Use and Care Manual

4
www.masterappliance.com
4. To turn heat gun
off after use, move
switch to “I” position.
Run on cold for
approximately three
minutes. This will
allow the heat gun to cool down and the
nozzle to become cool to the touch.
5. Move switch to
"O" position.
1. Plug heat gun into properly rated outlet.
2. Move rocker switch to “II” position. (VT
Models, turn heat control to desired
heat setting). Heat
gun will come up
to full operating
temperature in
approximately two
minutes.
3. Adjustable stand
is provided to allow
nozzle to be rotated
from almost horizontal
to vertical position.
Important Safety Instructions
• Cleanupallremovedpaintanddust
by wet mopping the oors. Use a wet
cloth to clean all walls, sills and any other
surface where paint or dust is clinging. DO
NOTSWEEP,DRYDUSTORVACUUM.
Use a high phosphate detergent or
trisodium phosphate (TSP) to wash and
mop areas.
• Attheendofeachworksessionput
the paint chips and debris in a double
CLEANING
TO OPERATE HEAT GUN
Unplug heat gun before cleaning. To clean
outside of tool, use only a mild soap and
damp cloth. Do not use other cleaning
agents, turpentine, gasoline, lacquer or paint
thinner, or other solvents that may contain
chemicals which are harmful to plastics and
other insulating materials. Never immerse
tool in a liquid or allow a liquid to enter inside
the tool. Make sure all vents and openings
are free and clear of debris.
allowed to pass into the heat gun and
there must be an outlet of equal size for
the heated air to pass out of the enclosure
also. Total enclosure will cause damage or
possible failure to the heat gun due to the
extreme heat generated.
For typical applications and tips please
consult www.masterappliance.com.
If you have any questions regarding your
specic application or use, feel free to call our
Customer Service Department at
262-633-7791.
NOTICE:Usersshouldindependently
evaluate the suitability of the product for
their application.
NOTICE:TheHG-201D/T,202D/Tand
VT-751D/752Delementisprotectedbya
self-resetting fuse. If the element does
not heat, unplug the unit for several
minutes to reset, then follow operating
instructions to use.
plastic bag, close it with tape or twist ties,
and dispose of properly.
• Removeprotectiveclothingandwork
shoes in the work area to avoid carrying
dust into the rest of the dwelling. Wash
work clothes separately. Wipe shoes off
with a wet rag that is then washed with
the work clothes. Wash hair and body
thoroughly with soap and water.
-CAUTION-
HIGH TEMPERATURE AT
NOZZLE. RUN ON ‘COLD’
BEFORE TURNING OFF.
-ADVERTENCIA-
ALTA TEMPERATURA EN LA
BOQUILLA. ANTES DE
APAGAR LA HERRAMIENTA.
A LA SORTIE.
DU BEC OPÉRER À ‘COLD’
AVANT DE FERMER
-CAUTION-
HIGH TEMPERATURE AT
NOZZLE. RUN ON ‘COLD’
BEFORE TURNING OFF.
-ADVERTENCIA-
ALTA TEMPERATURA EN LA
BOQUILLA. ANTES DE
APAGAR LA HERRAMIENTA.
A LA SORTIE.
DU BEC OPÉRER À ‘COLD’
AVANT DE FERMER
4
3
2
1
5
6
7
8
9
-CAUTION-
HIGH TEMPERATURE AT
NOZZLE. RUN ON ‘COLD’
BEFORE TURNING OFF.
-ADVERTENCIA-
ALTA TEMPERATURA EN LA
BOQUILLA. ANTES DE
APAGAR LA HERRAMIENTA.
A LA SORTIE.
DU BEC OPÉRER À ‘COLD’
AVANT DE FERMER
 WARNING-ToReduceTheRisk
Of Fire Or Electric Shock, Connect To
GroundedOutlet.DoNotExposeTo
Rain Or Moisture. Store Indoors; Read
Instruction Manual Before Using.
 CAUTION-HIGHTEMPERATURE
ATNOZZLE.RUNONCOLDBEFORE
TURNINGOFF.
NOTICE:Whenheatgunisusedinan
enclosed container, such as a shrink tunnel
or special enclosure, ambient air must be