Operating instructions

ManualsBrandsMasport ManualsHome building and DecorNew York

Model: I43-NG Natural Gas

I43-LP Propane

Vienns

Owners &

Installation

PLEASE KEEP THESE INSTRUCTIONS

FOR FUTURE REFERENCE

Manual

05/11/01

Head Office - Australia

54 Boundary Rd. Braeside

P.O. Box 553

Mordialloc 3195

Ph. (03) 9586-7777

Fax. (03) 9586-2980

Head Office - New Zealand

1-37 Mt Wellington Hwy.Panmure,

P.O. Box 14349

Auckland 6.

Ph. (9) 570-9009

Fax. (9) 527-1294

LISTINGS AND CODE

APPROVALS

Thesegasapplianceshavebeen

tested in accordance with AG

103, NZS 5262 and have been

certified by the Australian Gas

Association for installation and

operation as described in these

Installation and Operating

Instructions.

Your unit should be serviced

annually by an authorised

service person.

908-059

FOR YOUR SAFETY

What to do if you smell gas:

! Do not try to light any ap-

pliance

! Do not touch any electri-

cal switch: do not use any

phone in your building.

! Immediately call your gas

supplier from a neigh-

bour's phone. Follow the

gas supplier's instruc-

tions.

! If you cannot reach your

gas supplier, call the fire

department.

WARNING:

Improper installation, adjustment, altera-

tion, service or maintenance can cause

injury or property damage. Refer to this

manual. For assistance or additional infor-

mation consult an authorised installer, serv-

ice agency or the gas supplier.

FOR YOUR SAFETY

Do not store or use gasoline or other flam-

mable vapours and liquids in the vicinity of

this or any other appliance.

Installation and service must be performed

by an authorised installer, service agency or

the gas supplier.

New York /Ultimate

(Australia) (New Zealand)

Summary of content (23 pages)

