Operating instructions

ManualsBrandsMasport ManualsKitchen AppliancesF28-LP

FOR YOUR SAFETY

What to do if you smell gas:

! Do not try to light any ap-

pliance

! Do not touch any electri-

cal switch: do not use any

phone in your building.

! Immediately call your gas

supplier from a neigh-

bour's phone. Follow the

gas supplier's instruc-

tions.

! If you cannot reach your

gas supplier, call the fire

department.

WARNING:

Improper installation, adjustment, altera-

tion, service or maintenance can cause

injury or property damage. Refer to this

manual. For assistance or additional infor-

mation consult an authorized installer, serv-

ice agency or the gas supplier.

FOR YOUR SAFETY

Do not store or use gasoline or other flam-

mable vapours and liquids in the vicinity of

this or any other appliance.

Installation and service must be performed

by an authorized installer, service agency or

the gas supplier.

PLEASE KEEP THESE INSTRUCTIONS

FOR FUTURE REFERENCE

Owners &

Installation

Manual

LISTINGS AND CODE

APPROVALS

These gas appliances have been

tested in accordance with AG

103, NZS 5262 and have been

certified by the Australian Gas

Association for installation and

operation as described in these

Installation and Operating

Instructions.

Your unit should be serviced

annually by an authorised

service person.

Models: F43-NG Natural Gas

F43-LP Propane

F28-NG Natural Gas

F28-LP Propane

02/01/01

Geneva /Ultimate

Head Office - Australia

54 Boundary Rd. Braeside

P.O. Box 553

Mordialloc 3195

Ph. (03) 9586-7777

Fax. (03) 9586-2980

Head Office - New Zealand

1-37 Mt Wellington Hwy.Panmure,

P.O. Box 14349

Auckland 6.

Ph. (9) 570-9009

Fax. (9) 527-1294

908-061

(Australia) (New Zealand)

Summary of content (26 pages)

