Measurement Guide

ManualsBrandsMasonite ManualsBarn Doors36 in. x 84 in. Lincoln Park Primed White Composite Interior Barn Door Sliding Door Hardware Kit

COMMON COMPONENTS

Stopper

Allen

wrench

Strap

Roller

Standard

1-3/16" Strap

Bolts

Anti-jump

Block

#8 (4.2mm x

25mm)

Floor Screws

1/4 (6mm)

Floor Anchor

Internal

Floor-Mounted

Door Guide

Wall-Mounted

Door Guide

Optional

Floor-Mounted

Door Guide

Optional

# 10 x 2-1/2

Wood Screws

For mounting

wood block for

drywall installation

TRACK COMPONENTS

78 -3/4"

Track

(

holes)

Wall

Spacer

5/16" (8mm x 60mm) Carriage Bolt

and 5/16" (8mm x 25mm) Anchor

(Pre-mounted to Carriage Bolt)

For concrete wall

installation only

3/8"

Washer

5/16"

(8mm x 90mm)

Track Mount

Lag Bolts

For drywall

installation with

wood blocking

TOOLS REQUIRED

3/4" (19 mm)

1/4"

(6.3 mm)

3/8"

(10 mm)

Center to stile

or minimum

of 2" (51 mm)

(51 mm)

Tape Measure Pencil Phillips Screwdriver Cordless Drill Drill bit*

(1/8", 1/4", 5/16"

and 3/16")

Wrench

(13mm, 16mm,

and 17mm)

Stud Finder Level Speed Square Hammer Step Ladder

* Depending on model and mounting application

NOTE: if installing in concrete, masonry bits will be needed

Look for alert symbol to identify

important objectives in step.

Barn Door

Installation Guide

FOR

1-800-663-DOOR masonite.com

IMPORTANT

BEFORE YOU BEGIN

Read instructions fully before

starting the installation of your

barn door. Not following the

installation instructions can

cause the unit to work in an

unsafe manner and cause injury.

The barn door kit has been

designed to work as a total

system. Any modification to the

door or the hardware will void

the warranty and may cause

the unit to work improperly.

The weight of the barn

door requires 2 people

during installation.

Always wear appropriate

personal protection

equipment when using tools

and follow manufacturer's

operating instructions.

When installing directly into

a non-concrete wall, do not

attempt to install the track

solely to the drywall or any

wall surface as this may not

support the weight of the

track and mounted door.

The track must be installed onto

a piece of solid wood blocking

using mounting screws (included

in some complete kits).

Ensure the solid wood blocking

is secured into

the structural surface.

Use a stud finder where

necessary to locate studs

and secure safely.

Warranty available on

Masonite.com.

ble Wrench

STRAP KITS

Summary of content (7 pages)

PAGE 1
Barn Door Installation Guide FOR V STRAP KITS COMMON COMPONENTS IMPORTANT BEFORE YOU BEGIN Read instructions fully before 2x 1x Stopper Allen 2x V Strap Roller wrench 4x 2x 2x Standard 1-3/16" Strap Bolts Anti-jump Block #8 (4.2mm x 25mm) Floor Screws starting the installation of your barn door. Not following the installation instructions can cause the unit to work in an unsafe manner and cause injury.
PAGE 2
Barn Door Installation Guide FOR V STRAP KITS HARDWARE MATCH UP GUIDE # 10 x 2-1/2" Wood Screws Refer to the following full scale hardware drawings to quickly match up the hardware. 1/4" 5/16" (8mm x 60mm) (6.3 mm) Carriage 1/4" Bolt (6.3 mm) Standard 1-3/16" Strap Bolts 3/4" (19 mm) 3/4" (19 mm) 5/16" (8mm x 90mm) Track Mount Lag Bolt 1 DOOR PREPARATION STRAP INSTALLATION Tape Measure Speed Square FIGURE 1.
PAGE 3
Barn Door Installation Guide FOR V STRAP KITS 3 MARKING TRACK LOCATION FOR CONCRETE WALL INSTALLATION Speed Square When installing with a standard 80" height opening, the top trim will need to be removed, and the top of the side trim cut horizontally along the height of the opening. (NOT SHOWN) 4 CONCRETE WALL PREPARATION Remove metal anchors from bolts and install into holes using a hammer. (FIGURE 5) INSTALLATION TIP: locate and temporarily install track with one end bolt without spacer.
PAGE 4
FOR V STRAP KITS 3” from opening 6 DRY WALL PREPARATION Speed Square 3/8 (9.5 mm), 3/8” (9.5 1/2” (12.7 mm)mm), gap under the 1/2” (12.7 mm) door 3/8 (9.5 mm), gap under 1/2” (12.7 mm) the gap under the door door 3” from opening 3” from opening 3” from opening FIGURE 6. Locate the position of track Using a ladder, tape measure and speed square, find the center line position of the track by adding 1-3/4" to the door height and measuring up from the floor. Mark with a pencil.
PAGE 5
FOR V STRAP KITS 9 MOUNTING TRACK TO BOARD Door height + 1 Door height + 1 3/4” Barn Door Installation Guide Solid wood blocking Solid wood blocking Minimum 2” (51 mm) Minimum 2” (51 mm) 3/8” (9.5 mm), 1/2” (12.7 mm) gap under the 3/8” (9.5 mm), door 1/2” (12.7 mm) gap under the door FIGURE 9. Drilling for track mounting lag bolts Drill 1/4" dia pilot holes for track mounting lag bolts into board at marked locations from Step 7.
PAGE 6
Barn Door Installation Guide FOR V STRAP KITS 13 FLOOR-MOUNTED DOOR GUIDE INSTALLATION Used for standard doors that are grooved in the bottom of the panel for the guide. With the door hanging straight, position the floormount door guide inside groove in the bottom of the door. Slide the door side to side to ensure the guide is properly placed. Mark location of the guide. FIGURE 12.
PAGE 7
x2 Floor-mounted bottom guides x4 #8 5/8" pan head philips screws Barn Door Installation Guide FOR V STRAP KITS 16 FINAL CHECK OF STOPPERS AND ANTI-JUMP BLOCKS FIGURE 15. Securing stoppers and anti-jump blocks Check to see that stoppers are properly located and tightened in place. Also check to see that anti-jump blocks are rotated correctly and tightened. 1/4" (8 mm) Drill depth 1 3/16" (30 mm) 1/8" (3 1/2 mm) 1-800-663-DOOR masonite.com ©2022 Masonite International Corporation.