Garage Organization System Actual product may differ slightly from image shown EACH UNIT SOLD SEPARATELY 1-Door Wall Cabinet Model#: 2-Door Wall Cabinet Model#: 4-Drawer Base Cabinet Model#: 2-Door Base 2-Door Stacking Cabinet Cabinet Model#: Model#: 2-Door Tall Locker Model#: 211-4336 211-4340 211-4338 211-4332 211-4334 211-4319 211-4346 211-4349 211-4348 211-4342 211-4344 211-4331 211-4381 211-4396 211-4389 211-4361 211-4368 211-4341 OPERATOR’S MANUAL CAUTION: To Reduce The Risk Of Injury, User Mus
TABLE OF CONTENTS Safety Symbols.......................................................................... 3 Safety Instructions...................................................................... 4 Parts List.................................................................................... 5 Assembly and Operation............................................................ 9 Maintenance and Safety........................................................... 22 WARNING Cancer and Reproductive Harm – www.
SAFETY SYMBOLS Model #:________________________________ CAUTION: 1. Read and follow all safety and assembly instructions before using this product for the first time. 2. Fill in the following information and retain the manual for future reference: Place of purchase:_______________________ Date of purchase:________________________ Receipt # of purchase:___________________ Do not open more than one drawer at a time. Do not step on drawers. Do not allow children near the unit.
SAFETY INSTRUCTIONS The purpose of safety symbols is to attract our attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The symbol warnings do not by themselves eliminate any danger. The instructions and warnings they give are no substitute for proper accident prevention measures.
COMMON PARTS LIST M6 x 16 Phillips Head Bolt #320174 M6 x35 Hex Flange Bolt #321208 IMPORTANT PART FOR STACKING CABINET M6 x 40 Hex Tapping Screw #320328 M6 x 65 Hex Tapping Screw #320316 Washer #324050 M6 Hex Flange Nut #323085 Adjustable Feet #110068 Shelf Support #226078 Bracket #234542 Page 5
PARTS LIST For service regarding parts, assembly or warranty information, please call: 1-800-459-4409. 1-DOOR WALL CABINET 2-DOOR WALL CABINET The keys are placed inside the cabinet. These bolts and nuts are used to secure the sides of the cabinets together for a better appearance. The keys are placed inside the cabinet. 1 1 5 6 11 8 2 These bolts and nuts are used to secure 1 the sides of the cabinets 10 together for a better appearance.
PARTS LIST For service regarding parts, assembly or warranty information, please call: 1-800-459-4409. 4-DRAWER BASE CABINET 2-DOOR BASE CABINET The keys are placed inside the cabinet. The keys are placed inside the cabinet. These bolts and nuts are used to secure the sides of the cabinets together for a better appearance. These bolts and nuts are used to secure the sides of the cabinets together for a better appearance.
PARTS LIST For service regarding parts, assembly or warranty information, please call: 1-800-459-4409. 2-DOOR TALL LOCKER 2-DOOR STACKING CABINET The keys are placed inside the cabinet. These bolts and nuts are used to secure the sides of the cabinets together for a better appearance. The keys are placed inside the cabinet. This are the longer bolts to tie the cabinet together.
ASSEMBLY AND OPERATION Assembly is VERY EASY, however there are a few key steps that must be followed. THESE KEY STEPS ARE HIGHLIGHTED IN BOLD CAPS. FOLLOW THESE TO EXPEDITE ASSEMBLY. NECESSARY TOOLS REQUIRED FOR ASSEMBLY Attach the top panel to the cabinet using eight M6 x 16 Phillips head bolts. • Phillips head screwdriver • Drill/driver optional to speed up the assembly 1-DOOR WALL CABINET Carefully separate the front and back panels, allowing the side panels to unfold completely.