PAGE 1
Owners & Installation Geneva /Ultimate Manual (Australia) (New Zealand) Models: F43-NG F43-LP F28-NG F28-LP PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE WARNING: Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to this manual. For assistance or additional information consult an authorized installer, service agency or the gas supplier.
PAGE 2
To the New Owner: Congratulations! You are the owner of a state-of-the-art Gas Heater by MASPORT. The Masport Gas Series of hand crafted appliances has been designed to provide you with all the warmth and charm of a woodstove, at the flick of a switch. The models F43-NG, F43-LP, F28NG, and F28-LP of this series has been approved by Australian Gas Association for both safety and efficiency.
PAGE 3
TABLE OF CONTENTS Page Safety Label Page Optional Remote Control Installation ....... 14 Final Check .............................................. 14 Data Plate .................................................. 4 Operating Instructions Installation General Installation Information ................. 5 Installation Checklist .................................... 6 Draft Diverter ................................................ 6 Flueing .......................................................
PAGE 4
SAFETY LABEL This is a copy of the label that accompanies each Masport F43 Freestanding Gas Heater. We have printed a copy of the contents here for your review. DATA BADGE NOTE: Masport units are constantly being improved. Check the label on the unit and if there is a difference, the label on the unit is the correct one.
PAGE 5
INSTALLATION BEFORE YOU START GENERAL INFORMATION This installation must conform with local codes or, in the absence of local codes, with AG 601 (Austrlia) NZS (New Zealand) THIS APPLIANCE SHOULD BE INSTALLED, REPAIRED, INSPECTED BEFORE USE AND AT LEAST ANNUALLY BY AN AUTHORISED SERVICE PERSON. MORE FREQUENT CLEANING MAY BE REQUIRED, DUE TO EXCESSIVE LINT FROM CARPETING, ETC. IT IS IMPERATIVE THAT CONTROL COMPARTMENT, BURNERS AND CIRCULATING AIR PASSAGEWAYS OF THE APPLIANCE BE KEPT CLEAN.
PAGE 6
INSTALLATION signs of deterioration. explained to customer. 6) Any safety glass removed for servicing must be replaced prior to operating the appliance. This includes: a) Clocking the appliance (see data badge). 7) To prevent injury, do not allow anyone who is unfamiliar with the operation to use the fireplace. b) Adjusting the primary air, if required, to ensure that the flame does not carbon. See page18. Wear gloves and safety glasses for protection while doing required maintenance.
PAGE 7
INSTALLATION CLEARANCES TO COMBUSTIBLES Note: Not intended for fireplace insert. The clearances listed below are MINIMUM distances. Measure the clearance to both the appliance and the chimney connector. (The farthest distance is correct if the two clearances do not coincide.) For example, if the appliance is set as indicated in one of the figures but the connector is too close, move the stove until the correct clearance to the connector is obtained.
PAGE 8
INSTALLATION GAS CONNECTION GAS PIPE PRESSURE TESTING The gas line can be rigid pipe, or to make installation easier, use a listed flexible connector if allowed by local codes. Copper may also be used if approved by local codes. The appliance must be isolated from the gas supply piping system by closing its individual manual shut-off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig. (3.45 kpa).
PAGE 9
INSTALLATION LOG INSTALLATION - F43 WARNING: Dangerous operating conditions may occur if these logs are not positioned in their approved locations. Read the instructions below carefully and refer to the diagrams. If logs are broken do not use the unit until they are replaced. Broken logs can interfere with the pilot and burner operation. The gas log kit contains the following: a) b) c) d) Front Right Log Front Left Log Rear log Embers Diagram 2 1) Remove the logs from the box and carefully unwrap them.
PAGE 10
INSTALLATION LOG INSTALLATION - F28 4) Place the right front log, carefully sliding it down onto the right pins of the front burner. See diagram 3. WARNING: Dangerous operating conditions may occur if these logs are not positioned in their approved locations. Read the instructions below carefully and refer to the diagrams. If logs are broken do not use the unit until they are replaced. Broken logs can interfere with the pilot and burner operation.
PAGE 11
INSTALLATION FRONT DOOR INSTALLATION 1) Open the two side panels. 2) Slide the door onto the two hinge pins making sure the two pieces are flush together. See diagram 1. Diagram 2 - F43 Diagram 1 3) Close the door. The latch plate must be centered around the alignment pin. See diagram 2. If the latch plate interferes with the corner of the stove you may want to angle the plate slightly so the door closes easier. 4) The latches should already be at the proper setting.
PAGE 12
INSTALLATION TEST FOR FLUE SPILLAGE A "spillage" test must be made before the installed unit is left with the customer. Follow the procedure below: 1) Start all exhaust fans in the home and any other gas appliances. Then close all doors and windows. 2) Light the unit and set controls to maximum. 3) After five minutes, test that there is a "pull" on the flue by placing a smoke match, cigarette or similar device which gives off smoke, on the edge of the draft diverter. See diagrams.
PAGE 13
INSTALLATION WIRING DIAGRAM - F43 WIRING DIAGRAM - F28 Masport F43/F28 Freestanding Gas Heater 13
PAGE 14
