Model No. 240-0066 Owner’s Manual 17" VARIABLE SPEED DRILL PRESS WITH DIGITAL READOUT QUESTION... 1•877•393•7121 You will need this manual for safety instructions, operating procedures, and warranty. Put it and the original sales invoice in a safe, dry place for future reference.
TABLE OF CONTENTS SECTION SAFETY RULES PRODUCTION SPECIFICATIONS PAGE 1 Work Preparation Work Area Preparation Tool Maintenance Tool Operation ASSEMBLY Chuck . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5/8" Spindle Travel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1/2" 2 Table Movement. . . . . . . . . . . . . . 45° Bevel, 360° Swivel NET Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SAFETY RULES WARNING For your own safety, read and understand all warnings and operating instructions before using any tool or equipment. WARNING Some dust created by operation of power tool contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. To reduce your exposure to these chemicals: work in a well ventilated area and work with approved safety equipment.
2 ASSEMBLY UNPACKING Refer to Figure 1. • Check freight damage before opening the package. If freight damage is noticed, file claim with the carrier immediately. • Check to ensure all parts are present. Contact Customer Service Center at 1-877-393-7121 (M-F 9am – 5pm) immediately for missing parts. • Locate the following parts before assembling: A. Head Assembly B. Table C. Base D. Column Assembly E. Hex Bolts (4) F. Spring Washers (4) G. Feed Handles (3) H.
The drill press is designed to be safely assembled by at least two people working together. INSTALL COLUMN SUPPORT can rotate around the column smoothly. Adjust the retaining ring if necessary. • Align and attach the crank handle to the shaft on the table assembly. Secure with screw. • Thread and clamp tight the table locking handle to secure the table assembly on the column. ASSEMBLY WARNING Refer to Figure 2 Figure 3 Pinion Gear • Place the base on the floor or a bench.
ASSEMBLY Figure 5 Figure 7 Head Assembly Head Assembly Arbor 4 Chuck Set Screws Scrap Wood Mallet INSTALL HANDLES MOUNT DRILL PRESS • Locate the three thread holes on the hub of the head. • Thread the handles into the holes of hub until tight. • The machine must be installed in a well-lighted area with correct power supply. • The machine can be installed on either a workbench or a tool stand by using bolts, lock washers, and hex nuts.
GROUNDING INSTRUCTIONS WARNING Improper connection of equipment grounding conductor can result in the risk of electrical shock. • The machine should be grounded while in use to protect operator from electrical shock. • In the event of an electrical short circuit, grounding reduces the risk of electrical shock by providing an escape wire for the electric current.
OPERATION 6 WARNING Figure 11 - On-Off Switch For your own safety, read the entire operation manual and safety instructions before using the machine. injury. SAFETY PRECAUTIONS • Be aware of general power tool safety. Make sure all the safety rules are understood. • Disconnect the machine from power source whenever adjusting or replacing any parts. • Do not plug in unless switch is in “OFF” position. • Keep hands away from all moving parts.
Figure 15 7 OPERATION ADJUST SPEEDS Refer to Figure 14 WARNING To avoid damaging the drive belts and pulleys, DO NOT turn speed control knob unless the motor is running. Chuck Key Chuck Jaws The speed range is 450 RPM to 3000 RPM. To increase speed, turn the knob counterclockwise. To lower speed, turn the knob clockwise. The speed will display on the digital read-out panel.
MAINTENANCE 8 WARNING Turn the switch to the “OFF” position and disconnect the machine from power source before servicing or disassembling any components. CLEANING • Keep machine and workplace clean. Avoid accumulation of sawdust on the tool. • Be certain the motor is kept clean and free of dust. • Use soap and water to clean painted parts, rubber parts and plastic guards. LUBRICATION • A light coat of paste wax on the work table will make it easier to feed the workpiece and prevent rust.
TROUBLESHOOTING SYMPTOM Motor will not start POSSIBLE CAUSE(S) SOLUTIONS 1. Low voltage 2. Short circuit in line cord or plug 1. Check power supply for proper voltage 2. Inspect line cord and plug for faulty insulation or shorted connection 3. Inspect connection on motor. 4. Inspect connection on motor 3. Short circuit in motor 4. Open circuit or loose connection in motor 5. Incorrect fuses or circuit breakers 6. Defective switch 7.
10 17” DRILL PRESS PARTS ILLUSTRATION
17” DRILL PRESS PARTS LIST Key No.
12 MASTERFORCE™ 17” DRILL PRESS WARRANTY 90-DAY MONEY BACK GUARANTEE: This MASTERFORCE™ brand power tool carries our 90-DAY Money Back Guarantee. If you are not completely satisfied with your MASTERFORCE™ brand power tool for any reason within ninety (90) days from the date of purchase, return the tool with your original receipt to any MENARDS® retail store, and we will provide you a refund – no questions asked.
NOTE
Menard, Inc.
