove the cabinet "Z" bracket from the top of the cabinet.
OVERLAY DOOR PANEL INSTALLATION Step 2: Remove the door gasket With the door laying on a flat surface and starting at a corner of the door remove the magnetic door gasket from the interior side of the door, see Figure 12. Set the gasket aside on a flat surface. Overlay panel flush with top of door. There are 10 holes in the gasket retainer extrusions, (3 on each side and 2 at the top and bottom which are used to fasten the panel to the front of the door.
OVERLAY DOOR PANEL INSTALLATION Clearance for screw head, 4 places f po Hinge side of door Figure 13 Left Hand Hinged Door 15" (38.1 cm) wide appliance Clearance for screw head, 4 places Hinge side of door To or do Figure 15 Right Hand Hinged Door 15" (38.1 cm) wide appliance Clearance for hinge 2 places Clearance for hinge 2 places 143⁄4" (37.5 cm) 1" (25.4 mm) diameter counter bore 1⁄4" (6 mm) deep 4 places. 1 ⁄4" (6 mm) Deep 1 143⁄4" (37.5 cm) ⁄4" (6 mm) Deep 47⁄8" 5" (12.7 cm) (12.
OVERLAY DOOR PANEL INSTALLATION r oo d of CAUTION Weight of overlay door panel must not exceed 15 pounds (6.8 kg) for a solid door model or 10 pounds (4.5 kg) for a glass door model. Hinge side of door p To ! 233⁄4" (60.3 cm) ⁄4" (6 mm) Deep 1 do or 233⁄4" (60.3 cm) 1 ⁄4" (6 mm) Deep 13⁄4" (4.4 cm) 13⁄4" (4.4 cm) 13⁄16" (3 cm) of Clearance for hinge at top and bottom Clearance for hinge at top and bottom 14" (35.
OVERLAY DOOR PANEL INSTALLATION Step 4: Assemble the panel to the door The preferred method of attaching the panel to the door is to clamp the panel to the door so it cannot move while drilling the screw pilot holes. Use bar clamps or "C" clamps with pads on the clamping surfaces that will not mar the panel or the door. The custom overlay panel should be flush with the top of the door and centered along the width of the door. See Figure 12a.
OVERLAY DOOR PANEL INSTALLATION Step 5: Assemble lock parts Two (2) lock extensions are provided with the lock. Use the longer extension for 3⁄4" thick overlay panels and the shorter one for 5⁄8" thick overlay panels. Assemble the lock extension, cam stop washer, spring washer, and set screw to the lock as shown in Figure 21 and 23. Counter bore lock hole on back side.
OVERLAY DOOR PANEL INSTALLATION 1.234" (31.3 mm) .991" (25.2 mm) Figure 23 Step 7: Install the door Carefully open the top and bottom hinges on the door being careful as there are many pinch points. Place the hinges over the 4 screws in the cabinet, 2 at the top and 2 at the bottom and slide the door into position. Tighten the 4 hinge screws with a phillips screwdriver. (See Figures 10 and 10a).
SHELVING CONFIGURATIONS Loading Tips and Suggestions Your appliance is equipped with a cantilever shelf system which provides maximum adjust ability and customizing of the shelving arrangements listed below. Beverage Refrigerator: 24" (61 cm) Wide Models: Shown with a glass door. Figure 27. (1) half width flat glass cantilever shelf. (See Figure 32). (1) wine cutout and flat glass cantilever shelf. (See Figure 34). (1) frame and flat glass crisper cover.
SHELVING CONFIGURATIONS Refrigerator: 24" (61 cm) Wide Models: Shown with a solid door with door racks. Figure 30. (1) half width flat glass cantilever shelf. (See Figure 33). (1) frame and slumped glass cantilever shelf. (1) frame and flat glass crisper cover. (1) roll-out crisper pan. (1) full width door storage rack. (1) half width door storage rack.
SHELVING CONFIGURATIONS ! To Add or Remove a Shelf CAUTION Make sure your cantilever shelf is secure on the shelf supports by pressing down on the shelf before loading. Installed shelf tang Shelf support slot Remove stored product from the shelf. Do not try to remove a loaded shelf from the appliance. Grasp the shelf front with both hands, rotate the front upward and lift out. (See Figure 36b).
CARE AND CLEANING AND ENERGY SAVING TIPS Front Grille Be sure that nothing obstructs the required air flow openings in front of the cabinet. At least once or twice a year, brush or vacuum lint and dirt from the front grille area (see page 4). ! CAUTION SHOCK HAZARD: Disconnect electrical power from the appliance before cleaning with soap and water. Cabinet The painted cabinet can be washed with either a mild soap and water and thoroughly rinsed with clear water. NEVER use abrasive scouring cleaners.
DOOR ALIGNMENT AND OBTAINING SERVICE Door alignment for solid and glass door models: The door should be parallel to the sides and top of the appliance. If alignment is necessary the door may be adjusted by loosening the 2 screws which secure the door adjustment bracket on the bottom of the door (see Figure 37a) and adjusting the door side to side. Use a 5⁄32” allen wrench for this procedure. (See Figure 37 below). When finished aligning the door, tighten the screws securely.
TROUBLESHOOTING Before You Call for Service Problem Appliance not cold enough WARNING ! If the appliance appears to be malfunctioning, read through this manual first. If the problem persists, check the troubleshooting guide below. Locate the problem in the guide and refer to the cause and its remedy before calling for service. The problem may be something very simple that can be solved without a service call. However, it may be required to contact your dealer or a qualified service technician.
HOUSEHOLD PRODUCT WARRANTY Entire Product Limited One Year Parts and Labor Warranty Parts or Service Not Supplied or Designated by AGA MARVEL AGA MARVEL warrants that it will supply all necessary parts and labor to repair or replace in the end user’s home or office, any component which proves to be defective in material or workmanship, subject to the condition and exclusions stated below, for a period of one year from the date of purchase by the end user.
www.agamarvel.com 1260 E. VanDeinse St. Greenville MI 48838 800.223.3900 41013316-EN Rev F 11/5/14 All specifications and product designs subject to change without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions, replacements or compensation for previously purchased products.