INSTALLATION OPTIONAL WALL THERMOSTAT INSTALLATION OPTIONAL REMOTE CONTROL INSTALLATION A wall thermostat may be installed if desired. Use chart below to determine thermostat wire length. Use the Masport Remote Control Kit (Part # 910-358/P) approved for this unit. Use of other systems may void your warranty. Thermostat Wire Table Recommended Maximum Lead Length (Two-Wire) When Using Wall Thermostat (CP-2 System) Wire Size 14 16 18 20 22 GA. GA. GA. GA. GA.
PAGE 15
OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS 5) Push in PILOT knob all the way in and hold. Immediately push IGNITOR button until pilot lights. Continue to hold the PILOT knob in for approximately one minute, then release the PILOT knob. The pilot flame should continue to burn. If the pilot does not remain lit, repeat operation allowing a longer period before releasing PILOT knob. 6) Turn PILOT knob counter clockwise to on. 7) Use the ON/OFF switch to turn on the burner.
PAGE 16
OPERATING INSTRUCTIONS Copy of the Lighting Plate instructions FOR YOUR SAFETY READ BEFORE LIGHTING This appliance must be installed in accordance with local codes, if any; if not, follow the current CAN1-B149/ANSI Z 223.1 (Australia: AG601, New Zealand: NZS 5261) WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.
PAGE 17
OPERATING INSTRUCTIONS AUTOMATIC CONVECTION FAN OPERATION The fan operates automatically - turn the knob in the pedestal base to High or Low speed. The fan will turn on as the stove comes up to operating temperature. After the unit has been turned off and cools to below a useful heat output range the fan will shut off automatically. PILOT ADJUSTMENT Periodically check the pilot flames.
PAGE 18
OPERATING INSTRUCTIONS AERATION ADJUSTMENT The burner aeration is factory set but may need adjusting due to either the local gas supply or altitude. F43-NG Natural Gas: 1/4" open F43-LP Propane: Fully open (rear) and fully open (front) F28-NG Natural Gas 1/8" open F28-LP Propane 3/8" open The aeration adjustment gears are located on the right side of the burner box and can be accessed from the side or from the front when the louvers are removed.
PAGE 19
MAINTENANCE IMPORTANT MAINTENANCE INSTRUCTIONS SERVICE ANNUALLY ONLY BY AN AUTHORISED PERSON 1) Clean the burner and control compartment of lint and house dust by brushing and vacuuming at least once a year. When cleaning the logs, use a soft clean brush as the logs are fragile and easily damaged. During the annual service the burners should be removed from the burner tray and cleaned. Replace logs and embers as per instructions on pages 9 and 10. 2) 3) 4) ANCE.
PAGE 20
MAINTENANCE Installing Glass: GLASS REPLACEMENT Your Masport heater is supplied with high temperature, 5mm Neoceram silica coated ceramic glass that will withstand the highest heat that your unit will produce. In the event that you break your glass, purchase your replacement from an authorized Masport dealer only, and follow the step-by-step instructions for replacement. 1) Install both center and side glass onto aluminium extrusions as per diagram. 2) Place glass assembly into door frame.
PAGE 21
MAINTENANCE FAN MAINTENANCE If the fan requires maintenance or replacement, access to the fan is through the access panel on the rear wall of the firebox. Note: The unit MUST NOT be operated without the fan access panel securely in place and correctly sealed. IMPORTANT:These fans collect a lot of dust from within your home. Ensure you maintain these fan motors on a regular basis by vacuuming out the fan squirrel cages, around the motor, and around the grills on the back of the stove.
PAGE 22
MAINTENANCE To remove F28 fan: 1) Unplug or disconnect power source to stove. 2) Remove all logs and the rear log support, then remove the 10 screws holding the access panel in place, see Diagram 1. (Fan can also be accessed from the right side by opening the right side door. See Diagram 2). 3) Unclip the black, red and white wires from the fan motor. 4) Lift fan off of the 2 pins, tip back and pull through firebox opening.
PAGE 23
MAINTENANCE REMOVING VALVE 2) Undo the six screws holding the control panel in place. 3) Disconnect all wires from the back of the panel and then remove panel. You should lay the panel on a soft cloth so it doesn't get marked up. See diagram below. 4) Remove the two outside frame pieces by removing two screws per side. See diagram below. If your valve requires maintenance or replacement, follow these instructions: NOTE: Always shut off the gas supply before removing the valve.
PAGE 24
MAINTENANCE 5) Carefully remove the logs, embers and rockwool. 6) At this point you should disconnect the gas at the valve. 7) Remove the burner by removing the four 1/4" hex head screws. See diagram below. 8) Remove eight 1/4" hex head screws holding the burner tray assembly in place. 9) Carefully lift the burner tray assembly out. Note: Use a magnetic type screwdriver. F43 Burner 10) To replace the burner tray assembly, simply reverse these instructions.
PAGE 25
MAINTENANCE TROUBLESHOOTING THE GAS CONTROL SYSTEM Note: Before troubleshooting the gas control system, be sure external gas shut off is in the "on" position. • WARNING • BEFORE DOING ANY GAS CONTROL SERVICE WORK, REMOVE THE GLASS FRONT. TROUBLESHOOTING GUIDE PROBLEM POSSIBLE CAUSES CORRECTIVE ACTION Spark igniter will not Piezo wire loose light pilot. Defective Piezo igniter. Piezo wire grounding out. Electrode is grounding out and/or wrong location. • Check for spark at electrode and pilot.
PAGE 26
WARRANTY THE MASPORT EXPRESS WARRANTY All new Masport Gas appliances are warranted, subject to the following conditions, to be free from defects in material or workmanship under normal use. The Express Warranty on all parts, including firebox components but excluding fans, flues and flue accessories is two years from date of original purchase as well as labour costs involved in the repair or replacement.