Installation Guide

ManualsBrandsMasonite ManualsDoors & Windows36 in. x 80 in. Utility 6-Panel Right-Hand Outswing Primed Steel Prehung Front Exterior Door

Staining:

1. Put on gloves and prepare your materials.

2. Stir stain thoroughly using smooth strokes, avoid creating

bubbles and do not shake the stain container.

3. Working in the specified order and individual section, dip the

foam brush into the stain then use the rim of the container to

release any excess. Use the foam brush to apply the stain onto the

section. Using a cloth, rub the stain into the embossed woodgrain

ensuring complete and even coverage. Stop between sections to

tidy up the perimeter with a rag and mineral spirits. Clean edges

will help define the individual components of the door.

If preferred, the subtle color variation found in wood can be

replicated by selective removal of the stain. Using a rag or cheese

cloth, gently rub the surface removing very small amounts of

stain. Apply varying levels of pressure and work in the direction

of the grain. Excessive pressure will remove too much stain.

4. Once the door has been completely stained, check for any drips.

While the stain is still wet, lightly brush the entire surface of the

door with a china bristle brush. Use long strokes and work in the

direction of the grain to even out color and achieve consistency.

5. Let the first stained surface dry, per the stain manufacturer’s

recommended drying time, before proceeding to the second side.

6. If you prefer a darker appearance, repeat staining steps

one through five only after first coat is completely

dry. Do not sand between staining coats.

D. Sealing or applying the top-coat

The top-coat or sealant for your door is very important and

required for weatherability. It protects the stained door from the

elements and makes the door surface washable. Be sure that the

stain coating is completely dry and then apply a high-quality,

UV stabilized, clear exterior polyurethane coating (satin or low

gloss) – used for any normal exterior wood application.

Note: We recommend that all 6 sides (front and back faces plus

all four edges) be sealed to eliminate moisture absorption. The

bottom of your door panel(s) may contain a factory installed

weather-stripping (sweep) which is sealed prior to installation.

Failure to observe this recommendation may void the warranty.

Step 6: Install Dead Bolt and Strike Plates

Step 8: Caulk Doorway

Figure 26: Screws fasten the latch plate to the door slab.

Install the dead bolt strike plate at the correct location,

per the manufacturer installation detail (Figure 26).

Figures 28 and 29: Caulk the sill crown and the front of the sill.

Caulk all four exterior corners and all around the

brick or siding in the following sequence:

caulk the sill on both latch and hinge sides from the

edge of the

sill crown along the edge where the sill

and jamb or brickmould

meet (Figure 28)

caulk the front sill edge where the sill and

the sub-floor meet (Figure 29)

Step 9A: Adjust Sill

Step 9B: Adjust Sweep

caulk the top corners where the header and jambs

meet, starting at the weather-stripping and working

to the face of the brickmould (Figure 30)

caulk the perimeter where the exterior trim meets

the brick or siding trim (Figure 31)

If the door is center-hinged or has a sidelite, caulk around the

mullions where the mullions contact the sill and header.

Figure 32: Raise or lower the sill by adjusting the sill screws.

Some sills may have covers over the adjusting screws. These covers

must be removed prior to making any adjustments.

Some door units are supplied

with adjustable sills, and these

may be raised or lowered to form

a tight seal with the fixed sweep

on the bottom of the door. This

adjustment requires a screwdriver

with appropriate screw bit. To

increase the height of the sill,

turn screws evenly along the sill

cap. Refer to the “Steps to test

threshold seal”. (Figure 32-A).

Figures 30 and 31: Caulk the jambs and the exterior trim.

Step 7: Insulate

Score shims with a utility knife

and snap the shims along the

score. Trim any excess with the

utility knife. Insulate around the

top and sides of the door unit

in the cavity between the jamb

and the wall studs with fiberglass

blanket insulation (Figure

27). Install the interior and/or

exterior trim around the door.

Figure 27: Insulate between the jambs and the wall studs all around the door.

Critical Point: The use of expandable type foam

is not recommended as it may cause the door

jambs to warp; this may leave the door inoperable

or push the brickmould away from the jamb.

Step 10: Install the Latch and Dead Bolt

Figure 34: The latch and dead bolt are installed per the

hardware manufacturer installation detail.

