EN Installation, Operation and Maintenance Instructions FR Instructions d’installation, d’utilisation et d’entretien ES Instrucciones de instalación, operación y mantenimiento Wine Cellars Celliers Bodegas para vinos ML15WS ML24WS ML24WD Note: Wine Cellars are designed exclusively for the storage of wine. Wine Cellars cannot attain storage temperatures suitable for fresh food storage. Remarque : Les celliers sont conçues exclusivement pour y garder des vins.
CONTENTS Important Safety Instructions Contents: Warnings and safety instructions appearing in this guide are not meant to cover all possible conditions and situations that may occur. Common sense, caution, and care must be exercised when installing, maintaining, or operating this appliance. Safety information ...............................................................2 Unpacking your appliance ..................................................3 Warranty registration .................................
UNPACKING YOUR APPLIANCE ! Warranty Registration WARNING It is important you send in your warranty registration card immediately after taking delivery of your appliance or you can register online at www.agamarvel.com. EXCESSIVE WEIGHT HAZARD Use two or more people to move product. Failure to do so can result in personal injury. The following information will be required when registering your appliance.
INSTALLING YOUR APPLIANCE Select Location The proper location will ensure peak performance of your appliance. We recommend a location where the unit will be out of direct sunlight and away from heat sources. To ensure your product performs to specifications, the recommended installation location temperature range is from 55 to 100°F (13 to 38°C). Front Grille, keep this area open. Cabinet Clearance Ventilation is required from the bottom front of the appliance.
INSTALLING YOUR APPLIANCE ! WARNING Electrical Shock Hazard • Do not use an extension cord with this appliance. They can be hazardous and can degrade product performance. • This appliance should not, under any circumstances, be installed to an un-grounded electrical supply. • Do not remove the grounding prong from the power cord. • Do not use an adapter. • Do not splash or spray water from a hose on the appliance. Doing so may cause an electrical shock, which may result in severe injury or death.
INSTALLING THE ANTI TIP DEVICE Anti-Tip Bracket WARNING ! • ALL APPLIANCES CAN TIP RESULTING IN INJURY. • INSTALL THE ANTI-TIP BRACKET PACKED WITH THE APPLIANCE. • FOLLOW THE INSTRUCTIONS BELOW 211⁄2" (54.
INSTALLING THE ANTI TIP DEVICE ! WARNING TIP OVER HAZARD: One of the rear cabinet leveling legs must be engaged under an anti-tip bracket. NOTE When the floor mounted anti-tip bracket is used the minimum adjusted height of the cabinet is increased by 3 ⁄8" (9 mm). nt o Fro net bi f ca line Sid eo f c Rear Leveling leg ab ine t li ne Figure 6a Screw 211⁄2" (54.
PRODUCT DIMENSIONS ROUGH-IN OPENING DIMENSIONS CABINET DIMENSIONS MODEL "A" "B" "C" "D" "E" "F" "G" "H" "J" ML15WSG 15" (38.1 cm) **34" to 35" (86.4 to 88.9 cm) * 147⁄8" (37.8 cm) 333⁄4" to 343⁄4" (85.7 to 88.3 cm) 2323⁄32" (60.2 cm) 2521⁄32" (65.2 cm) 3713⁄32" (95 cm) 1611⁄16" (42.4 cm) ML15WS(P) or (F) 15" (38.1 cm) **34 ⁄4" to 35 ⁄4" (87 to 89.5 cm) * 147⁄8" (37.8 cm) 34" to 35" (86.4 to 88.9 cm) 227⁄8" (58.1 cm) - 371⁄2" (95.2 cm) 141⁄8" 35.
PRODUCT DIMENSIONS PRODUCT DATA MODEL ELECTRICAL REQUIREMENTS # PRODUCT WEIGHT ML15WSG 115V/60Hz/15A 105 lbs (47.7 kg) ML15WS(P) or (F) 115V/60Hz/15A 105 lbs (47.7 kg) ML24W*G 115V/60Hz/15A 140 lbs (63.6 kg) ML24W*(P) or (F) 115V/60Hz/15A 140 lbs (63.6 kg) "J" "H" "D" "G" "E" 1" (2.5 cm) Figure 8 211⁄2" (54.6cm) "F" * Depth dimension of rough-in opening may vary depending on each individual installation. To recess entire door "F" dimension plus 1" (2.
USING YOUR ELECTRONIC CONTROL Temp Minus keypad On/Off keypad Upper/Lower Temp zones Plus (Dual Zone keypad models only) Lights keypad (glass door Lock only) keypad Display Area System Status indicators Figure 9 Electronic control Power Failure ALARM RESET To wake the display press any keypad. A confirm tone will sound, and the current storage compartment temperature will be displayed. Starting your appliance (Single and Dual Zone: Plug the appliance power cord into a 115 volt wall outlet.
USING YOUR ELECTRONIC CONTROL Adjusting the temperature: Lower zone selected NOTE When initially loading your product with warm contents, it may take up to 48-hours for the storage compartment temperature to stabilize. When making temperature set-point changes, it may take up to 24-hours for the stored contents to stabilize at your new set-point temperature. Factors that affect the storage compartment stabilized temperature: • Changes to temperature setting. • Room temperature changes.
USING YOUR ELECTRONIC CONTROL Power Failure Temperature mode (Single and Dual Zone): • The temperature mode is preset from the factory in Fahrenheit (°F) but you have the option to change it to Centigrade (°C). To change the mode, press and hold the "-" keypad, while pressing the "+" keypad, then release the "-" keypad. The temperature will now be displayed in Centigrade (°C). Repeat the procedure to change the temperature mode back to Fahrenheit (°F).