ASSEMBLY AND OPERATION Attach the bottom panel to the cabinet using eleven M6 x 16 Phillips head bolts. The cabinet weight capacity is determined by the stability of the surface it is mounted to. FOR BEST RESULTS, WALL CABINETS SHOULD BE MOUNTED TO STUDS OR OTHER SOLID SURFACES. Do not mount to drywall as it will not support the required weight and poses a danger if mounted incorrectly.
ASSEMBLY AND OPERATION Assembly is VERY EASY, however there are a few key steps that must be followed. THESE KEY STEPS ARE HIGHLIGHTED IN BOLD CAPS. FOLLOW THESE TO EXPEDITE ASSEMBLY. 2-DOOR WALL CABINET Carefully separate the front and back panels, allowing the side panels to unfold completely. Attach the top panel to the cabinet using eight M6 x 16 Phillips head bolts. Carefully lay the cabinet on its back on a soft surface to protect the finish.
ASSEMBLY AND OPERATION Attach the bottom panel to the cabinet using eleven M6 x 16 Phillips head bolts. The cabinet weight capacity is determined by the stability of the surface it is mounted to. FOR BEST RESULTS, WALL CABINETS SHOULD BE MOUNTED TO STUDS OR OTHER SOLID SURFACES. Do not mount to drywall as it will not support the required weight and poses a danger if mounted incorrectly.
ASSEMBLY AND OPERATION 4-DRAWER BASE CABINET Carefully lay the cabinet on its back on a soft surface to protect the finish. Screw the four adjustable feet onto the bottom of the cabinet. To replace a drawer, extend the drawer slides from the cabinet. Insert the brackets on each side of the drawer into the slots in the cabinet slides, BEING CAREFUL THAT THEY ARE POSITIONED PROPERLY. Once properly inserted, completely close the drawer to set the slides in their proper positions.
ASSEMBLY AND OPERATION Assembly is VERY EASY, however there are a few key steps that must be followed. THESE KEY STEPS ARE HIGHLIGHTED IN BOLD CAPS. FOLLOW THESE TO EXPEDITE ASSEMBLY. 2-DOOR BASE CABINET Carefully separate the front and back panels, allowing the side panels to unfold completely. Carefully lay the cabinet on its back on a soft surface to protect the finish. INSERT THE LIP OF THE BOTTOM PANEL INTO THE SLOT ON THE BACK OF THE CABINET, MAKING SURE THAT THE HOLES ALIGN.
ASSEMBLY AND OPERATION Screw four adjustable feet into the bottom of the cabinet. Insert four shelf supports inside the cabinet at the desired height. Note: to use the locking mechanism, the shelf must be placed in the center position. Place the shelf on the shelf supports. CAUTION: The maximum shelf capacity should be no more than 150 lbs Attach the work top to the cabinet using four M6 x 16 Phillips head tapping bolts.
ASSEMBLY AND OPERATION Assembly is VERY EASY, however there are a few key steps that must be followed. THESE KEY STEPS ARE HIGHLIGHTED IN BOLD CAPS. FOLLOW THESE TO EXPEDITE ASSEMBLY. 2-DOOR STACKING CABINET Carefully separate the front and back panels, allowing the side panels to unfold completely. NOTE: IF YOU ARE STACKING TWO CABINETS, YOU NEED TO PICK ONE CABINET TO BE ON THE TOP AND ONE CABINET TO BE ON THE BOTTOM. ASSEMBLE THE BOTTOM CABINET FIRST.
ASSEMBLY AND OPERATION Screw four adjustable feet into the bottom of the cabinet. Turn cabinet over, setting it on the four leveling feet. Insert four shelf supports inside the cabinet at the desired height. Note: to use the locking mechanism, the shelf must be placed in the center position. Place the shelf on the shelf supports. CAUTION: The maximum shelf capacity should be no more than 150 lbs FOR THE BOTTOM CABINET, PLACE THE TOP PANEL ON THE CABINET, BUT DO NOT ATTACH WITH THE BOLTS.
