USER’S MANUAL WIRELESS MICROPHONE SYSTEM RS-21B / RS-22B
Contents: Introduction -------------------------------------------------------------------------- 1 Quick Start Guide ------------------------------------------------------------------ 2 Product Description ---------------------------------------------------------------- 4 System Operation ------------------------------------------------------------------ 8 Color Label Identification --------------------------------------------------------- 10 Basic Connections ----------------------------------------------
Introduction Thank you for purchasing our product. This PLL synthesized wireless microphone system operates in UHF band frequency with 8 selectable channels. Please read this instruction manual carefully before operating the system. This manual covers the function and operation of the wireless microphone system. FCC Statement This device complies with Part 15.236 of the FCC Rules.
Quick Start Guide 1. Connected Receiver Power Cable 2.
Quick Start Guide 3. Insert Batteries 2 4.
Receiver Front : RS-21B: Dual Channel Receiver 3 3 6 1 7 5 4 2 2 4 5 7 1. 2. 3. 4. 5. 6. 7. Power Button AF Indicator: Display the reception status of AF signal. RF Indicator: Display the reception status of RF signal. LED Display: Display selected channel. Channel Selector: Tap the channel backward. Fixed UHF Antenna Volume Control: Adjust the receiver output level. Rear : SQ MIC DC 12V 500mA 1 3 4 2 1 3 4 5 1. 2. 3. 4. 5. Unbalanced 6.
Receiver Front : RS-22B: Dual Channel Receiver 1 1. 2. 3. 4. 5. 6. 7. 2 4 5 7 2 4 5 7 Power Button AF Indicator: Display the reception status of AF signal. RF Indicator: Display the reception status of RF signal. LED Display: Display selected channel. Channel Selector: Tap the channel backward. Fixed UHF Antenna Volume Control: Adjust the receiver output level. Rear : SQ MIC DC 12V 500mA 5 1. 2. 3. 4. 5. Unbalanced 6.
UF-21B Handheld Microphone 1. Grille: Protects the microphone capsule and helps reduce breath sounds and wind noise. 2. Talk Switch: Push the switch up to talk. Push the switch down for mute. 3. Channel Selector: 8 different selectable channels. 4. Battery Compartment: Insert two AA size batteries into the compartment and make sure that the polarity of batteries is correct. 5. Power LED: Indicate the power / low battery level status.
UT-16B Bodypack Transmitter 1. 2. 3. 4. 5. 6. 7. Power Button: Press for 2 seconds to power the microphone on or off. Mute Button: With the transmitter on, a slight press for button will toggle between mute and unmute function. Power LED: Indicate the power / low battery level status. LED Indicator Status Green Ready Flashing Red Low battery power when less than 10 minutes operation Channel Selector: 8 different selectable channels.
Connecting the receiver Prior to setting up, please check that the transmitter and receiver are tuned to the same frequency or channel. Two or more transmitters operating in the same frequency can not be used at the same time and area. Connected the provided DC power supply to the receiver power input with an appropriate AC power source. The LED display will light and the receiver is on. Using a standard audio cable with 6.3mm phone plugs to connect the mixer or amplifier.
Set up the handheld microphone / bodypack transmitter Open the battery cover and insert batteries into the battery compartment conforming to the polarity (+)(-) marks. Counterclockwise loosen the battery cover and insert two AA batteries into the compartment. Be careful to observe the correct polarity when replacing the batteries. Connect to the lavalier microphone, headset microphone or guitar cable.
Color Label Identification You can also stick the color label on the receiver and transmitter for quickly identify the pair system.
Basic Connections To install a receiver in a 19” standard rack by using 2 short L type metal racks. L4 To mount a receiver in a 19” standard rack by using 2 long L type metal racks. (L type long metal racks is an optional product, so please purchase extra in local shops.
Trouble Shooting whether is set too high or too low.
System Performance Receiver Frequency Range Case Oscillator Modulation S/N Ratio Image & Spurious Rejection Receiving Sensitivity AF Response T.H.D. IF Frequency Dynamic Range Tone Signal Audio Output Power Supply Current Consumption Dimension(mm) WxHxD Weight : UHF510 ~ 937.
440-XXXX-X