Installation & Operations Manual Master-Bilt Products 908 Highway 15 North New Albany, MS 38652 Phone: (800) 684-8988 PN 071-90000 Rev 03/06/08 1
TABLE OF CONTENTS INTRODUCTION………………………………….……………………………………………………………………4 STORE CONDITIONS / LOCATION..………….…..………………………………………………………………..4 WARNING LABELS AND SAFETY INSTRUCTIONS………..…..……………………………………………… 5 PRE-INSTALLATION INSTRUCTIONS………………………..…..………………………………….…………… 6 Inspection for ShippingDamage……………………………………………………………….…………… 6 INSTALLATION INSTRUCTIONS………………………………………………………………………………….. 6 General Instructions…………………………………………………………………………………………. 6 Thermometer Installation…………………………………………………………………………………….
INTRODUCTION Thank you for purchasing a Master-Bilt cabinet. This manual contains important instructions for installing, using and servicing a Master-Bilt MPM/QMPM series open air case. Read all these documents carefully before installing or servicing your equipment. This manual should be left in the care of the store owner or manager. STORE CONDITIONS / LOCATION The Master-Bilt MPM/QMPM cases are designed to operate in the controlled environment of an air conditioned store.
The portion of this manual covering refrigeration and electrical components contains technical instructions intended only for persons qualified to perform refrigeration and electrical work. This manual cannot cover every installation, use or service situation.
PRE-INSTALLATION INSTRUCTIONS INSPECTION FOR SHIPPING DAMAGE You are responsible for filing all freight claims with the delivering truck line. Inspect all cartons and crates for damage as soon as they arrive. If damage is noted to shipping crates or cartons or if a shortage is found, note this on the bill of lading (all copies) prior to signing.
INSTALLATION INSTRUCTIONS GENERAL INSTRUCTIONS 1. Be sure the equipment is properly installed by competent service people. 2. Keep the equipment clean and sanitary so it will meet your local sanitation codes. Wipe up all spills,clean with water and a mild detergent, then rinse with clean water. A reservoir is provided to contain interior spills. Peridocially inspect reservoir and clean as needed. 3. Rotate your stock so that older stock does not accumulate.
CONDENSATE EVAPORATOR The MPM/QMPM is designed to operate in an environment of 75° ambient and 55% relative humidity. When the conditions are applicable for condensation such as high temperature and high humidity, a large capacity condensate evaporator has been installed in the MPM/QMPM to ensure proper evaporation. POWER TOGGLE SWITCH The toggle switch turns the power ON or OFF and is accessible through a slot at the back of the MPM/QMPM36 and MPM/QMPM-48 cabinet.
LOADING Do not place product in the case until 6 hours after it is started. Stock cases as quickly as possible, exposing only small quantities to store temperatures for short periods of time. It is important to keep stock rotated properly so that older stock does not accumulate. A “First-In, First-Out” rotation practice will keep the products in good salable condition. Avoid loading the case so that product sticks out beyond the shelves or blocking the return air grille at the bottom of the case.
MASTER-BILT PART NUMBERS The table below gives Master-Bilt part numbers. Use this chart when ordering replacement parts for your MPM/QMPM cases. All quantities are one each unless otherwise noted by parentheses.
PART NO. SHIP WT. LB/KG DESCRIPTION CASTERS A075-11140 Set of 4, 3" dia. for QMPM/MPM-36 and QMPM/MPM-48 17/8 A076-11140 Set of 6, 3" dia. for QMPM/MPM-72 26/12 SANDWICH RACKS - WELDED WIRE, CHROME PLATED 33-01450 16" L for QMPM and MPM models (Max. number of racks per model: -36 size: 2, -48 size: 3, -72 size: 4) 8/4 DIVIDERS FOR SANDWICH RACKS 33-01452 All QMPM and MPM models 1/0.
SALE AND DISPOSAL OWNER RESPONSIBILITY If you sell or give away your Master-Bilt cabinet you must make sure that all safety labels and the Installation Service Manual are included with it. If you need replacement labels or manuals, Master-Bilt will provide them free. Contact the customer service department at Master-Bilt at (800) 684-8988. The customer service department at Master-Bilt should be contacted at the time of sale or disposal of your cabinet so records may be kept of its new location.
12
13
14
15