PAGE 1
Vienns Manual Owners & Installation New York /Ultimate (Australia) (New Zealand) Model: CODE These gas appliances have been tested in accordance with AG 103, NZS 5262 and have been certified by the Australian Gas Association for installation and operation as described in these Installation and Operating Instructions. Your unit should be serviced annually by an authorised service person.
PAGE 2
MASPORT GAS INBUILT FIREPLACE TO THE NEW OWNER Congratulations! You are the owner of a state-of-the-art Gas Inbuilt Fireplace by MASPORT. The Masport Gas Fireplace Series of hand crafted appliances has been designed to provide you with all the warmth and charm of a fireplace, at the flick of a switch. The models I43-NG and I43-LP of this series have been approved by Warnock Hersey for both safety and efficiency.
PAGE 3
TABLE OF CONTENTS MASPORT GAS INBUILT FIREPLACE Page Page SAFETY LABEL OPERATING INSTRUCTIONS Safety Labels .......................................... 4 INSTALLATION REQUIREMENTS For your safety ................................................ Gas Pipe Testing ............................................ Specifications .................................................. Before You Start ............................................. Installation Checklist .......................................
PAGE 4
DATA BADGE This is a copy of the label that accompanies each Masport Gas Inbuilt. We have printed a copy of the contents here for your review. The safety label is located on the right side door panel. DATA BADGE NOTE: Masport units are constantly being improved. Check the label on the unit and if there is a difference, the label on the unit is the correct one.
PAGE 5
INSTALLATION REQUIREMENTS IMPORTANT: SAVE THESE INSTRUCTIONS The Masport I43 Gas Fireplace must be installed in accordance with these instructions. Carefully read all the instructions in this manual first. Consult the "authority having jurisdiction" to determine the need for a permit prior to starting the installation. Note: Failure to follow these instructions could cause a malfunction of the heater which could result in death, serious bodily injury, and/or property damage.
PAGE 6
INSTALLATION REQUIREMENTS INSTALLATION CHECKLIST The Masport Gas Inbuilt is installed as listed below. Note: This unit is equipped with a heat sensor thermodisc which will prevent the fan from operating until the unit reaches the correct temperature. 1) Unit Location - check Clearances to Combustibles on page 7. CLEARANCES 2) Make the gas connections and electrical connection for fan and flue spill switch. See page 8.
PAGE 7
INSTALLATION REQUIREMENTS Clearances to Combustibles B E G F C I Sides Ceiling Mantel From Unit A 7.5" / 190 mm B 35" / 890 mm C(My) 11 / 280 mm Sides Ceiling Mantel From Surround D 2" / 50 mm E 25.5" / 650 mm F 3" / 75 mm Min. Alcove Width Mantel Depth J 48" / 1120 mm G(Mx) 7.5" / 190 mm Facing (Mantel Leg) Side* Top K L 1" / 25 mm 1" / 25 mm A D H J *Max. width of 25mm at 25mm from surround, calculate depth at 45o as shown in the diagram.
PAGE 8
INSTALLATION INSTRUCTIONS System Data For 0 to 610 metres altitude* Burner Inlet Orifice Sizes: Natural Gas Propane Rear Burner n/a #54(1.4mm) Front Burner #31(3.0mm) #56(1.15mm) Input Rating - Natural Gas - Propane 40 mj 39 mj Supply Pressure: Natural Gas min. Propane min. 1.13 kPa 2.75 kPa Manifold Pressure Natural Gas Propane .85 kPa 2.55 kPa 1) If the appliance is to be installed into an existing chimney system, thoroughly clean the masonry fireplace and have the chimney swept.
PAGE 9
INSTALLATION REQUIREMENTS DRAFT DIVERTER CONNECTION 1) Attach the flue to the flue collar on the detachable draft diverter. The flue collar of the appliance will fit inside a standard 100mm flue and may be fastened directly to the flue by sheet metal screw. FLUEING THE APPLIANCE MUST NOT BE CONNECTED TO A CHIMNEY FLUE SERVING A SEPARATE SOLID FUEL BURNING APPLIANCE. This appliance is designed to attach to a 100mm diameter flue or approved aluminum flex liner running the full length of the chimney.
PAGE 10
INSTALLATION INSTRUCTIONS COMBUSTION & VENTILATION AIR AERATION SYSTEM WARNING: This appliance needs fresh air for safe operation and must be installed with provisions for adequate combustion and ventilation air available to the room in which it is to be operating. The burner aeration is factory set but may need adjusting due to either the local gas supply, air supply or altitude.
PAGE 11
INSTALLATION INSTRUCTIONS TEST FOR FLUE SPILLAGE A “spillage” test must be made before the installed unit is left with the customer. Follow the procedure below: 1) Start all exhaust fans in the home and then close all doors and windows in the room. 2) Light the unit and set controls to maximum. Turn fan off. 3) After five minutes, test that there is a “pull” on the flue by placing a smoke match, cigarette or similar device which gives off smoke, in front of the spill tube.
PAGE 12
