Brushless Compact Drill 241-0381 OPERATOR’S MANUAL CAUTION: To Reduce The Risk Of Injury, User Must Read And Understand Operator’s Manual. Save These Instructions For Future Reference. For questions / comments, technical assistance or repair parts – Please Call Toll Free: 1-866-917-4374 (M-F 8:30am-5:00pm EST).
TABLE OF CONTENTS Safety Symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 2 Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 3 Overview/Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 8 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SAFETY SYMBOLS Some of these following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and more safely.
SAFETY INSTRUCTIONS The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The symbol warnings do not, by themselves, eliminate any danger. The instructions and warnings they give are no substitutes for proper accident prevention measures.
SAFETY INSTRUCTIONS GENERAL POWER TOOL SAFETY WARNINGS WARNING: Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/ or serious injury. SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE. The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. WORK AREA SAFETY 1.
SAFETY INSTRUCTIONS 5. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. 6. Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts. 7. If devices are provided for the connection of dust extraction and collection facilities, ensure that these are connected and properly used.
SAFETY INSTRUCTIONS 5. Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury. 6. Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature above 212 °F (100 °C) may cause explosion. 7. Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions.
SAFETY INSTRUCTIONS 2. For best results, your battery and tool should be stored, charged and used in a location where the temperature is more than 41°F (5°C) but less than 104°F (40°C). Do not store outside or in vehicles. DANGER: People with electronic devices, such as pacemakers, should consult their physician(s) before using this product. Operation of electrical equipment in close proximity to a heart pacemaker could cause interference or failure of the pacemaker.
OVERVIEW Torque-Adjustment Ring Two-Speed Gearbox Switch Chuck Sleeve Direction-Of-Rotation Selector Variable-Speed Trigger Switch LED Worklight Bit Holder SPECIFICATIONS Rated Voltage 20 V d.c. No-load Speed 0-500/0-1,850 RPM Chuck Capacity 1/2” (13mm) Max. Torque 525 in. lbs. Clutch Settings 17 positions +1 drill mode Weight (without battery) 2 lb. 3 oz.
ASSEMBLY WARNING: If any part is broken or missing, DO NOT attach the battery pack or operate the tool until the broken or missing part is replaced. Failure to do so could result in possible serious injury. WARNING: Do not attempt to modify this tool or create accessories not recommended for use with this tool. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious injury.
OPERATION TO INSTALL THE BELT CLIP (FIG. 2) 1. Align the rib of the clip with the hole on the base of the drill/driver. 2. Insert the screw and tighten the screw securely with a screwdriver (not included). The belt clip can be positioned on either side of the tool. Your drill/driver is equipped with a bit holder on the heel of the tool. After using the bit, you can insert the bit into the bit holder for convenient storage. LED WORKLIGHT (FIG. 4) FIG. 4 TO REMOVE THE BELT CLIP (FIG. 2) 1.
OPERATION 1. To turn the drill/driver ON, press the trigger switch. FIG. 6 2. To turn the drill/driver OFF, release the trigger switch. 3. The variable-speed trigger switch delivers higher speed with increased trigger pressure and lower speed with decreased trigger pressure. WARNING: Allow the motor to come to a complete stop before setting the drill/driver down. ELECTRIC BRAKE To stop the drill/driver, release the trigger switch and allow the chuck to come to a complete stop.
OPERATION FIG. 7 TORQUE ADJUSTMENT (FIG. 9) High FIG. 9 To Decrease Torque Torque-Adjustment Ring Low To Increase Torque KEYLESS CHUCK (FIG. 8) The drill/driver has a keyless chuck to secure or release bits in the chuck jaws. The arrows on the chuck indicate the direction in which to rotate the chuck in order to tighten or loosen the chuck jaws on the bit. WARNING: Do not hold the chuck with one hand and use the power of the drill/driver to tighten the chuck jaws on the drill bit.
OPERATION DRILL MODE (FIG. 10) FIG. 10 5. Tighten the chuck jaws securely on the bit. TO REMOVE THE BIT (FIG. 11) 1. Remove the battery pack from the drill/ driver. Torque Indicator Drill Icon 2. Open the chuck jaws. 3. Rotate the chuck in the direction of the arrow marked “RELEASE” to loosen the chuck jaws. 4. Remove the bit. WARNING: Select the drill mode for drilling and other heavy-duty applications.
OPERATION 7. If the bit jams in the workpiece or if the drill stalls, stop the tool immediately. Remove the bit from the workpiece and determine the reason for jamming. DRILLING IN WOOD For maximum performance, use high-speed steel (available separately) or brad-point bits (available separately) for wood drilling. 1. When drilling “through” holes, place a block of wood behind the workpiece to prevent ragged or splintered edges on the back side of the hole. 2.
MAINTENANCE WARNING: • When servicing, use only identical replacement parts. Use of any other parts may create a hazard or cause product damage. • To avoid serious personal injury, always remove the battery pack from the product when cleaning or performing any maintenance. • Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use a clean cloth to remove dirt, dust, oil, grease, etc.
TROUBLESHOOTING PROBLEM The drill/driver does not work. The bit cannot be installed. Motor is overheating. CAUSE SOLUTION The battery is depleted. Charge the battery. The chuck is not opened. Open the chuck. The bit does not fit the chuck. Use a suitable bit. The ventilation slots may be obstructed. Clean and clear the ventilation slots. Do not cover the ventilation slots with your hand during operation.
NOTES Page 17
BRUSHLESS DRILL/DRIVER WARRANTY 90-DAY MONEY BACK GUARANTEE: This MASTERFORCE® brand power tool carries our 90-DAY Money Back Guarantee. If you are not completely satisfied with your MASTERFORCE® brand power tool for any reason within ninety (90) days from the date of purchase, return the tool with your original receipt to any MENARDS® retail store, and we will provide you a refund – no questions asked.
© 2021 Menard, Inc.