ASSEMBLY AND OPERATION Assembly is VERY EASY, however there are a few key steps that must be followed. THESE KEY STEPS ARE HIGHLIGHTED IN BOLD CAPS. FOLLOW THESE TO EXPEDITE ASSEMBLY. FOR THE TOP CABINET, ATTACH THE TOP PANEL TO THE CABINET USING EIGHT M6 X 16 PHILLIPS HEAD BOLTS. Turn the cabinet over and assemble the bottom panel as shown below. TILT THE BOTTOM PANEL ONTO THE BOTTOM OF THE CABINET.
ASSEMBLY AND OPERATION Assembly is VERY EASY, however there are a few key steps that must be followed. THESE KEY STEPS ARE HIGHLIGHTED IN BOLD CAPS. FOLLOW THESE TO EXPEDITE ASSEMBLY. STACKING CABINETS REVIEW To stack two cabinets, you first need to assemble two cabinets. CONNECT THE CABINETS USING FOUR LONG M6 X 35 HEX FLANGE BOLTS. BOTTOM CABINET (A): Install the bottom panel, adjustable feet and shelf. PLACE THE TOP PANEL IN PLACE. DO NOT USE BOLTS, THEY WILL INTERFERE WITH STACKING.
ASSEMBLY AND OPERATION OPTIONAL: WORK TOP OPTIONAL: LAMINATE COUNTER TOP The taller "stacking cabinet" can also be used as a base cabinet. You can replace the metal top that comes with the unit with an optional stainless steel top (sold separately). Masterforce cabinets are built to the same size specification as most kitchen cabinetry. This offers a very unique opportunity to combine the durability of metal cabinets with the beauty and versatility of Customcraft laminate counter tops.
ASSEMBLY AND OPERATION Assembly is VERY EASY, however there are a few key steps that must be followed. THESE KEY STEPS ARE HIGHLIGHTED IN BOLD CAPS. FOLLOW THESE TO EXPEDITE ASSEMBLY. 2-DOOR TALL LOCKER NOTE: THIS INSTALLATION PROCESS REQUIRES AT LEAST TWO PEOPLE. Carefully separate the front and back panels, allowing the side panels to unfold completely. Carefully lay the cabinet on its back on a soft surface to protect the finish.
ASSEMBLY AND OPERATION Screw four adjustable feet into the bottom of the cabinet. Attach the vertical panel to the tall locker in front using two M6 x 16 Phillips head bolts. ATTACH THE TOP PANEL TO THE CABINET USING EIGHT M6 X 16 PHILLIPS HEAD BOLTS. Stand the tall locker upright. Insert the vertical panel into the tall locker. Attach the vertical panel to the tall locker in back using four M6 x 16 Phillips head bolts.
ASSEMBLY AND OPERATION Insert four shelf supports inside the cabinet in the top holes. Insert eight shelf supports inside the cabinet at the desired heights. Place the long shelf on the shelf supports. Place the two short shelves on the shelf supports. Connect the vertical panel to the shelf using two M6 x 16 Phillips head bolts. Fasten the top of the locker to the wall using two M6 x 65 hex tapping screws and washers.
ASSEMBLY AND OPERATION OPTIONAL: DIFFERENT COLORS TRIM Door and drawer trim is available in three different colors to further customize your design.
MAINTENANCE AND SAFETY MAINTENANCE Lubricate the slides (twice a year) with a product like WD40 or other quality lubricant. This is especially true as the temperature decreases, the bearing can become stiff. Periodically the drawer fronts, drawer trim, and other surfaces should be cleaned with mild detergent and water. Grease and oil can be removed with most standard cleaning fluids. For safety, use a nonflammable cleaning fluid.
NOTES Page 26
Garage Organization System LIMITED LIFETIME WARRANTY MASTERFORCE® Tool Cabinets and Chests have been manufactured to the highest standards of quality and workmanship and are warranted to be free from defects in materials and workmanship under normal use for the lifetime that you own the product. If any part of the product is found to be defective during normal use, the defective product or part will be replaced at our discretion.
©2020 Menard, Inc.
