Model MK-470 Tile Saw Owner’s Manual Parts List & Operating Instructions R Warning: • For your own safety read instruction manual before operating saw. • Wear eye protection. • Use splash hood for every operation for which it can be used. • Disconnect saw before servicing, when changing cutting wheels, and cleaning. • Use tool only with smooth edge cutting wheels free of openings and grooves. • Replace damaged cutting wheel before operating.
I M P O RTANT SAFETY INSTRUCTIONS FOR T H E MK-470 T I L E S AW Ta b l e o f C o n t e n t s General Safety Instructions Safety Messages Hazard Symbols Damage Prevention Messages Safety Label Locations Saw Features Motor Cutting Head Water Recirculation System Unpacking and Preparation Initial Assembly Installing the Cutting Head Installing the Blade Installing the Water Pump Electrical Requirements Lockout Method Sawing Operations General Cutting Guidelines Table Markings Maintenance Trouble Shooting Opti
Hazard Symbols Electrical Shock! Never touch electrical wires or components while the motor is running. Exposed, frayed or worn electrical motor and/or water pump wiring can be sources of electrical shock which could cause severe injury or burns. Accidental Starts! Before plugging the equipment into an electrical outlet, ensure that the ON/OFF switch is in the “OFF” position to prevent accidental starting. Unplug unit before performing any service operation.
Table Built of rugged composite material, the one-piece table allows for the cutting of 14” (355mm) tile and diagonally cuts 10" (254mm). Frame The structural steel frame of the MK-470 provides high strength and rigidity, while keeping weight to a minimum. The MK-470 is very portable at 29 pounds and an overall size of 28”L x 21”W x 25”H.
Warning This pump requires the use of a Ground Fault Circuit Interrupter. To reduce risk of electric shock, connect the saw to a Ground Fault Circuit Interrupter outlet when operating the saw with the pump plugged into the 3-pole receptacle on motor. See the pump manual and informational tags enclosed separately for all pump information. Caution Shock Hazard. For replacement pump, use only identical pump, MK model PES-100, part# 155987. n o t i c e Do not run the pump dry.
Extension Cords Use only extension cords that are intended for outdoor use. These extension cords are identified by a marking of, “Acceptable for use with outdoor appliances; store indoors while not in use.” Use only extension cords having an electrical rating not less than the rating of the product. Do not use damaged extension cords, do not “yank” on any cord to disconnect it from the power supply. Keep cord away from heat and sharp edges.
Use only MK DIAMOND authorized brushes to ensure compatibility and avoid motor damage. For best results use only MK DIAMOND blades. notice Warning Do not attempt to cut pieces too small to hold by hand outside the blade guard. Avoid awkward hand positions where a sudden slip could cause a hand or fingers to come in contact with the blade. When cutting any material, make sure it is fully supported. Hold workpiece firmly against the fence.
if blade won’t cut properly Check that the blade is the correct specification for material being cut. Check for worn out diamond edge & resharpen as necessary using dressing stick (MK part #152792), and slowly cut stick in (10) 1/16” slices to redress the diamond blade edge. Check that blade is rotating in the same direction as the rotation arrow. Make sure the blade core is not bent. table motion Check that the guide bar is clean and free of slurry build up.
MK-470 Exploded View B5 B4 L4 B2 L3 B1 L2 H6 L1 H5 A3 K1 H5 G4 K2 X3 G1 H3 K3 G2 A1 X2 A2 K4 G3 H1 X2 X2 A7 H2 H4 J3 X4 K8 B4 K5 B3 K7 J2 K6 X2 J1 M1 X2 X2 X2 X2 N4 N3 F2 F3 E2 F4 D3 E3 X2 N1 X2 X2 E4 D1 D2 s tile E1 E4 F1 E3 E2 aw
MK-470 Parts List Model MK-470 Tile Saw 120v/7.
K5 Wheel, Roller K6 Screw, 1/4-20 X 1 1/4 Hex Head Cap K7 Washer, 1/4 SAE Flat K8 Nut, 1/4-20 Hex L Assembly, Splash Curtain L1 Curtain, Splash L2 Bracket, Splash Curtain L3 Washer, 1/4 SAE Flat L4 Wingscrew, 1/4-20 X 1/2 M Table, 470 N Assembly, PES-100 120v Water Pump N1 Pump, Water, PES-100 120v N3 Hose, Vinyl, 1/4 ID N4 Clamp, Flow, 1/4-1/2 N5* Owner’s Manual, Water Pump *Not shown in exploded view Rev 12/00 2 2 2 2 1 1 1 1 1 1 1 1 2’ 1 1 151799 157145 151915 151893 155901-MK 134841 155901 151915 1518
HOW TO ORDER PARTS Please have the following information ready before calling: SERIAL NUMBER OF YOUR SAW MODELNUMBER OF SAW WHERE PURCHASED AND WHEN PART NUMBER PART DESCRIPTION All parts listed may be ordered from your local distributor or from mk diamond. If the part is not stocked locally, call :1 (800) 421-5830 or (310) 5395221 and ask for customer service. For technical support call: 1 (800) 474-5594 or (310) 257-2845. There is a $25.00 minimum order.