Steps to test threshold seal

(Figure 32-A)

1. Close door on a piece of paper

placed over the threshold.

2. Pull paper between the sweep

of the door and the threshold.

3. If the threshold is properly

adjusted, you should feel some

tension, but if the paper tears,

the door’s seal is too tight.

If there is no tension on the paper, the door’s seal is too loose.

To properly adjust the threshold seal if it is too tight.

1. Adjust sill cap by turning screws counter-clockwise evenly a 1/2 turn.

2. Repeat seal test. If paper does not slide beneath door

with a feeling of tension, repeat Step 1. Re-test seal.

3. Continue testing threshold until it is properly adjusted.

To properly adjust the threshold seal if it is too loose.

(WARNING: Do not increase height by more then 1/4")

1. Adjust sill cap by turning screws clockwise evenly a 1/2 turn.

2. Repeat seal test. If paper does not slide beneath door

with a feeling of tension, repeat Step 1. Re-test seal.

3. Continue testing threshold until it is properly adjusted.

A. How to start

Doors can be stained either hanging in the opening or removed from

the frame (recommended). Should you remove the door, take care to

protect it from damage. Sidelites will need to be finished vertically.

To remove the door from the frame, use a center punch and hammer.

Strike the hinge pin from the bottom until it pops up (for outswing

units – hinge leaf must be removed from the door). Drive the hinge pin

as far as possible with the punch. Using a pair of pliers, grasp the hinge

pin and, while twisting, pull the pin out. Remove all door hardware.

B. Preparing the door surface

IMPORTANT: Dust, debris and other surface contaminants can

accumulate on the surface of the door. Therefore, to achieve best

results and maximum coating adhesion, wipe/clean all surfaces of

the door panel(s) and sidelite(s) thoroughly with acetone or mineral

spirits. Mask (tape) off all surfaces that will not be stained.

C. Staining the Door

Use a high quality, heavily pigmented, oil-based stain (recommended).

Gel stains can also be used. Before starting, and occasionally throughout

the project, stir the stain until the texture is creamy. We recommend

that before starting, you try staining a small inconspicuous area of the

door to achieve the desired color.

One coat of stain is required with the recommended (per manufacturer’s

instructions) dry time needed between sides. The stain should be applied

in the following order working on one small section of the door at a time.

Finishing Order:

#1 Panels and sticking (moulding profiles)

#2 Vertical center areas (mullions)

#3 Horizontal areas (rails)

#4 Outside vertical areas (stiles)

#5 Edge of door (includes both sides

and top of door)

Factory finished door units do not require additional

field finishing. See maintenance steps for proper care.

Requirements:

Find a well-lit staining location that is dust-free,

well ventilated and within the climate conditions

recommended by the stain/top-coat manufacturer.

You will need the following:

Coatings and accessories:

Mineral spirits or acetone

One pair of rubber gloves

Lint-free rags or cheese cloth (recommended)

Stir sticks

2" wide foam brush

Masking tape

Safety razor blades

Stain

–

High-quality, opaque (non-

transparent), heavily pigmented,

oil-based stain (recommended)

–

Gel stains can also be used

–

Semi-transparent stains are not recommended

High-quality, exterior grade, UV stabilized

polyurethane sealant (satin or low gloss)

2-1/2" wide china bristle brush

Tools:

Hammer

Center punch

Screwdriver with arrangement of screw bits

Pliers

Safety glasses

Please read and understand the entire staining

procedure before attempting to finish the door. Be

sure to follow the (stain and top-coat) manufacturers

detailed application instructions on the product label.

1. Stir top coat thoroughly using smooth strokes, avoid creating

bubbles and do not shake the top coat container.

2. Do not overload the brush. Dip the end of the brush

into the coating and gently slide the flat side of the brush

against the edge of the container to remove the excess.

Apply with even gentle strokes. Press hard enough to flex the bristles

just a little and then pull the brush gently along the door’s surface.

4. As you apply the sealant, pull the brush quickly along the area

two or three times lightly to even out the brush strokes.

