METAL CONNECTOR NAILER 208-5019 OPERATOR'S MANUAL CAUTION: TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND OPERATOR'S MANUAL. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
TABLE OF CONTENTS Safety Instructions .......................................................... Page 2 Air Supply: Fittings, Hoses, Filters, Air Consumption, Regulators, Operation Pressure, Setting Correct Pressure ............... Page 5 Product Specifications .................................................... Page 6 Loading the Tool ............................................................. Page 7 Tool Operation ................................................................
SAFETY INSTRUCTIONS The purpose of safety symbols is to attract our attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The symbol warnings do not by themselves eliminate any danger. The instructions and warnings they give are no substitute for proper accident prevention measures.
SAFETY INSTRUCTIONS 1. EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when connecting to air supply, loading, operating or servicing this tool. Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury. 2. The employer and/or user must ensure that proper eye protection is worn.
SAFETY INSTRUCTIONS improperly feeding fasteners could result in serious personal injury. 17. Never use this tool in a manner that could cause a fastener to be directed toward the user or others in the work area. 18. Do not use the tool as a hammer. 19. Always be aware that misuse and improper handling of this tool can cause injury to yourself and others. 20. Never leave a tool unattended with the air hose attached. 21. Do not operate this tool if it does not contain a legible warning label. 22.
Do not use oxygen, combustible gases, or bottled gases as a power source for this tool as tool may explode, possibly causing injury. Keep the tool pointed away from yourself and others when connecting air source. A pressure regulator with an operating pressure of 0 - 125 p.s.i. (0 - 8.79 kg/cm2) is required to control the operating pressure for safe operation of this tool. Do not connect this tool to air pressure which can potentially exceed 200 p.s.i.
PRODUCTSPECIFICATIONS SPECIFICATIONS PRODUCT DRIVING POWER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 547 in.lbs FASTENER TYPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FULL ROUND HEAD NAIL (.131" and .148") FASTENER RANGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1/2" MAGAZINE CAPACITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LOADING • Never place a hand or any other part of the body in nail discharge area of tool while the air supply is connected. • Never point the tool at anyone else. • Never engage in horseplay. • Never pull the trigger unless nose is directed at the work. • Always handle the tool with care. • Do not pull the trigger or depress the trip mechanism while loading the tool. 1. Insert nail into track of magazine. 2. Pull pusher all the way back and then allow it to push nails forward to driving position.
TOOL OPERATION EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when connecting to air supply, loading, operating or servicing this tool. Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury. The employer and/or user must ensure that proper eye protection is worn.
TOOL OPERATION CHECK Keep the tool away from yourself and others when connecting air source. Remove all fasteners from tool before performing tool operation check.To reduce the risk of injury to yourself and others, check the tool before beginning work each day or if the tool is dropped, receive a sharp blow, been run over, etc. If the tool does not work as it should, contact Menards service center immediately. A. Press the contact trip against the work surface, without touching the trigger.
Do not store tools in a cold weather environment to prevent frost or ice formation on the tools operating valves and mechanisms that could cause tool failure.
NOTES Page 12
NOTES Page 13
METAL CONNECTOR NAILER WARRANTY 90-DAY MONEY BACK GUARANTEE This MASTERFORCE® brand power tool carries our 90-DAY Money Back Guarantee. If you are not completely satisfied with your MASTERFORCE® brand power tool for any reason within ninety (90) days from the date of purchase, return the tool with your original receipt to any MENARDS® retail store, and we will provide you a refund - no questions asked.
Menards, Inc., Eau Claire, WI 54703 Rev.
