Owner`s manual

ManualsBrandsMaster Spas ManualsHome building and Decorjet Away

OVERALL DESIGN INFORMATION

Line Voltage

The speciﬁed voltage within 10%± is required for proper operation of the propulsion GFCI and all

connected equipment. Should an auto transformer (also know as a buck-boost transformer) be

required, we recommend the following model:

Manufacturer: Dongan • Model: 80-M040 • Wire Conﬁguration: See “Technical Drawings” section

Serviceability and Equipment Access

The design information relating to structural, electrical, architectural, and plumbing design should

be adhered to so as to insure serviceability of the spa in the future. Non compliance with these

requirements could result in the warranty being voided.

PREPARATION OF THE SPA SITE

The owner will be responsible for all site preparation before and after delivery of the spa. All utili-

ties (water, sanitary, electrical, and etc.), mechanical pit, and applicable spa area structures must

be designed and installed by the owner. For information concerning details of these requirements,

consult the technical speciﬁcations included in this manual.

SPECIFICATIONS FOR SPA ROOM AREA

If installed indoors, the recommendation for the area in which the spa is contained is at least 3 feet

of separation between outer edge of spa and interior wall around perimeter and 8 feet high. This

is to allow adequate room for installation and proper deck space in the spa area. Extra space for

shower, storage cabinets, dehumidiﬁers, changing areas, and showers should be integrated into

these plans. Room dimensions may vary depending on requirements of the local and state regula-

tory authority having jurisdiction.

Temperature control and proper air handling (which should include humidity control) in the spa

room must be integrated into the room design to maintain a comfortable and safe environment for

the room occupants. Spa rooms are normally kept at 85 degrees Fahrenheit and spa water tempera-

tures are typically kept below 93 degrees Fahrenheit. This helps keep the differential between the

spa and room temperatures to a minimum.

Minimum Component Requirements (Installed components shall be NSF-50 certiﬁed for pool and spa use)

Filter Pump* Max. 1.5HP @ SF 1.10 Shall not exceed max. ﬁlter speciﬁcation, or 251 GPM

Jet Pump 1* Shall not exceed 251 GPM Recommended 1.5 HP @ 1.10 SF

Jet Pump 2* Shall not exceed 251 GPM Recommended 2.0 HP @ 1.10 SF

Chlorinator .5 lbs./day/1,000 gallons (level 3) Local/State codes may vary

Filter 200 sq. ft. Loading rate .375 GPM / sq. ft.

Recommended Components

Component Description Master Spas Part Number

Filter Pump Waterway Champion 1.5 HP Pump X320521

Jet Pump 1 Waterway Champion 2.0 HP Pump X320522

Jet Pump 2 Waterway Champion 1.5 HP Pump X320521

Chlorinator (level 3) Waterway Clear Water Tablet Feeder X268518

Filter Waterway ProClean 200 SF Filter X268516

Optional Skid Pack* Complete Skid Pack w/all components X620690

* Installer shall conﬁrm that the pumps are not capable of exceeding the maximum ﬂow rate speciﬁed on the installed suctions (251

GPM). This shall be conﬁrmed by either using recommended components, or testing the system prior to completion of install.

All pumps and ﬁltration systems components shall meet the requirements of: NSF/ANSI 50 and/or ANSI/UL 1081

*Skid pack comes with ﬁlter pump, jet pump 1, jet pump 2, chlorinator, ﬁlter, and plastic mounting plates.

Recommended components will satisfy the requirements of NSF-50 and most local and state codes. Should a local or state code require

a more restrictive component, the local code shall take priority over these recommended components unless code presents an unsafe

conﬁguration such as a pump that exceeds the ﬂow speciﬁcations of the installed suction.