ASSEMBLY, CARE & USE MANUAL WARNING & SAFETY INFORMATION Manual Code: 9815110001 052112-02SS ELECTRIC PATIO GRILL MODELS 20150112, 20150213, 20150513, 20150613, 20150713 THIS PRODUCT IS FOR OUTDOOR USE ONLY Approximate assembly time : 60 minutes Tool needed for assembly: Phillips Head Screwdriver WARNING WARNING Use only outdoors where it is well ventilated. This manual contains important information necessary for the proper and safe use of this unit.
GENERAL WARNINGS AND SAFETY INFORMATION READ ALL INSTRUCTIONS When using electrical appliances, basic safety precautions should always be followed including the following: • Cannot be operated for more than 3 hours. • Use GFI protected electrical outlet to reduce the risk of electrical shock. • For outdoor use only. Do not operate in an enclosed area. • Unit MUST be on the ground. Do not place unit on tables or counters. Do NOT move unit across uneven surfaces.
GENERAL WARNINGS AND SAFETY INFORMATION • Be careful when removing food from electric grill. All surfaces are HOT and may cause burns. Use protective gloves or long, sturdy cooking tools. • Drip tray is only for the bottom of electric grill. Do not put drip tray on cooking grate this may damage electric grill. • To disconnect, turn control panel “OFF” then remove plug from outlet. • Unplug from outlet when not in use and before cleaning.
GENERAL WARNINGS AND SAFETY INFORMATION • Fatty foods (hamburgers,etc.) can have excess grease and cause flare ups. When cooking fatty foods use a low setting with lid open. • Clean internal base pan before each use. This will cut down on build-up and flare-ups. • Do not expose electric grill to rain. Do not use around water or operate on wet surfaces. This could cause an electric shock leading to injury and death. • Be sure drip tray is clean before each use.
DO NOT RETURN TO RETAILER For Assembly Assistance, Missing or Damaged Parts Call: MASTERBUILT Customer Service at 1-800-489-1581. Please have Model Number and Serial Number available when calling. These numbers are located on silver label on back of unit.
HARDWARE LIST (A) M5 Thumb Screw Qty: 2 (B) M6x35 Phillips Head Screw Qty: 2 (C) 34x25 Flat Washer Qty: 4 (E) M8x55 Phillips Head Screw Qty:2 (F) Bakelite Spacer Qty: 2 (G) M6x13 Phillips Head Screw Qty: 40 (I) M6 Flat Washer Qty: 8 (J) M4 Flat Washer Qty: 5 (K) M8 Flat Washer Qty: 2 (D) M4x40 Phillips Head Screw Qty: 2 (H) M4x12 Phillips Head Screw Qty: 3 (L) M6x8 Phillips Head Screw Qty: 4 PARTS LIST PART NO PART NO REPLACEMENT PART 9915110002 Lid Kit - Blue 9915110016 Rear Left Leg Kit
ASSEMBLY • • • • BEFORE ASSEMBLY READ ALL INSTRUCTIONS CAREFULLY. ASSEMBLE UNIT ON A CLEAN, FLAT SURFACE. TOOL NEEDED: PHILLIPS HEAD SCREWDRIVER UNPACK ALL PARTS AND LAY OUT IN FRONT OF YOU. CHECK TO MAKE SURE ALL PARTS ARE IDENTIFIED AND ACCOUNTED FOR. *Note that the front of the grill is actually the shortest width of the bottom storage shelf (12).
ASSEMBLY 19 STEP 4 Attach bottom shelf (12) to legs (18) using screws (G) with the feet facing away from right side of the shelf as shown. 12 Repeat for wheel legs (19) on left side using screws (G). G SH O FR R T S ON ID T E 18 REMEMBER! The short side of bottom shelf (12) is the front of grill. 14f 13 STEP 5a Locate front panel (14f) [This is the short panel without the serial plate] and one side panel (13) [This is one of the longer panels].
ASSEMBLY STEP 5b Repeat step 4a for leg (19, “FL”). 13 14f G 19 FL 13 18 BR 19 BL 14b STEP 5c Place panel (14b) [the panel with the serial plate] over panels (13) and insert screw (G); into bottom holes.
ASSEMBLY 11 a 13 G G 19 BL 11 b 18 BR 19 FL STEP 6 Insert support (11b) into front leg (18, “FR”) with holes facing inward. Insert other (11a) into back leg (18, “BR”) with holes facing inward. Repeat steps for left side. When all supports are in place screw holes should be facing each other as shown in image. 18 FR STEP 7 Attach seat (22) to supports using screws (G). 22 Repeat step for remaining seat on opposite side.