INSTALLATION INSTRUCTIONS FACEPLATE & TRIM INSTALLATION Hint: Before doing the faceplace installation, leave the inbuilt out approximately 4" so wires may be hooked up easier. 1) Lay the faceplate panels flat, face down on something soft so they don't scratch. 2) Take the top faceplate and align the holes in it with the holes in the side panels. Attach, using the screws provided. See diagram 1.
PAGE 13
INSTALLATION INSTRUCTIONS BRICK PANEL INSTALLATION Diagram 1 1) Unwrap the brick pattern panels from the protective wrapping. 2) Open the door and position the side brick panels into place from the front of the firebox. There are two tabs to the panels in place, on on each side. Carefully bend the tabs down with a screwdriver until panels are held securely in place. Note: Use caution when putting the side panels in as they can easily be scratched by the hard component parts.
PAGE 14
INSTALLATION INSTRUCTIONS DOOR INSTALLATION 1) Open the two side doors. 2) Slide the door onto the two hinge pins making sure the two pieces are flush together. See diagram 1. Diagram 3 Note: The door latch may require adjustment as the door gasket material compresses after a few fires and after glass replacement. Turn the latch to tighten or loosen the latch. OPTIONAL WALL THERMOSTAT Diagram 1 3) Close the door. The latch plate must be centered around the alignment pin. See diagram 2.
PAGE 15
INSTALLATION INSTRUCTIONS OPTIONAL REMOTE CONTROL FINAL CHECK Use the Masport Remote Control Kits approved for this unit. Use of other systems may void your warranty. Before leaving this unit with the customer, the installer must ensure that the appliance is firing correctly. This includes: The remote control kit comes with a hand held transmitter, a receiver and a wall mounting plate. 1) Check operating pressure (see Data Badge for operating pressure settings).
PAGE 16
OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS Before operating this appliance, proceed through the following check list. 1) Read and understand these instructions before operating this appliance. 2) Clean the burner and control compartment of lint and house dust by brushing and vacuuming regularly. At least once a year. 3) Never operate the appliance with any of the glass removed or with the door open. 4) Verify log placement.
PAGE 17
OPERATING INSTRUCTIONS COPY OF THE LIGHTING PLATE INSTRUCTIONS FOR YOUR SAFETY READ BEFORE LIGHTING This appliance must be installed in accordance with local codes, if any; if not, follow the current CAN1-B149/ANSI Z 223.1 (Australia: AG601 / New Zealand: NZS 5261) WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.
PAGE 18
OPERATING INSTRUCTIONS FIRST FIRE The first fire in your heater is part of the paint curing process. To ensure that the paint is properly cured, it is recommended that you burn your fireplace for at least four (4) hours the first time you use it with the fan on. When first operated, the unit will release an odour caused by the curing of the paint, the burning off of any oils remaining from manufacturing. Smoke detectors in the house may go off at this time.
PAGE 19
MAINTENANCE IMPORTANT MAINTENANCE INSTRUCTIONS SERVICE ANNUALLY ONLY BY AN AUTHORISED PERSON 1) Clean the burner and control compartment of lint and house dust by brushing and vacuuming at least once a year. When cleaning the logs, use a soft clean brush as the logs are fragile and easily damaged. 7) Periodically check the pilot flames.
PAGE 20
MAINTENANCE LOG REPLACEMENT GLASS REPLACEMENT The unit should never be used with broken logs. Turn off the gas valve and allow the unit to cool before opening door to carefully remove the logs. The pilot light generates enough heat to burn someone. If for any reason a log should need replacement, you must use the proper replacement log. The position of these logs must be as shown in the diagram under Log Installation.
PAGE 21
MAINTENANCE Installing Glass 1) Install both center and side glass onto extrusions as per diagram. To remove fan: 1) Unplug or disconnect power source to stove. 2) Remove all logs and the rear log support, then remove the 6 screws holding the access panel in place. 3) Disconnect white wire from fan to power cord. 4) Disconnect black wire from molex plug to thermodisc. 5) Unplug wire harness on left rear side panel (from inside the stove). 2) Place glass assembly into door frame.
PAGE 22
SERVICE TROUBLESHOOTING THE GAS CONTROL SYSTEM Note: Before troubleshooting the gas control system, be sure external gas shut off is in the "on" position. WARNING: BEFORE DOING ANY GAS CONTROL SERVICE WORK, REMOVE THE GLASS FRONT. TROUBLESHOOTING GUIDE PROBLEM POSSIBLE CAUSES CORRECTIVE ACTION Spark igniter will not Piezo wire loose light pilot. Defective Piezo igniter. Piezo wire grounding out. Electrode is grounding out and/or wrong location. • Check for spark at electrode and pilot.
PAGE 23
WARRANTY THE MASPORT EXPRESS WARRANTY All new Masport Gas appliances are warranted, subject to the following conditions, to be free from defects in material or workmanship under normal use. The Express Warranty on all parts, including firebox components but excluding fans, flues and flue accessories is two years from date of original purchase as well as labour costs involved in the repair or replacement.