5. Allow the first coat to dry completely (follow manufacturer’s

recommendations) and apply at least one more coat using

the same steps as above. A minimum of two coats is required

for complete protection and the door should be resealed

annually to ensure lasting protection of the finish.

6. After both sides of the door have been top-coated

(twice) and are completely dry, remove the paper and

tape from the glass and protected surfaces.

7. Clean the glass with window cleaner and remove any

finishing materials from the glass with a safety razor.

8. Replace door back into frame.

Maintenance

1. In the event that the door is scratched after finishing, the damaged

area can be lightly sanded using 400-grit sandpaper (do not over-

sand the surface). Follow the staining and top-coat procedures.

2. Dirt and watermarks can build up on the surface of your finished door

over time. Extend the life of the stain and top-coat by cleaning the door

several times a year. Clean with warm soapy water, rinse and towel dry.

3. A minimum of two coats of top-coat are initially required

for complete protection. The door system should be resealed

every 1 to 7 years depending upon weather exposure.

Step 11: How to Paint Exterior Doors

Factory finished door units do not require any additional field finishing.

Requirements:

Find a well-lit finishing location that is dust-free, well

ventilated and within the climate conditions recommended

by the coating manufacturer. Recommended temperature

should be between 50˚ – 90˚F degrees fahrenheit.

You will need the following:

Coatings and accessories:

Mineral spirits or acetone

Soapy water (mild detergent in warm water)

One pair of rubber gloves

Stir sticks

Masking tape

Safety razor blades

220-grit sandpaper

Paint

– High-quality, oil-base or 100% acrylic water-

based latex paint of desired color

– Lacquer paints are not recommended

2-1/2" wide brush appropriate for type of paint (A natural

bristle brush should be used with oil-based paint and a

synthetic bristle brush should be used with latex paint.)

Tools:

Hammer

Center punch

Phillips screwdriver

Pliers

Safety glasses

Air-less sprayer (optional)

Note: Painting instructions specifically refer to the door and sidelite panels. Oil-

based paint should not be used on wood frame components (jambs & brickmould).

Please read and understand the entire painting procedures

before attempting to finish the door. Be sure to follow the paint

manufacturer’s detailed application instructions on the product label.

A. How to start

Doors can be painted either hanging in the opening or removed from the

frame (recommended). Should you remove the door, take care to protect

it from damage. Sidelites will need to be finished vertically. To remove

the door from the frame, use a center punch and hammer. Strike the

hinge pin from the bottom until it pops up (for outswing & self closing

units – hinge leaf must be removed from the door). Drive the hinge pin

as far as possible with the punch. Using a pair of pliers, grasp the hinge

pin and, while twisting, pull the pin out. Remove all door hardware.

B. Preparing the door surface

IMPORTANT: For adequate paint adhesion the door surface

must be free of dust, debris and other surface contaminants.

Finishing Order:

For woodgrain textured door

finishing with brush.

#1 Panels and sticking

(moulding profiles)

#2 Vertical center areas

(mullions)

#3 Horizontal areas

(rails)

#4 Outside vertical areas

(stiles)

#5 Edges of door

(includes both sides

and top of door)

Finishing with Spray Applicator:

Follow the manufacturer’s instructions for thinning the paint; (i.e. thin

latex paint with water or oil-based with solvent for better atomization

and spraying results). Strain paint before filling the spray pot.

The door can be painted in horizontal (recommended) or

vertical position; however, the paint should be applied in

continuous strokes extending six inches past the edges of the

door. This will ensure uniformity across the entire surface of the

door. Multiple light coats are better than one heavy coat.

Avoid runs as a result of over-spraying.

Note: We recommend that all 6 sides (front and back faces plus all four

edges) be sealed to eliminate moisture absorption. The bottom of your

door panel(s) may contain a factory installed weather-stripping (sweep)

which is sealed prior to installation. Failure to observe this

recommendation may void the warranty.

Drying:

IMPORTANT: Let the paint dry completely, following the

manufacturer’s recommended drying time before handling the

painted surface or applying a second coat. If possible, allow the

door to dry in a horizontal position to minimize paint runs. High

humidity and/or low temperatures may extend your drying time.

Warning: Foam-filled doors painted with dark colors or with attached

storm doors, may become very hot to the touch in direct sunlight.

