Installation Operation and Maintenance Instructions Beverage Center MLBV024-SG01A
Installation Operation Instructions Installation Operationand andMaintenance Maintenance Instructions Contents Intro Safety Safety and Warning Disposal and Recycling Installation Environmental Requirements Electrical Cutout Dimensions Product Dimensions Water Hookup General Installation Overlay Panel Dimensions Overlay Panel Installation Grille Installation Door Swing Door Adjust Operating Instructions First Use Ice Airflow and Product Loading Maintenance Cleaning Cleaning Condenser Extended Non-Use Servic
Installation Operation Instructions Installation Operationand andMaintenance Maintenance Instructions Welcome to the Marvel Experience Congratulations on adding a new Marvel Built-in Undercounter Beverage Cooler to your home and thank you for choosing our quality American-built product. We are thrilled to welcome you to our growing community of Marvel owners, who trust in our products and our support.
Installation Operation and Maintenance Instructions Disposal and Recycling ! CAUTION ! DANGER Caution means that failure to follow this safety statement may result in minor or moderate personal injury, property, or equipment damage. RISK OF CHILD ENTRAPMENT. Before you throw away your old refrigerator or freezer, take off the doors and leave shelves in place so children may not easily climb ! DANGER inside. This unit contains R600a (Isobutane) which is a flammable hydrocarbon.
Installation Operation and Maintenance Instructions Environmental Requirements The unit requires a grounded and polarized 115 VAC, 60 This unit is designed to operate between 50°F (10°C) and individual, properly grounded branch circuit or circuit breaker 100°F (38°C). Higher ambient temperatures may reduce the is recommended.
Installation Operation and Maintenance Instructions Cutout & Product Dimensions 23 15⁄16” (608 mm) PREPARE SITE Your product has been designed for either free-standing or FRONT built-in installation. When built-in, your unit does not require additional air space for top, sides, or rear. However, the front 34 1⁄8” to 35 1⁄8” (867 mm to 892 mm) 28” (711 mm) grille must NOT be obstructed, and clearance is required for an electrical connection in the rear.
Installation Operation and Maintenance Instructions Side-by-Side Installation Anti-Tip Bracket Two units may be installed side-by-side. 1. Slide unit out so screws on top of unit are easily accessible. Cutout width for a side-by-side installation is the cutout dimension of a single unit times two. 2. Remove the two screws from the opposite side of the hinge assembly using a T-25 TORX driver (see below). No trim kit is required.
Installation Operation and Maintenance Instructions General Installation Grille Installation LEVELING INFORMATION REMOVING AND INSTALLING GRILLE 1. ! WARNING Use a level to confirm the unit is level. Level should Disconnect electric power to the unit before removing the be placed along top edge grille. and side edge as shown. When using the unit, the grille must be installed. 1 ! WARNING 2. If the unit is not level, adjust the legs on the corners of the DO NOT touch the condenser fins.
16-1/2" 16-1/2" Installation Operation and Maintenance Instructions 90° Door Swing Stainless Steel nd Wood Overlay Door Swing 3. 2175R(F) & 2275WC Models all 2-1/8" Min. (54 mm) Overlay in. m) 4. Tighten bottom hinge screws. 5. Tighten top hinge screws. Reversing the Door Location of the unit may make it desirable to mount the door on the opposite side of the cabinet. The hinge hardware will be removed and reinstalled on the opposite side of the cabinet.
Installation Operation and Maintenance Instructions 3. Install top hinge and door: Remove door by tilting forward and lifting door off bottom hinge. Retain shoulder washers; they will be reused. 4. 1. Remove four screws from hinge holes on the opposite Use alternate hinge supplied with unit and reinstall the screws. Do not tighten... side. Reinstall into holes where the hinge was removed. Take care not to scratch cabinet. Remove and reinstall bottom hinge: 1.
Installation Operation and Maintenance Instructions Control Operation CONTROL FUNCTION GUIDE FUNCTION COMMAND NOTES ON/OFF Press and hold for 5 seconds Unit will turn On or OFF Press and release to leave interior light After 3 hours, factory default is restored; light will turn on Leave interior light on on for 3 hours; press again to deactivate when door is open When the display is flashing, press Adjust Temperature Press or and release or to adjust the set point temperature.
Installation Operation and Maintenance Instructions Airflow and Product Loading NOTICE Restricting airflow may result in poor product performance, AIRFLOW product failure, and uneven internal temperatures and may freeze contents.
Installation Operation and Maintenance Instructions Interior Adjustments INTERIOR SHELVES Removing and Installing Interior Shelves 3 1 2 For models equipped with glass shelves having recessed shelf supports, remove the shelves as follows: 1. Pull shelf out about 6” (1), until back of shelf clears the “hump” on the right-hand side. 2. Tilt up right-hand edge of shelf (2). 3. Remove shelf from unit by pulling out (3). Insert the shelves as follows: 1.
Installation Operation and Maintenance Instructions Cleaning Do not use any solvent-based or abrasive cleaners. Stainless Models products and damage or discolor the lining. Stainless door panels and handles can discolor when DEFROSTING exposed to chlorine gas, pool chemicals, saltwater or Under normal conditions this unit does not require manual These types of cleaners may transfer taste to the interior cleaners with bleach. defrosting.
Installation Operation and Maintenance Instructions Cleaning Condenser Extended Non-Use INTERVAL - EVERY SIX MONTHS VACATION/HOLIDAY, PROLONGED SHUTDOWN To maintain operational efficiency, keep the front grille free The following steps are recommended for periods of extended of dust and lint, and clean the condenser when necessary. non-use: Depending on environmental conditions, more or less frequent cleaning may be necessary. 1. Remove all consumable content from the unit. 2.
Installation Operation and Maintenance Instructions Troubleshooting • Evaporator: Refrigerant flowing through an evaporator may sound like boiling liquid. BEFORE CALLING FOR SERVICE • Condenser Fan: Air moving through a condenser may be heard. • Automatic Defrost Drain Pan: Water may be heard dripping or running into the drain pan when the unit is in the defrost cycle. If you think your product is malfunctioning, read the CONTROL OPERATION section to clearly understand the function of the control.
Marvel Refrigeration Limited Warranty Marvel Refrigeration (Marvel) Limited Warranty ONE YEAR LIMITED PARTS & LABOR WARRANTY For one year from the date of original purchase, this warranty covers all parts and labor to repair or replace any part of the product that proves to be defective in materials or workmanship. For products installed and used for normal residential use, material cosmetic defects are included in this warranty, with coverage limited to 60 days from the date of original purchase.
Installation Operation Instructions Installation Operationand andMaintenance Maintenance Instructions If Service is Required: • If the product is within the first year warranty period please contact your dealer or call Marvel Customer Service at 800.223.3900 for directions on how to obtain warranty coverage in your area. • If the product is outside the first year warranty period, Marvel Customer Service can provide recommendations of service centers in your area.
Installation Operation and Maintenance Instructions 19
1260 E. VanDeinse St. Greenville, MI 48838 800.223.3900 www.marvelrefrigeration.