USING YOUR ELECTRONIC CONTROL Vacation mode (Single and Dual Zone): This operating mode can be used to save energy during high cost energy periods, or when you won't be using your appliance for an extended period of time by disabling the lights, alarm tones, and keypad entry tones. Vacation mode also serves as a Sabbath mode, disabling functions and its controls in accordance with the weekly Sabbath and religious holidays observed within the Orthodox Jewish community.
OVERLAY DOOR PANEL INSTALLATION If you purchased an overlay panel model, your unit is equipped with articulated hinges to allow fully integrated built-in installations. Custom panel thicknesses of 5⁄8" (15 mm) and 3⁄4" (18 mm) are accommodated. ! ! Use extreme caution with the articulated hinges. The hinge is self closing and many pinch points exist prior to built-in installation. Do not remove the cabinet "Z" bracket from the top of the cabinet.
OVERLAY DOOR PANEL INSTALLATION Press and hold down this tab on the wire connector and pull the connector apart. Figure 11 Hinge side of door Clearance for screw head, 4 places Figure 13 Left Hand Hinged Door 15" (38.1 cm) wide appliance Overlay panel flush with top and side of door. Clearance for hinge 2 places 143⁄4" (37.5 cm) Overlay panel to be centered on width of door. Holes in gasket retainer. 1 ⁄4" (6 mm) Deep 1" (25.4 mm) diameter counter bore 1⁄4" (6.4mm) 5" 47⁄8" deep 4 places. (12.
OVERLAY DOOR PANEL INSTALLATION ! Clearance for screw head, 4 places CAUTION Clearance for screw head, Weight of overlay door panel must not 4 places exceed 15 pounds (6.8 kg) for a solid door model or 10 pounds (4.5 kg) for a glass door model. Figure 15 Right Hand Hinged Door 15" (38.1 cm) wide appliance p To Figure 17 Left Hand Hinged Door 24" (61 cm) wide appliance Clearance for hinge 2 places 1 233⁄4" (60.3 cm) 47⁄8" 5" (12.4 cm) (12.7 cm) 13⁄4" (4.
OVERLAY DOOR PANEL INSTALLATION Clearance for hinge at top and bottom of do or ! Clearance for screw head, 4 places CAUTION Weight of overlay door panel must not exceed 15 pounds (6.8 kg) for a solid door model or 10 pounds (4.5 kg) for a glass door model. Hinge side of door To p Material Type #10 Wood Screw Hardwood 1 Softwood 7 ⁄8" (3.2 mm) Diameter. Pilot Hole ⁄64 (2.8 mm) Diameter.
OVERLAY DOOR PANEL INSTALLATION AND SHELVING CONFIGURATIONS Step 5: Install the door Carefully open the top and bottom hinges on the door being careful as there are many pinch points. Place the hinges over the 4 screws in the cabinet, 2 at the top and 2 at the bottom and slide the door into position. Tighten the 4 hinge screws with a phillips screwdriver. (See Figures 10 and 10a). Place wire harness from the grille and mount to the bottom of the door with the screw and "P" clamp removed in step 1.
SHELVING CONFIGURATIONS Figure 27 Dual Zone Wine Cellar: 24" (61 cm) Wide models: Figure 25 Upper Zone: (3) 8 bottle tray shelf with vibration dampening mat Lower Zone: (1) 8 bottle tray shelf with vibration dampening mat (2) 4 bottle half depth tray shelf with vibration dampening mat Single Zone Wine Cellar: 24" (61 cm) Wide models: (5) 8 bottle tray shelf with vibration dampening mat (1) 5 bottle rollout display rack with vibration dampening mat To remove a shelf: ! CAUTION Extend the shelf out
CARE AND CLEANING AND ENERGY SAVING TIPS Front Grille Be sure that nothing obstructs the required air flow openings in front of the cabinet. At least once or twice a year, brush or vacuum lint and dirt from the front grille area (see page 4). ! CAUTION SHOCK HAZARD: Disconnect electrical power from the appliance before cleaning with soap and water. Cabinet The painted cabinet can be washed with either a mild soap and water and thoroughly rinsed with clear water. NEVER use abrasive scouring cleaners.
DOOR ALIGNMENT AND OBTAINING SERVICE Door alignment for solid and glass door models: The door should be parallel to the sides and top of the appliance. If alignment is necessary the door may be adjusted by loosening the 2 screws which secure the door adjustment bracket on the bottom of the door (see Figure 28a) and adjusting the door side to side. Use a 5⁄32” allen wrench for this procedure. (See Figure 28 below). When finished aligning the door, tighten the screws securely.
TROUBLESHOOTING Before You Call for Service Problem Appliance not cold enough WARNING ! If the appliance appears to be malfunctioning, read through this manual first. If the problem persists, check the troubleshooting guide below. Locate the problem in the guide and refer to the cause and its remedy before calling for service. The problem may be something very simple that can be solved without a service call. However, it may be required to contact your dealer or a qualified service technician.
HOUSEHOLD PRODUCT WARRANTY Entire Product Limited One Year Parts and Labor Warranty Parts or Service Not Supplied or Designated by AGA MARVEL AGA MARVEL warrants that it will supply all necessary parts and labor to repair or replace in the end user’s home or office, any component which proves to be defective in material or workmanship, subject to the condition and exclusions stated below, for a period of one year from the date of purchase by the end user.
www.agamarvel.com 1260 E. VanDeinse St. Greenville MI 48838 800.223.3900 41013358-EN Rev E 11/5/14 All specifications and product designs subject to change without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions, replacements or compensation for previously purchased products.