Do not paint the weather strip and do not close door until paint is

dry (see paint manufacturer’s specifications on minimum drying time).

To maintain product warranty: Paint the door, frame,

header and brickmould within 45 days of installation.

Maintenance:

1. In the event that the door is scratched after finishing, the

damaged area can be lightly sanded using 400-grit sandpaper

(do not over-sand the surface). Follow the finishing procedures

on the inside of this brochure.

2. Dirt and watermarks can build up on the surface of your finished

door over time. Extend the life of the paint by cleaning the door a

few times a year. Clean with warm soapy water, rinse and towel dry.

3. Repainting every 1 to 7 years will be required, depending

upon weather exposure.

Step 11: How to Paint Exterior Doors

Warranty

Warranties are available for most products. Please check with your dealer

or distributor for current warranty terms and conditions.

Figure 33: U-channel sweeps are adjusted to form a tight seal with the sill.

Some door units are supplied with a U-channel adjustable sweep and

these may be raised or lowered to form a tight seal with the fixed sill.

To adjust the sweep, loosen the screws that hold the sweep in place and

lower the sweep far enough to create an airtight seal with the sill. Once

the sweep is positioned properly, tighten the screws by hand, taking

care not to over-tighten (Figure 33).

Step 11: How to Stain Woodgrain Textured Fiberglass Doors

Step 11: How to Paint Exterior Doors

Step 11: How to Stain Woodgrain Textured Fiberglass Doors

If it becomes apparent that there is some trouble with the operation

of the unit, the first thing to check is the installation of the unit

into the rough opening. Check to insure that 1/8" gap across

the top edge of door panel and frame holds true for the entire

width of the door opening AND that weather-stripping is evenly

compressed the entire height of the door opening. Secondly,

check that the two jambs are correctly aligned with each other and

that incorrect nailing on shims have not twisted the jambs.

Check all Critical Points to confirm that unit was

installed correctly in proper rough opening.

MIC-12713 Rev. A 02-02-17

Note: Units intended for installation in high velocity

windstorm region requires specific grade of latching hardware.

Steel doors should be wiped clean with a solvent such as acetone or

mineral spirits. Allow the cleaning solvent to dry completely – until there

is no residual odor. Once wiped clean, the door must be lightly sanded

with a 220-grit sandpaper. After sanding, the door must be washed

with a mild detergent in warm soapy water, rinsed and then dried.

Fiberglass doors should be wiped clean with a solvent such as acetone

or mineral spirits. Allow the cleaning solvent to dry completely – until

there is no residual odor. Next, the door must be washed with a

mild detergent in warm soapy water, rinsed and then dried.

Mask (tape) off all surfaces that will not be painted including all glass.

C. Painting the Door

Use exterior, high quality, oil-based or 100% acrylic water-based

latex paint of desired color. High quality interior paint can be

used on the interior surface of the door only. Lacquer paints are

not recommended. Follow the manufacturer’s instructions for

paint application by using either a brush or a handheld sprayer.

Painting:

Put on gloves, safety glasses, and prepare your materials. Before

starting, and occasionally throughout the project, stir the paint using

smooth strokes until the texture is creamy – avoid creating bubbles.

Finishing with Brush Application:

Dip the brush into the paint, then use the rim of the container to

release any excess paint. Apply paint as evenly as possible while still

wet. Brush strokes should follow the grain direction of the selected area.

Start working on the panels and sticking (moulding profiles), then the

vertical center mullion, next the horizontal rails, then the vertical stiles,

and finally, the outside edges (stiles and top rail, see figure 1 for details).

Doors that are outswing or have adjustable surface mounted sweeps

will need to have the sweep removed and the bottom rail painted.

1. At the ends of the sill, apply

a bead of caulk where the cap

and jamb/mullion meet.

2. Apply the corner pad with the

thick side towards the weather-

strip and the thin side even with

the edge of the jamb/mullion. Be

sure the pad is seated in the caulk.

Proper installation of the corner seals (Foam Pads) is critical to the

performance of your new door system. Please use these photos along with

Step #12 to make sure the corner seals are properly installed.

Step 12: Corner Seal (Foam Pad) Installation

Trouble Shooting