Technical data

ManualsBrandsMaster ManualsPortable GeneratorBG 200

BENCH GRINDER

OPERATING INSTRUCTIONS

Models: BG150 & BG200

Charnwood, Cedar Court, Walker Road,

Bardon, Leicestershire LE67 1TU

Tel. 01530 516 926 Fax. 01530 516 929

email: sales@charnwood.net Website: www.charnwood.net

Charnwood, Cedar Court, Walker Road,

Bardon, Leicestershire LE67 1TU

Tel. 01530 516 926 Fax. 01530 516 929

email: sales@charnwood.net Website: www.charnwood.net

Model BG150 BG200

Motor 250w 375w

Voltage 240v 240v

No Load Speed 3450rpm 3450rpm

Spindle Diameter 1/2” (12.7mm) 5/8” (15.8mm)

Wheel Diameter 150mm (6”) 203mm (8”)

Wheel Thickness 20mm 25mm

Net Weight 10kg 17kg

Technical Data

Summary of content (6 pages)

PAGE 1
Technical Data Model Motor Voltage No Load Speed Spindle Diameter Wheel Diameter Wheel Thickness Net Weight BG150 250w 240v 3450rpm 1/2” (12.7mm) 150mm (6”) 20mm 10kg BG200 375w 240v 3450rpm 5/8” (15.8mm) 203mm (8”) 25mm 17kg Charnwood, Cedar Court, Walker Road, Bardon, Leicestershire LE67 1TU Tel. 01530 516 926 Fax. 01530 516 929 email: sales@charnwood.net Website: www.charnwood.
PAGE 2
GENERAL SAFETY RULES WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all instructions listed below may result in electric shock and/or serious personal injury. NOTE: This stationary tool has been manufactured in accordance with the applicable standard and equipment safety legislation. When using electrical appliances, it is important to take safety precautions to avoid possible injury and damage.
PAGE 3
Installing or Changing the Grinding Wheel (Figure 8) GENERAL SAFETY RULES WARNING! • Turn the power off and remove the plug from the outlet before changing the grinding wheels. When turning the grinder on with a newly installed wheel, DO NOT STAND IN FRONT OF THE GRINDER. Stand to the side and allow the grinder to run for at least one minute before using it. • Check grinding wheel frequently for wear or damage. Replace cracked wheels IMMEDIATELY. Replace worn wheels before the diameter reaches 4". 20.
PAGE 4
Table 1. Minimum Gage For Power Cord Rating Amp Grinding Total Length of cord in feet Volts 25 ft. 50ft 18 16 14 14 16 16 14 12 100ft 150 ft • Adjust the tool rest to accommodate large or unusually shaped workpieces. AWG 1-5 6-10 11-12 12-16 120V 120V 120V 120V • Allow grinder to reach full speed before contacting the work piece to the grinding wheel or other accessory 16 14 14 12 14 12 Not Recommended • Always keep the workpiece moving across the face of the grinding wheel.
PAGE 5
CALIFORNIA PROPOSITION 65 OPERATION WARNING! • Never touch the grinding wheel while it is moving. Do not touch the work piece after grinding, it will be very hot. • Always wear ANSI compliant safety glasses at all times while operating the grinder. WARNING: CHEMICAL HAZARD. Use of this tool may cause exposure to chemicals that are known to the state of California to cause cancer, birth defects or other reproductive harm.
PAGE 6
Installing Tool Rests (See Figure 3) 6" & 8" Bench Grinders 3X Magnifier Eye Shield Eye Shield Eye Shield Thumb Knobs Figure 3 1. Unscrew and remove the carriage bolt from the tool rest knob. Tool Rest Thumb Knob 2. Attach the tool rest bracket to the inside of the wheel guard as shown. Note: position lower slot in bracket over pin on wheel guard. Tool Rest Bracket 3. Attach tool rest to tool rest bracket with thumb knob (large). Note: V-groove tool rest mounts on left side.