Operator`s manual

ManualsBrandsMasterForce ManualsPower Tool241-0853

Operator’s Manual

Utila-Tool

Model No. 241-0853

IMPORTANT :

WARNING! Carefully read this Owner’s Manual before using this tool. Pay

close attention to all Safety Instructions, Warnings, and Caution sections. Use

this tool properly and only for its intended use.

afety symbols in this manual are used to ﬂag possible dangers. The safety

symbols and their explanations require the operator’s full understanding. The

safety warnings do not, by themselves, eliminate any danger, and they are not

a substitute for proper accident prevention measures.

This Safety Alert Symbol indicates caution, warning, or danger. Failure to

obey a safety warning can result in serious injury to yourself or to others. To

reduce the risk of injury, ﬁre, or electric shock, always follow the safety pre-

cautions.

Summary of content (11 pages)

PAGE 1
Operator’s Manual Utila-ToolTM Model No. 241-0853 IMPORTANT : WARNING! Carefully read this Owner’s Manual before using this tool. Pay close attention to all Safety Instructions, Warnings, and Caution sections. Use this tool properly and only for its intended use. Safety symbols in this manual are used to flag possible dangers. The safety symbols and their explanations require the operator’s full understanding.
PAGE 2
TABLE OF CONTENTS RULES FOR SAFE OPERATION Specifications .................................................................................................Page 2 KNOW YOUR TOOL Rules for Safe Operation............................................................................... Page 3 Description....................................................................................................... Page 7 Carefully read this Operating Manual and all labels affixed to the tool before using this tool.
PAGE 3
for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. √ I f operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock. 3) Personal safety √S tay alert, watch what you are doing and use common sense when operating a power tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication.
PAGE 4
provide for a secure stance. The power tool is guided more securely with both hands. √K eep your workplace clean. Blends of materials are particularly dangerous. Dust from light alloys can burn or explode. √D o not scrape wet or dampened materials (e.g., wallpaper) or on moist surfaces. Penetration of water into the machine increases the risk of an electric shock. DESCRIPTION KNOW YOUR UTILA-TOOLTM (Fig.
PAGE 5
SELECTING THE APPLICATION ACCESSORY VARIABLE SPEED DIAL The variable-speed dial delivers different speeds by turning the dial from position “1“(lowest speed) to position “6” (highest speed). ASSEMBLY AND ADJUSTMENT WARNING: If any part is broken or missing, DO NOT attempt to plug in the power cord or operate the tool until the broken or missing part is replaced. Failure to do so could result in possible serious injury.
PAGE 6
Paint & Varnish, Bonded Carpet, S c r a p i n g Soft Adhesives, Blade Vinyl Flooring, wood and other floor coverings. Sanding Pad and Sandpaper Bare or painted wood, plaster, and other surfaces, depending on sandpaper grit 1. D isconnect the tool from the power source. 2pcs 2. L oosen the flange bolt with the hex key supplied. (Fig. 5) 3. E nsure that the inner threads and the drive shaft are clean.
PAGE 7
4. P ress the sandpaper firmly against a smooth surface for a short period, then switch on the tool. The burr will form a non-slip bond with the outer edge of the sandpaper felt. This will avoid premature wear. 5. I f one point has become worn, pull off the sandpaper, turn it 120° and place it on the sanding pad again. MOUNTING THE FLANGES FOR DREMEL® BRAND OSCILLATING TOOL ACCESSORIES (Fig. 9 & 10) Fig.
PAGE 8
motor. size surfaces. Select low to medium speed. Excessive pressure can gouge or damage the background surfaces (e.g., wood, plaster). SANDING Sanding accessories are suitable for the dry sanding of wood, metal, surfaces, corners and edges and hard to reach areas. Work with the complete surface of the sanding pad, not only with the tip. Sand with a continuous motion and light pressure. DO NOT apply excessive pressure.
PAGE 9
HCS precision plunge cut saw blade/Wood 2pcs BIM plunge cut saw blade /Metal 2pcs Mini BIM Plunge Cut Saw Blade 1pc HSS segmented saw blade 1pc Triangular Grout 1pc Circular Grout 1pc or its employees. The rights under this limited warranty are to the original purchaser of the Merchandise and may not be transferred to any subsequent owner.
PAGE 10
18 19
PAGE 11
20