ASSEMBLY STEP 8 Attach drip tray bracket (8) to grill base (5) using washers (I) and screws (L). 5 Note: Make sure to use screw (L) from the blister pack, and not screw (G) as screw (L) is shorter than (G). L I L I (L) M6x8 Phillips Head Screw (G) M6x13 Phillips Head Screw 8 5 G I STEP 9 Position grill base (5) onto seat (22) as shown. Secure using washers (I) and screws (G). G I 5 22 22 View of grill base (5) positioned on seats (22) from below.
ASSEMBLY STEP 10 Place logo base (28) onto grill base (5). Secure using washers (J) and screws (H). 5 J 28 H 23 5 24 Note: Hinge for grill base is larger than hinge for grill lid. Attach left bottom hinge (24) to grill base (5) using washers (C) and screws (G). [Welded nut on left bottom hinge (24) should be facing right when secured.] C G 11 STEP 11 Repeat step on other side with right bottom hinge (23), washers (C) and screws (G).
ASSEMBLY 25 STEP 12 26 Note: Hinge for grill lid is smaller than hinge for grill base. 1 From inside grill lid, align holes of left lid hinge (25) to grill lid (1) holes. Secure with screws (G) and flat washer (C). C Repeat step on other side with right lid hinge (26), washer (C) and screw (G). G 1 STEP 13 Position grill lid (1) on top of grill base (5), inserting lid hinges (26) (25) inside bottom hinges (23) (24). B 26 Align holes and secure hinges using screw (B).
ASSEMBLY 2g STEP 14 1 2b *Note: Wing nut is packaged with temperature gauge. Attach temperature gauge (2g) and temperature gauge base (2b) to grill lid (1) using wing nut. WING NUT Tip: Make sure the temperature readings and Masterbuilt logo in the gauge are aligned correctly before tightening down the wing nut. FIGURE 2 F 27 J D 13 27 1 STEP 15 Place bakelite spacer (F) on grill lid (1). Attach handle (27) using washers (J) and screws (D) as shown.
ASSEMBLY 11 STEP 16 Attach left side shelf (6) to both supports (11) using screws (G). 6 Repeat step on opposite side with right side shelf (3). GO BACK AND TIGHTEN ALL SCREWS AT THIS TIME. G Note: The left side shelf is the shelf with a square notch in it as seen in FIGURE 1. NOTCH 6 FIGURE 1 STEP 17 Place reflector plate (9) into bottom of grill base (5).
ASSEMBLY STEP 18 Attach heating element (4) to grill base (5) using screws (A) as shown. 5 A (A) M5 Thumb Screw 4 STEP 19 Position cooking grate (20) on top of grill base (5). 20 15 Note: The 2 support bars on cooking grate (20) should span left to right, with the grates going front to back. This alignment is essential for the next step.
ASSEMBLY STEP 20 Insert warming rack (21) onto cooking grate (20), with forks of warming rack straddling grate as shown in FIGURE 3. 21 20 5 FIGURE 3 6 10 5 STEP 21 Plug controller (10) into side of grill base (5) from below side shelf (6), coming in at a slight angle, carefully inserting plug while lifting so that top of controller slips into notch in shelf (6).
ASSEMBLY STEP 21 Slide drip tray (7) into drip tray bracket (8) from the right side. 8 ASSEMBLY IS COMPLETE 7 SAFE STORAGE AND MAINTENANCE • Inspect hardware and assembled parts on a regular basis to insure grill is in safe working condition. • ALWAYS allow grill to cool completely before handling. • ALWAYS empty drip tray after use only when ashes have completely cooled. • Clean grill, including special surfaces such as cooking grates with mild cleaning agents.
LIMITED WARRANTY Masterbuilt warrants its products to be free from defects in material and workmanship under proper assembly, normal use and recommended care for 90 days from the date of original retail purchase. Masterbuilt warranty does not cover paint finish as it may burn off during normal use. Masterbuilt warranty does not cover rust of the unit. Masterbuilt requires reasonable proof of purchase for warranty claims and suggests that you keep your receipt.
Masterbuilt Manufacturing, Inc. 1 Masterbuilt Ct. Columbus, GA 31907 Customer Service 1-800-489-1581 www.masterbuilt.
